The Fibaro Z-Wave Single Switch 2 is a wireless Z-Wave module which can control appliances or lighting up to a maximum load of 2.0kW.
Control the ON-OFF function of a circuit remotely or using a wall switch
Compatible with all Z-Wave networks
Acts as a repeater expanding your Z-Wave network
Wide range of compatibility with existing light fittings and does NOT require expensive cabling
control loads up to 2kW (8A)
The main differences in the FGS-213 are:
Z-Wave Plus certification
Has power monitoring
230V powered only (this is the same as the FGS-212)
No dry contacts - this is important. It means that the new FGS-213 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
The Fibaro Z-Wave In-Wall Dimmer 2 (FGD-212) is the newest version of a popular wireless controller designed to operate behind a wall switch.
Control the level of illumination of your light remotely or using a manual button (in two and three way configurations)
Implemented algorithm of smart light source detection
Acts as a repeater expanding your Z-Wave network
Wide range of compatibility with existing light fittings and does NOT require expensive re-wiring
Active power and energy metering functionality
Works with various types of manual buttons
Active element: semiconductor electronic switch
FIBARO Smart Implant allows to enhance the functionality of wired sensors and other devices by adding Z-Wave network communication.
You can connect binary sensors, analog sensors, DS18B20 temperature sensors or DHT22 humidity and temperature sensor to report their readings to the Z-Wave controller.
It can also control devices by opening/closing output contacts independently of the inputs.
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
Completely wireless
Z-Wave Plus certified
Supports 6 different actions/scenes
Available in multiple colours (white, black, red, blue, yellow)
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
Completely wireless
Z-Wave Plus certified
Supports 6 different actions/scenes
Available in multiple colours (white, black, red, blue, yellow)
Content
Product Details
The Fibaro Z-Wave Single Switch 2 is a smart Z-Wave module capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.
The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.
This Fibaro Z-Wave Single Switch 2 requires 3-wire (including neutral) installation and works with an AC (110-230V) or DC (24-60V) power supply.
The Fibaro Z-Wave Single Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits.
This product integrates with all Australian certified (921.42MHz) Z-Wave controllers including:
Raspberry PI with RaZberry Card
Fibaro Home Controller 2/Lite
DHS Z-Wave Universal Remote Controller
DHS Z-Wave Mini Remote Controller
Configuring Z-Wave Devices
Z-Wave devices often have several configurable parameters which you can change using your Vera?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller.
Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section.
Please check the maximum load before installing or operating.This installation must be done by a certified electrician in Australia and New Zealand.Before engaging an electrician, check that they provide an electrical compliance certificate.For a warranty claim, you have to provide an installation compliance certificate from your electrician.
The Fibaro Z-Wave In-Wall Dimmer 2 is designed to operate with or without a neutral wire. It may be used as a switch in systems without a neutral wire.
In the case of a 2-wire connection (no neutral), the Fibaro Z-Wave In-Wall Dimmer 2 may require a minimum load of 50W depending on the specifics of the connected load.
When used with a Fibaro Dimmer Bypass 2 it may operate with any compatible (see below) load from 5W. Before committing to buy Fibaro Dimmer Bypass 2 please check if your load can be properly controlled by Fibaro Dimmer 2 without a bypass device.
Do not connect this device to a power supply without a load. Only lighting devices may be connected to this device.
As a dimmer it operates with the following loads:
230V operated conventional incandescent (from 50W to 250W)
230V operated halogen (from 50W to 200W)
12 V operated ELV halogen lamps and dimmable LED lamps (with electronic transformers: Trailing and Leading-edge type) (from 50W to 200W)
Dimmable CFL tube lamps with electronic ballast only (from 50W to 200W)
As a switch it operates with the following loads:
Compact fluorescent lamps with electronic ballast
LED bulbs (power factor >0.7)
Fluorescent tube lamps with electronic ballast
Please note: For loads other than resistive do not exceed a 1.5A current.
This product integrates with all Australian certified (921.42 MHz) Z-Wave and Z-Wave Plus controllers including:
Vera Plus/ Edge
Fibaro Home Center 2 / Lite
Please note: Do not mix the load type (e.g. LED and CFL or different types of transformers) as it will impede the proper operation of the dimmer. Doing so will void the dimmer's warranty.
This product must be installed by a qualified electrician.Before engaging an electrician, check that they provide a warranty and electrical compliance certificate.For a warranty claim, you have to provide an installation compliance certificate from your electrician.PLEASE NOTE FOR THE INSTALLATIONS IN THE AREAS WHERE ELECTRICITY SUPPLIERS USE OFF-PEAK RIPPLE CONTROL SIGNALS:
Electricity suppliers in particular areas of Australia such as NSW, QLD and some other places are injecting an off-peak ripple control signal using Zellweger equipment or similar onto their distribution networks in order to remotely control devices such as off-peak hot water systems and street lighting, although other areas within Australia also use this technology. Not all properties are affected by ripple control, so just because you might live in one of these areas, does not mean that you will have these problems.
Ripple injection control systems work by superimposing coded control signals, commonly 750Hz or 1050Hz on the 50 Hz mains supply.
Some electrical appliances such as fans, dimmers, toasters and LED lighting can be sensitive to this ripple control signal. The results could be audible buzzing noises from fans or flickering lights whenever the ripple control signals are present.
Electricity suppliers are advising users to install appropriate ripple signal filters in such areas.
The ripple signal filter is a tuned passive inline filter that completely eliminates the superimposed ripple injection control signal from the normal mains supply to produce a noise free filtered mains supply which can then be connected to the electrical appliances or light control systems. The ripple signal filter is specifically tuned to eliminate the ripple control signal frequency of 750Hz or 1050Hz.
However, we can?t guarantee the ripple signal filter always will help you if you experiencing such issues. Please contact your local energy provider to get more information and proposed solutions for your electrical installation.
If you are getting similar problems with your dimmers and fans and it?s not Ripple Control Signal and you are hearing the tones at random times of the day, your electrical supply may be affected by harmonics; a power fluctuation that is not part of the normal electricity supply or ripple control signal output.
Harmonics are caused by interference created by other equipment on the network, such as inverter type air conditioners and switch mode power supplies for computers.
The offending appliances may be in your home or other premises on the local power grid. If you are being affected by network harmonics, it may be of benefit to transfer the electricity supply to your premises to a different phase in the street. This is something you will need to discuss with your electrical company.
We are strongly recommending for the areas we have mentioned above to run tests with only a few dimmers before committing for high volumes. If results are not fully OK you may use relays only instead of dimmers.
Please note that our warranty for the faulty devices is not covering above mentioned conditions with your local electric grids.
Please see affected with Ripple Signalling areas here:
QUEENSLAND
Only Southern Queensland (Energex) has Ripple Signalling.
The Frequency is 1050Hz.
The rest of Queensland (Ergon) does not have Ripple Signalling.
Up to 30m indoors (depending on building materials)
Application
Indoor use only
Operation temperature
0 ~ 35 ?C
Dimensions (L x W x H)
42.5mm x 38.25mm x 20.3mm
Weight
30g
Operational Current
0.25 - 1.1A
Compliance
RCM E3606
Dimming type compatibility
Leading and Trailing Edge
Product Description
Supports Z-Wave network Security Modes: S0 with AES-128 encryption and S2 Authenticated with PRNG-based encryption.
Works as a Z-Wave signal repeater.
Allows for connecting sensors:
6 DS18B20 sensors,
1 DHT sensor,
2 2-wire analog sensor,
2 3-wire analog sensor,
2 binary sensors.
Built-in temperature sensor.
This product works with :
Fibaro Home Controller 3/2/Lite
Please note:
THE DEVICE IS NOT COMPATIBLE WITH VERA HOME CONTROLLERSBefore installation
Connect only in accordance with one of the diagrams,
The device is powered with secure voltage; nevertheless, the user should be extra careful or should commission the installation to a qualified person,
Do not connect devices that are not compliant with the specification,
Do not connect other sensors than DS18B20 or DHT22 to SP and SD terminals,
Do not connect sensors to SP and SD terminals with wires longer than 3 meters,
Do not load the device outputs with a current exceeding 150mA,
Every connected device should be compliant with the relevant safety standards,
Unused lines should be left insulated.
Tips for arranging the antenna:
Locate the antenna as far from metal elements as possible (connecting wires, bracket rings, etc.) in order to prevent interferences,
Metal surfaces in the direct vicinity of the antenna (e.g. flush mounted metal boxes, metal door frames) may impair signal reception!
Do not cut or shorten the antenna ? its length is perfectly matched to the band in which the system operates.
Make sure no part of the antenna sticks out of the wall switch box.
Product Details
The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway.
The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene.
Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk)
Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.
Technical Specifications
RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS
Product Details
The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway.
The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene.
Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk)
Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.
