QUBINO Z-Wave Thermostat 2

$88.99

Availability: In Stock

The?QUBINO On/Off Thermostat 2? (made by Goap Europe) is your wireless heating and hot water controller that also measures power consumption. This amazingly tiny module is ideal for wireless control of electric or water-based underfloor heating systems, electric water heaters, hot water pumps, and electric radiators.

  • Z-Wave Plus certified, Security S2, SmartStart ready
  • Includes digital temperature sensor
  • Can measure the power consumption of the connected device (within 3% accuracy)
  • Extremely low energy consumption (less than 0.4W)
  • Frost-free mode: Specifies a minimum temperature for the heating system connected to the module to prevent your pipes from freezing

20 in stock

SKU: DHS-HVAC-THR-QUB-02 Categories: , Tags: , ,

Description

The?QUBINO?Z-Wave ON/OFF Thermostat?2?can be used to directly control electric or water-based underfloor heating systems, electric water heaters, hot water pumps, electric radiators and similar. You can control it either remotely through the Z-Wave network or through wall switches.

The?QUBINO?Z-Wave ON/OFF Thermostat?2?also measures power consumption and supports the connection of a digital temperature sensor.

This product integrates with Australian certified (921.42 MHz) Z-Wave Controllers including?Fibaro Home Center?

Please check the compatibility with major Z-Wave controllers in this?Matrix provided by the manufacturer.

Product Support

Videos / YouTube:

Technical Specification

RF Protocol
Z-Wave Plus (500 series chip), Security S2
SmartStart ready, Z-Wave Repeater
RF Frequency
921.42Mhz – AU/NZ ?approved RF for Z?wave
Z-Wave device type
Z-Wave binary switch, routing slave
Power Supply
230V AC?? 10% OR 24-30V DC
Rated Load Current of AC Output?(resistive load)
1 x 10A / 230V AC
Rated Load Current of DC Output?(resistive load)
1 x 10 A / 30V DC
Output circuit power of AC output?(resistive load)
2300W (230V AC)
Output circuit power of DC output (resistive load) 240W (24V DC)
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
-10 ~ 40 ?C
Digital Temperature Sensor cable length
1000 mm
Weight
48g
Dimensions
41.8mm x 36.8mm x 16.9mm

Quick Comparison

SettingsQUBINO Z-Wave Thermostat 2 removeFIBARO Z-Wave Button (Black) removeFIBARO ZWave Single Switch 2 removeFIBARO Z-Wave Roller Shutter 3 removeFIBARO Z-Wave Button (Yellow) removeFIBARO Z-Wave Button (Red) remove
Image
SKUDHS-HVAC-THR-QUB-02DHS-CON-SBUT-FIB-BLDHS-LIT-SWW-FIB-012DHS-WIN-BLD-FIB-3DHS-CON-SBUT-FIB-YLDHS-CON-SBUT-FIB-RD
Rating
Price$88.99$78.00$84.99$84.99$78.00$78.00
Stock

20 in stock

Out of stock

Out of stock

20 in stock

1 in stock

2 in stock

Availability20 in stockOut of stockOut of stock20 in stock1 in stock2 in stock
Add to cart

Add to basket

Read more

Read more

Add to basket

Add to basket

Add to basket

DescriptionThe?QUBINO On/Off Thermostat 2? (made by Goap Europe) is your wireless heating and hot water controller that also measures power consumption. This amazingly tiny module is ideal for wireless control of electric or water-based underfloor heating systems, electric water heaters, hot water pumps, and electric radiators.
  • Z-Wave Plus certified, Security S2, SmartStart ready
  • Includes digital temperature sensor
  • Can measure the power consumption of the connected device (within 3% accuracy)
  • Extremely low energy consumption (less than 0.4W)
  • Frost-free mode: Specifies a minimum temperature for the heating system connected to the module to prevent your pipes from freezing
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
  • Completely wireless
  • Z-Wave Plus certified
  • Supports 6 different actions/scenes
  • Available in multiple colours (white, black, red, blue, yellow)
The Fibaro Z-Wave Single Switch 2 is a wireless Z-Wave module which can control appliances or lighting up to a maximum load of 2.0kW.
  • Control the ON-OFF function of a circuit remotely or using a wall switch
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling
  • control loads up to 2kW (8A)
The main differences in the FGS-213 are:
  • Z-Wave Plus certification
  • Has power monitoring
  • 230V powered only (this is the same as the FGS-212)
  • No dry contacts - this is important. It means that the new FGS-213 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
The Fibaro Roller Shutter Controller is designed to control blind, awning, garage door and gate motors.
  • Supports five different types of motor systems
  • Precise positioning of blind or awning
  • Automatic calibration
  • Wireless control of AC motors with "three wires" interface
  • Monitor and analyse energy usage
FIBARO Roller Shutter 3 (FGR-223) is a new Z-Wave Plus version of its predecessor model Fibaro Roller Shutter 2.
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
  • Completely wireless
  • Z-Wave Plus certified
  • Supports 6 different actions/scenes
  • Available in multiple colours (white, black, red, blue, yellow)
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
  • Completely wireless
  • Z-Wave Plus certified
  • Supports 6 different actions/scenes
  • Available in multiple colours (white, black, red, blue, yellow)
ContentThe?QUBINO?Z-Wave ON/OFF Thermostat?2?can be used to directly control electric or water-based underfloor heating systems, electric water heaters, hot water pumps, electric radiators and similar. You can control it either remotely through the Z-Wave network or through wall switches. The?QUBINO?Z-Wave ON/OFF Thermostat?2?also measures power consumption and supports the connection of a digital temperature sensor. This product integrates with Australian certified (921.42 MHz) Z-Wave Controllers including?Fibaro Home Center? Please check the compatibility with major Z-Wave controllers in this?Matrix provided by the manufacturer.

Product Support

Videos / YouTube:

Technical Specification

RF Protocol
Z-Wave Plus (500 series chip), Security S2
SmartStart ready, Z-Wave Repeater
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z?wave
Z-Wave device type
Z-Wave binary switch, routing slave
Power Supply
230V AC?? 10% OR 24-30V DC
Rated Load Current of AC Output?(resistive load)
1 x 10A / 230V AC
Rated Load Current of DC Output?(resistive load)
1 x 10 A / 30V DC
Output circuit power of AC output?(resistive load)
2300W (230V AC)
Output circuit power of DC output (resistive load) 240W (24V DC)
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
-10 ~ 40 ?C
Digital Temperature Sensor cable length
1000 mm
Weight
48g
Dimensions
41.8mm x 36.8mm x 16.9mm

Product Details

The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway. The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene. Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk) Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers. FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS

Product Details

The Fibaro Z-Wave Single Switch 2 is a smart Z-Wave module capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene. The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician. This Fibaro Z-Wave Single Switch 2 requires 3-wire (including neutral) installation and works with an AC (110-230V) or DC (24-60V) power supply. The Fibaro Z-Wave Single Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits. This product integrates with all Australian certified (921.42MHz) Z-Wave controllers including:
  • Raspberry PI with RaZberry Card
  • Fibaro Home Controller 2/Lite
  • DHS Z-Wave Universal Remote Controller
  • DHS Z-Wave Mini Remote Controller

Configuring Z-Wave Devices

Z-Wave devices often have several configurable parameters which you can change using your Vera?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller. Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section. Please check the maximum load before installing or operating. This installation must be done by a certified electrician in Australia and New Zealand. Before engaging an electrician, check that they provide an electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician.  

Technical Specifications

RF Protocol Z-Wave
RF Frequency 921.42Mhz - AU/NZ ?approved RF for Z?wave
Z?Wave device type Z-Wave Switch, Routing Slave
Power 110-230V?? 10% 50/60 Hz
Operation Range Up to 20m indoors with no obstacles
Weight 50g
Housing ABS
Compliance EN 55015, EN 60669-2-1
Regulatory Compliance Mark N5496
Dimensions (LxWxH) 42mm x 37mm x 17mm
 

Wiring Diagram

 

 

Documentation

Fibaro Z-Wave Single Switch 2 Manual (Size: 724 Kb) Configuring_ZWave_Device_Parameters_in_VeraUI7

Product Details

The Fibaro Roller Shutter 3 (FGR-223) is an advanced Z-Wave controller for automated roller blinds, awnings, venetian blinds, garage doors and gates. The module can control devices that are powered by an AC electric motor with a "three wire" interface. The Roller Shutter module features automatic calibration so that you can precisely position the blind. It also includes a power metering feature to help you measure power consumption. The Fibaro Roller Shutter 2 has five modes that enable it to perfectly control any electric garage door, gate, roller blind, awning or Venetian blind. This allows for the correct configuration and operation of a device through a special interface icon (via the Fibaro HC2).
  • Roller blinds with positioning
  • Roller blinds without positioning
  • Garage doors with positioning
  • Garage doors without positioning
  • Venetian blind

Configuring Z-Wave Devices:

Z-Wave devices often have several configurable parameters which you can change using your Vera?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active for or the type of manual switch connected to a Z-Wave light controller. Every available configurable parameter is listed in your device?s user manual. In most cases your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section. This product must be installed by a qualified electrician. Before engaging an electrician, check that they provide a warranty and electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician.

Technical Specifications

RF Protocol Z?Wave Plus
RF Frequency 921.42Mhz ? AU/NZ ?approved RF for Z?wave
Z?wave device type Z-Wave multiple level dimmer, routing slave
Power 110 - 230 V ?10% 50/60Hz
Operation Range Up to 20m indoor when no obstacles
Application Indoor use only
Operation temperature 0 ~ 55 ?C
Motor Load max ?up to 1kW
Storage temperature ?10 ~ 80 ?C
Weight 50g
Housing ABS
Compliance C-Tick, EU standards EN 55022, EN 61000
 

Documentation

Fibaro Z-Wave Roller Shutter 3

Product Details

The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway. The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene. Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk) Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers. FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS

Product Details

The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway. The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene. Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk) Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers. FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS
Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information