The?Z-WAVE.ME Z-Uno?is the perfect solution for DIY home automation systems. It is made for those who are limited by the existing choice of Z-Wave products and want to extend their smart homes with more sensors and actuators; connect LEDs, buttons, switches, motors or any low voltage sensor (including most compatible Arduino sensors) and write your own code in simplified C language to create your personalized Z-Wave device.
You can find many example projects and comprehensive tutorials on the?Z-WAVE.ME Z-Uno?website.
This product integrates with all Australian certified (921.42MHz) Z-Wave controllers including:
The?Z-WAVE.ME Z-Uno is the first (and only) easy to use developer board that allows you to create your own Z-Wave device!
Compatible with many Arduino peripherals
Z-Wave Plus certified
Programmable with simplified C language
Supports 1-Wire and I2C (software)
The new Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave wireless module which can control two circuits each with a maximum load of 6.5A per channel and 10A total load per circuit.
Control the ON-OFF function of two two independent circuits or appliances remotely or using a wall switch
Compatible with all Z-Wave networks
Acts as a repeater expanding your Z-Wave network
Wide range of compatibility with existing light fittings and does NOT require expensive cabling
Latest generation Z-Wave 500 series chip
Z-Wave Plus certification
Very accurate energy measurement +/- 1 % for power above 5W
Supports secure mode (Z-Wave Network Security) encrypted with AES-128
No dry contacts - this is important. It means that the new FGS-223 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
The Fibaro Z-Wave Single Switch 2 is a wireless Z-Wave module which can control appliances or lighting up to a maximum load of 2.0kW.
Control the ON-OFF function of a circuit remotely or using a wall switch
Compatible with all Z-Wave networks
Acts as a repeater expanding your Z-Wave network
Wide range of compatibility with existing light fittings and does NOT require expensive cabling
control loads up to 2kW (8A)
The main differences in the FGS-213 are:
Z-Wave Plus certification
Has power monitoring
230V powered only (this is the same as the FGS-212)
No dry contacts - this is important. It means that the new FGS-213 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
The?FAKRO Z-Wave? ZWMP Weather Module?is the primary component for monitoring outside weather conditions, along with offering compatibility with a variety of Z-Wave? home automation gateways. When installed in conjunction with the FAKRO ZRD Rain Sensor and FAKRO ZWD Wind Sensor, they can automatically close windows upon detecting wind or rainfall.
Easy to install and include into your existing Z-Wave? network setup
Compatible with the FAKRO ZRD Rain Sensor, FAKRO ZWD Wind Sensor, Thermostat and other external devices
Automatically sends closure requests to electronic shutters, windows and skylights upon detecting rain or wind
Can work as a Primary or Secondary controller
Easily programmable to communicate with compatible Z-Wave gateways
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
Completely wireless
Z-Wave Plus certified
Supports 6 different actions/scenes
Available in multiple colours (white, black, red, blue, yellow)
The?FAKRO Z-Wave W/Chain Winder 12V?is highly recommended for rooms with hard to reach windows. An automated system that controls ventilation openings can contribute significantly to maintaining a healthy and comfortable indoor climate. The European engineered, manufactured and certified FAKRO Z-Wave Chain Winder is the perfect solution to inaccessible windows and centralised managed buildings with automated natural ventilation.
Program in conjunction with the?FAKRO ZWMP Weather Module, for automated window closing upon detecting rain and windfall
Remote control functionality for ease of use
Overload protection
Easily programmable to communicate with compatible Z-Wave gateways
Automatic switch-off once fully extended
Content
Product Description
The?Z-WAVE.ME Z-Uno?is the perfect solution for DIY home automation systems. It is made for those who are limited by the existing choice of Z-Wave products and want to extend their smart homes with more sensors and actuators; connect LEDs, buttons, switches, motors or any low voltage sensor (including most compatible Arduino sensors) and write your own code in simplified C language to create your personalized Z-Wave device.
You can find many example projects and comprehensive tutorials on the?Z-WAVE.ME Z-Uno?website.
This product integrates with all Australian certified (921.42MHz) Z-Wave controllers including:
Binary/Multilevel switch,
Binary/Multilevel sensor, meter
Power
?USB 5V, external 3V, external 7-18V or battery
Hardware
28kB Flash memory for sketches
2 kB RAM
26 GPIO
1 USB (serial port)
64 kB EEPROM
Operation Range
Up to 30m indoors (with no obstacles)
Z-Wave Channel Types
Binary/Multilevel switch,
Binary/Multilevel sensor, meter
Operation temperature
10 ~ 40 ?C
Storage temperature
-10 ~ 60 ?C
Weight
10g
Board Dimensions
39mm x 20mm x 16mm
Antenna Length
86mm
Housing
N/A
Product Details
The Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.
The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.
This Fibaro Fibaro Z-Wave Double Switch 2 requires 3-wire (including neutral) installation and works with an AC (230V) power supply.
The Fibaro Z-Wave Double Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits.
This product integrates with Australian certified (921.42 MHz) Z-Wave Controllers - Fibaro Home Center 2/LiteNote: It doesn't integrate with Vera gateways at this stage.
Configuring Z-Wave Devices:
Z-Wave devices often have several configurable parameters which you can change using Fibaro?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller.
Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device.
Please check the maximum load before installing or operating.This installation must be done by a certified electrician in Australia and New Zealand.Before engaging an electrician, check that they provide an electrical compliance certificate.For a warranty claim, you have to provide an installation compliance certificate from your electrician.
Indoor use only, up to?1.5kW resistive load per circuit
Operation temperature
0 ~ 55 ?C
Storage temperature
-10 ~ 80 ?C
Weight
50g
Housing
ABS
Compliance
EN 55015, EN 60669-2-1
Regulatory Compliance Mark
N5496
Dimensions
(LxWxH) 42mm x 37mm x 17mm
Product Details
The Fibaro Z-Wave Single Switch 2 is a smart Z-Wave module capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.
The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.
This Fibaro Z-Wave Single Switch 2 requires 3-wire (including neutral) installation and works with an AC (110-230V) or DC (24-60V) power supply.
The Fibaro Z-Wave Single Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits.
This product integrates with all Australian certified (921.42MHz) Z-Wave controllers including:
Raspberry PI with RaZberry Card
Fibaro Home Controller 2/Lite
DHS Z-Wave Universal Remote Controller
DHS Z-Wave Mini Remote Controller
Configuring Z-Wave Devices
Z-Wave devices often have several configurable parameters which you can change using your Vera?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller.
Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section.
Please check the maximum load before installing or operating.This installation must be done by a certified electrician in Australia and New Zealand.Before engaging an electrician, check that they provide an electrical compliance certificate.For a warranty claim, you have to provide an installation compliance certificate from your electrician.
Providing a central unit for monitoring changing weather conditions, the?FAKRO Z-Wave ZWMP Weather Module?takes full advantage of the Z-Wave? system to allow for seamless inclusion into the home environment.
Including the ZWMP Weather Module into the Z-Wave system is simply using your Z-Wave Controller, in order for the device to be recognized. From there, each individual shutter/window or skylight installation can be programmed to interact with the ZWMP Weather Module, which will allow it to respond to changing weather conditions. The ZWMP Weather Module contains three digital inputs, which allows various external devices to be plugged in (ie. Rain and wind sensors, time switch, thermostat etc). With a working range of up to 40 meters, the ZWMP Weather Module can seamlessly interact with other Z-Wave devices around the household.
This product is compatible with:
The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway.
The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene.
Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk)
Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.
Technical Specifications
RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS
Product Description
For the most convenient use of your motorized window system, the FAKRO Z-Wave Chain Winder allows for remote accessibility anywhere around the home. Featuring an intuitive button prompt command process, this Z-Wave Chain Winder can easily be included in any existing Z-Wave system.
From skylights, awnings, tilted fixtures to bottom-hung/top-hung windows, the Chain Winder can be installed into many common window fittings. For the best results and consideration for your safety, always rely on a qualified electrician to install the Z-Wave Chain Winder device for you. The Chain Winder interacts with other Z-Wave products through a two-way radio communication system, which allows for uninterrupted operation on a consistent basis. The catch holder comfortably connects to the actuator chain for a strong and durable fitting, while the programming and manual operation buttons allow for easy inclusion with other Z-Wave devices.
Installation options:
1 Skylight or awning ? fixed mounting (inside the frame)
2 Skylight or awning ? with angle brackets (inside the frame)
3 Tilt or awning window ? fixed mounting (sash mounted)
4 Tilt or awning window ? with angle brackets (sash mounted)