REMOTEC Z-Wave Thermostat 500

$209.99

Availability: Out of Stock

The REMOTEC Z-Wave Thermostat ZTS-500 is a programmable electronic thermostat controller allowing you to keep your home at a comfortable temperature at all times.
A smart thermostat designed with the end user in mind. It combines compatibility with any Z-Wave certified controller or gateway with an incredibly simple and intuitive user interface.

  • Support 2 stage heat, 2 stage cool, 2 stage fan
  • 24Vac single & two stage conventional heating systems (gas/oil/electric)
  • Heat pump systems with up to two stages of heating (electric/gas)
  • Zoned forced air and zoned hot water (2 or 3 wire)
  • Millivolt systems (12-24Vac or DC source)
  • Can be controlled by android smartphones and iPhones (via home controller)
  • One or two stage cooling systems
  • Hybrid systems
  • Z-Wave Dual mode (FLiRS, Always Listening)

RemotecZTS500

Out of stock

SKU: DHS-HVAC-THR-REM500 Categories: , Tags: , , ,

Description

The?REMOTEC?Z-Wave Thermostat ZTS-500?is an intelligent, programmable thermostat controller with a blue ?display which is easy to read even in dimly lit areas.

This thermostat delivers permanent day and time settings that are even maintained during power outages. It offers the option to remotely control / check your room temperature via a smart phone or PC which is associated with your?Z-Wave Home controller.

For added convenience, the thermostat unit can be run using battery power or using power from your heating/cooling system, giving you the option of permanently eliminating battery changes.

This thermostat is compatible with a broad range of 24-volt heating and cooling systems, including both single-stage (cooling) and single and two-stage heating systems (non-heat pump), single-stage heat pumps, and heating-only or cooling-only systems. Uses standard thermostat connections:

To check compatibility with your heater or HVAC system please see what terminals are in use at your current heater or HVAC systems.

 

ZTS500terminals

Function Terminal
Cool changeover (heat pump) O
Heat changeover (heat pump) B
2nd Stage heater W2
1st Stage heater W1
Fan G
Compressor Y
24Vac Power for Cooling RC
24Vac Power for Heating RH
24Vac Common C

 

This product integrates with all Australian certified (921.42MHz) Z-Wave controllers including:

?Please Note:

  • This device is not compatible with electric baseboard heaters (120 to 240 volts). ?It is also not compatible with some multifunction 2-wired Japanese brand heaters and HVAC systems.
  • If you are not feeling confident with installing this thermostat get a heater/ac installer to do this job for you.
  • This thermostat is backed by a one-year limited warranty.

Product Support

Manuals:

??Z-Wave REMOTEC ZTS-500 Thermostat Manual (Size: 992KB)

Videos / YouTube:

??Z-Wave Remotec ZTS-500 Thermostat

Technical Specification

RF Protocol Z-Wave
RF Frequency 921.42Mhz – AU/NZ ?approved RF for Z-wave
Z-Wave device type Z-Wave Plus Thermostat, Routing slave
Relay Contact Voltage 24 VAC 50/60 Hz

Current: 1A Max (inductive)

Quick Comparison

SettingsREMOTEC Z-Wave Thermostat 500 removeFIBARO Z-Wave Button (Red) removeFIBARO Home Center 3 Lite removeAEOTEC Z-Wave USB Stick removeFIBARO Z-Wave Double Switch 2 removeFAKRO Z-Wave Wall Controller remove
Image
SKUDHS-HVAC-THR-REM500DHS-CON-SBUT-FIB-RDDHS-CON-HC3LITE-FIBDHS-CON-USB-AEODHS-LIT-SWW-FIB-022DHS-WIN-WC-FKR
Rating
Price$209.99$78.00$199.99$89.99$84.99$99.99
Stock

Out of stock

2 in stock

20 in stock

Out of stock

20 in stock

Out of stock

AvailabilityOut of stock2 in stock20 in stockOut of stock20 in stockOut of stock
Add to cart

Read more

Add to basket

Add to basket

Read more

Add to basket

Read more

DescriptionThe REMOTEC Z-Wave Thermostat ZTS-500 is a programmable electronic thermostat controller allowing you to keep your home at a comfortable temperature at all times. A smart thermostat designed with the end user in mind. It combines compatibility with any Z-Wave certified controller or gateway with an incredibly simple and intuitive user interface.
  • Support 2 stage heat, 2 stage cool, 2 stage fan
  • 24Vac single & two stage conventional heating systems (gas/oil/electric)
  • Heat pump systems with up to two stages of heating (electric/gas)
  • Zoned forced air and zoned hot water (2 or 3 wire)
  • Millivolt systems (12-24Vac or DC source)
  • Can be controlled by android smartphones and iPhones (via home controller)
  • One or two stage cooling systems
  • Hybrid systems
  • Z-Wave Dual mode (FLiRS, Always Listening)
RemotecZTS500
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
  • Completely wireless
  • Z-Wave Plus certified
  • Supports 6 different actions/scenes
  • Available in multiple colours (white, black, red, blue, yellow)
This new Fibaro home controller offers impressive hardware and integration options for installers and clients. This excellent Smart Home controller offers next generation hardware, including: COMMUNICATION TECHNOLOGY: Z-WAVE (700 series) NETWORK TECHNOLOGY: Wi-Fi 2.4GHz CPU: Single-Core ARM Cortex A7 900 MHz RAM MEMORY: 512 MB FLASH MEMORY: 4 GB eMMC The Fibaro Home Center 3 Lite is the perfect controller for small Home Automation projects, offering an excellent solution for smaller homes or apartments. The system is recommended for Smart Homes with up to 40 Z-Wave devices and 20 scenes. But, don't be mistaken by its size, the Fibaro HC3 Lite offers an affordable solution without having to compromise on quality. With this new system, you'll be able to automate a variety of solutions, including: Fibaro HC3 Lite SolutionsThe Aeotec Z-Stick (Gen 5) is a self-powered Z-Wave USB dongle with portable push-button inclusion for Z-Wave devices (independent from external power and host microprocessor). When attached to a host processor (PC etc), it becomes a Z-Wave communication device, which allows Z-Wave software to communicate with your Z-Wave devices. ZW090aThe new Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave wireless module which can control two circuits each with a maximum load of 6.5A per channel and 10A total load per circuit.
  • Control the ON-OFF function of two two independent circuits or appliances remotely or using a wall switch
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling
  • Latest generation Z-Wave 500 series chip
  • Z-Wave Plus certification
  • Very accurate energy measurement +/- 1 % for power above 5W
  • Supports secure mode (Z-Wave Network Security) encrypted with AES-128
  • No dry contacts - this is important. It means that the new FGS-223 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
The?FAKRO Z-Wave? ZWK10 Wall Controller??is a wall mounted multi-purpose remote that?s capable of operating up to 10 different FAKRO and Z-Wave? devices. For the simplest solution to managing your range of Z-Wave? and FAKRO devices, the?FAKRO Z-Wave ZWK10 Wall Controller has everything you need.
  • Easy to install and include into your existing Z-Wave? network setup
  • Integrates easily and operate FAKRO window openers as well as other Z-Wave? devices
  • Manage and operate multiple devices using just one controller
  • Can work as a Primary or Secondary controller
  • Setting Mode (Inclusion/Exclusion/Association/Learning/Shift)
Content

The?REMOTEC?Z-Wave Thermostat ZTS-500?is an intelligent, programmable thermostat controller with a blue ?display which is easy to read even in dimly lit areas.

This thermostat delivers permanent day and time settings that are even maintained during power outages. It offers the option to remotely control / check your room temperature via a smart phone or PC which is associated with your?Z-Wave Home controller.

For added convenience, the thermostat unit can be run using battery power or using power from your heating/cooling system, giving you the option of permanently eliminating battery changes.

This thermostat is compatible with a broad range of 24-volt heating and cooling systems, including both single-stage (cooling) and single and two-stage heating systems (non-heat pump), single-stage heat pumps, and heating-only or cooling-only systems. Uses standard thermostat connections:

To check compatibility with your heater or HVAC system please see what terminals are in use at your current heater or HVAC systems.   ZTS500terminals
Function Terminal
Cool changeover (heat pump) O
Heat changeover (heat pump) B
2nd Stage heater W2
1st Stage heater W1
Fan G
Compressor Y
24Vac Power for Cooling RC
24Vac Power for Heating RH
24Vac Common C
 

This product integrates with all Australian certified (921.42MHz) Z-Wave controllers including:

?Please Note:

  • This device is not compatible with electric baseboard heaters (120 to 240 volts). ?It is also not compatible with some multifunction 2-wired Japanese brand heaters and HVAC systems.
  • If you are not feeling confident with installing this thermostat get a heater/ac installer to do this job for you.
  • This thermostat is backed by a one-year limited warranty.

Product Support

Manuals:

??Z-Wave REMOTEC ZTS-500 Thermostat Manual (Size: 992KB)

Videos / YouTube:

??Z-Wave Remotec ZTS-500 Thermostat

Technical Specification

RF Protocol Z-Wave
RF Frequency 921.42Mhz - AU/NZ ?approved RF for Z-wave
Z-Wave device type Z-Wave Plus Thermostat, Routing slave
Relay Contact Voltage 24 VAC 50/60 Hz Current: 1A Max (inductive)

Product Details

The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway. The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene. Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk) Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers. FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS
Security: The FIBARO System will ensure the safety of you and your loved ones.
  • Smoke detection
  • Carbon monoxide detection
  • Flood detection
  • Operation as a wireless alarm system
  • Cooperation with the existing wired alarm system (eg SATEL) and security companies
  • Emergency door opening
  • Closing the roller shutters when you are away
Health: The FIBARO System will help you ensure the right conditions for your health.
  • Humidity control
  • Smart heating
  • Measurement of air quality and quality of PM2.5 and PM10 dust
  • Detection of hazardous gases
  • Control of ventilation and recuperation
  • Notifications in case of dangerous situations
Convenience: An intelligent home is primarily about increasing comfort and facilitating everyday activities.
  • Voice control
  • Remote home control from applications for phones, tablets and smart watches
  • Automatic scenarios - grouping devices, schedules and scenes
  • Control over devices with one button or remote control
  • Combining all elements of the house into one ecosystem
Sustainability: FIBARO will ensure that your home has a minimal impact on the surroundings and the environment.
  • Intelligent heating control leading to a reduction in the demand for heating media
  • Build awareness through the energy panel and measure current electricity consumption
  • The use of dimmers, thermostats or intelligent heads leads to significant energy savings
Savings: In the FIBARO system, your savings are very important.
  • The heating system is intelligently controlled through schedules and the presence of the household members
  • The use of dimmers and LED drivers leads to a reduction in bills
  • The ability to use scenarios and automation ensures that no devices will be redundantly used
Fibaro EcoSystem

Documentation

Fibaro Home Center 3 Lite User Manual  

Technical Specifications

Application Smaller houses (recommended up to 100 m2) and apartments
Number of Supported Devices Recommended up to 40 Z-Wave devices
Communication Technologies Z-Wave 700
Network Technologies Wi-Fi 2.4GHz
CPU Single-Core ARM Cortex A7 900 MHz
RAM 512MB
Flash Memory 4 GB eMMC
Possibilities of Automation LUA, block scenes, panels, schedules
Maximum number of scenes Recommended up to 20 scenes
IP Cameras Support 1 IP camera
Plugins and Quick Apps Support 5 plugins and 10 quick apps
Migration Mechanism No
Operating in Connected Gateways Mode Only SLAVE mode

Product Description

Create your own Z-Wave gateway. With Z-Stick Gen5 you?ll be able to create your own Z-Wave hub using readily available, and sometimes free, home automation software. You?ll benefit from a system that is locally hosted and cloud-free, whose features, security and privacy you can personally control, and you?ll be able to create your Z-Wave network at your own pace and within your own budget. Capable of controlling up to 232 different Z-Wave devices, including those that use the more advanced Z-Wave Plus, and able to run on both full-powered PCs and low powered PCs such as Raspberry Pi, Z-Stick Gen5 works with open source software such as Domoticz, Home Assistant, OpenHab, and OpenHab2 and also works with commercially available software such as Axial Control, Homeseer, Indigo for MacOS. For enhanced network performance and reduced downtime, Z-Stick Gen5 contains an inbuilt, rechargeable info-lithium battery.

Product Support

Works with Windows / Mac / Linux (including Raspberry Pi) to create a Z-Wave gateway for control of Z-Wave and Z-Wave Plus devices. Works with Windows / Mac / Linux (including Raspberry Pi) to create a Z-Wave gateway for control of Z-Wave and Z-Wave Plus devices. Tiny but powerful; 1.1 x 0.4 x 3.5 inches in size and capable of controlling up to 232 different Z-Wave devices. Can be used to upgrade the firmware of compatible Z-Wave Plus devices that can accept OTA / wireless firmware upgrades. Compatible with Z-Wave enabled home automation software including Home Assistant, Home Seer, Indigo 7, OpenHab, and OpenHab2. No software included. Manuals: ? Aeotec Z-Stick Gen5p product manual

Technical Specification

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Z-Wave device type
Z-Wave controller
Power
USB DC 4.75V to 5.25V
Operation Range
Up to 40m without obstacles
Application
Indoor use only
Operation temperature
0 ~ 55 ?C
Storage temperature
-10 ~ 80 ?C
Colour
White
Weight
20g
Housing
ABS
Dimensions
(LxWxH) 1.1 x 0.4 x 3.5 inches
Compliance
Z-Wave Plus certified
Warranty 12 Months

Product Details

The Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene. The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician. This Fibaro Fibaro Z-Wave Double Switch 2 requires 3-wire (including neutral) installation and works with an AC (230V) power supply. The Fibaro Z-Wave Double Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits. This product integrates with Australian certified (921.42 MHz) Z-Wave Controllers - Fibaro Home Center 2/Lite Note: It doesn't integrate with Vera gateways at this stage.

Configuring Z-Wave Devices:

Z-Wave devices often have several configurable parameters which you can change using Fibaro?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller. Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. Please check the maximum load before installing or operating. This installation must be done by a certified electrician in Australia and New Zealand. Before engaging an electrician, check that they provide an electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician.

Documentation

Fibaro Z-Wave Double Switch 2 Manual

Technical Specification

RF Protocol
Z-Wave
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Z?Wave device type
Z-Wave Switch, Routing Slave
Power
230V?? 10% 50/60 Hz
Operation Range
Up to 20 m indoors with no obstacles
Application
Indoor use only, up to?1.5kW resistive load per circuit
Operation temperature
0 ~ 55 ?C
Storage temperature
-10 ~ 80 ?C
Weight
50g
Housing
ABS
Compliance
EN 55015, EN 60669-2-1
Regulatory Compliance Mark
N5496
Dimensions
(LxWxH) 42mm x 37mm x 17mm

Product Description

The?FAKRO Z-Wave ZWK10 Wall Controller?is a smart device that enables you to manage several aspects of your home. Through radio communication processing, the FAKRO Z-Wave ZWK10 Wall Controller can interact with 10 devices at once, split into 5 different communication channels (2 devices for 1 channel). You can also categorize devices into 10 independent groups, based on their location and functionality around the home. The FAKRO Z-Wave ZWK10 Wall Controller can also be customized to operate as a PRIMARY controller for a single radio network, or as a SECONDARY controller for a pre-existing network. Configuring the controller to operate with each device is a simple process. Each device around the home is given a unique number (known as ?NodeID?) and calibrated to operate on a single Z-Wave? radio network (called ?HomeID?). Featuring a magnetic wall holder, the FAKRO Z-Wave ZWK10 Wall Controller can be mounted onto any location around the home for quick and easy access. This convenient, all-in-one solution can operate multiple FAKRO and Z-Wave related products. This product is compatible with:

Technical Specifications

RF Protocol
Z-Wave?
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Z?Wave device type
Z-Wave Controller
Status Indicator
LED Lights
Operation Range
Up to 40m without obstacles
Power
3V DC, Battery 2xAAA 1,5 V
Operation temperature
+5 ~ 45 ?C
Dimensions L x W x H
?80mm x 80mm x 30mm
Weight
180g
Housing
ABS
Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information