Home Center 3 is the latest smart home management controller from Fibaro Group. Advanced technology within its components guarantees the highest stability and performance of the FIBARO System.
PRODUCT HIGHLIGHTS
Cutting-edge speed & stability,
4×1,2GHz processor, 2 GB RAM of memory,
Seamless integration with over 2000 third-party products operating in various technologies,
Fast configuration process,
Simple and complex automations, like Block Scenes, LUA events, Quick Apps,
Unquestionable, triple data security system,
Future-proof – lasts for years, maintaining top performance,
Home Center 3 is the latest smart home management controller from Fibaro Group. Advanced technology within its components guarantees the highest stability and performance of the FIBARO System.
Z-Wave chip 500 brings an exceptional number of hundreds of integrations with other brands products, which you can use while controlling electronics and household appliances, lighting, blinds, HVAC, alarm, monitoring or watering system – with just a single button, gesture or word.
Home Center 3 is the latest smart home management controller from Fibaro Group. Advanced technology within its components guarantees the highest stability and performance of the FIBARO System.
PRODUCT HIGHLIGHTS
Cutting-edge speed & stability,
4x1,2GHz processor, 2 GB RAM of memory,
Seamless integration with over 2000 third-party products operating in various technologies,
Fast configuration process,
Simple and complex automations, like Block Scenes, LUA events, Quick Apps,
Unquestionable, triple data security system,
Future-proof - lasts for years, maintaining top performance,
Ingenious and refined design.
FIBARO Swipe is a wireless, battery powered gesture-controlled pad that allows you to activate Z-Wave scenes or commands with a simple wave of the hand.
FIBARO Swipe has the appearance of a small tablet but instead of a touchscreen, it uses sophisticated motion identification technology to respond to six distinct hand gestures including four directional swipes (up, down, left, right), and two circular motions (left, right). A single gesture or a combination of gestures may be used ? for example, swipe ?down? to turn off the lights, ?up? to open your blinds. With four short swipes, the living room is transformed into a home theater! Swipe?s only limit is your imagination.
Z-Wave Plus certified contactless gesture control
May be used with wet or dirty hands ? e.g. turn on the lights in the kitchen or bathroom without getting the switches or wall dirty
Endless control possibilities ? e.g. wave goodbye to activate your ?going out? scene, swipe up to raise the volume on your sound system, swipe down to close difficult to reach skylight windows, reach out your hand from bed in the morning to activate your coffee machine
Endless placement possibilities ? e.g. visible on the dresser or a wall with your favourite family photos, or hidden away under the kitchen counter or coffee table
Powered by 4xAA batteries or Micro-USB giving you ultimate flexibility
Available in black or white
The Fibaro Z-Wave Single Switch 2 is a wireless Z-Wave module which can control appliances or lighting up to a maximum load of 2.0kW.
Control the ON-OFF function of a circuit remotely or using a wall switch
Compatible with all Z-Wave networks
Acts as a repeater expanding your Z-Wave network
Wide range of compatibility with existing light fittings and does NOT require expensive cabling
control loads up to 2kW (8A)
The main differences in the FGS-213 are:
Z-Wave Plus certification
Has power monitoring
230V powered only (this is the same as the FGS-212)
No dry contacts - this is important. It means that the new FGS-213 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
Range Extender 6.
The Range Extender 6 keeps it reliable. We all know how annoying weak wireless signals can be. Weak WiFi and poor phone signals are frustrating. Imagine if your smart home was also plagued by weak wireless signals and the same frustrations? Your smart home would not be very smart. The Range Extender 6 from Aeotec ensures that your connected home stays connected. It intelligently listens to the commands and reports that your Z-Wave network sends, actively capturing weak signals and then amplifying and repeating them.
The FIBARO Z-Wave RGBW Controller 2 is a wireless controller which enables you to manage your LED strips and halogen lights.
Wirelessly control LEDs with an unlimited range of colour options
Monitors energy usage
Four analogue sensor inputs
Four dimmer channels
Acts as a repeater expanding your Z-Wave network
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
Completely wireless
Z-Wave Plus certified
Supports 6 different actions/scenes
Available in multiple colours (white, black, red, blue, yellow)
Content
Product Details
Home Center 3 is the latest smart home management controller from Fibaro Group. Advanced technology within its components guarantees the highest stability and performance of the FIBARO System.
Z-Wave chip 500 brings an exceptional number of hundreds of integrations with other brands products, which you can use while controlling electronics and household appliances, lighting, blinds, HVAC, alarm, monitoring or watering system - with just a single button, gesture or word.
View the full presentation here.
Aditional protocols will be enabled later this year:
The FIBARO Swipe is equipped with the most precise 3D motion detecting sensor of its kind, which ensures flawless recognition of the performed gestures. It presents a new and innovative way of controlling home automation devices in an intuitive and user friendly way.
The magic of Swipe means you can position it in less conventional places as it will work through solid surfaces, like under a desk or behind a wall. And when displayed, Swipe can be used as a beautifully designed picture frame allowing you to easily change photos whenever you want through a simple to remove front panel. A special gesture controlled menu also allows you to add/remove or reset the device without dismantling it.
With the endless possibilities of a gesture, Swipe is a perfect solution for the elderly and disabled, or people who find technology difficult to learn. Show them how to turn on the heating or ventilate the room without even getting up from the chair.
Swipe needn?t be limited to the home either. Use it in the workplace to help you make the office as comfortable as the home. Control blinds, lights or a projector ? all with a wave of your hand.
FIBARO Swipe features the latest Z-Wave 500 series chip for improved wireless range, security and data transfer rates. Please note: Currently integrates with Australian Z-Wave certified (921.42MHz) Fibaro Home Center 2/Lite controllers only.
Installation
Place the Swipe onto its holder.
Place the Swipe within the direct range of your Z-Wave controller.
Plug the power source into the micro-USB port if required.
Set the main controller in (security/non-security) add mode (see the controller?s manual).
Move and hold your hand close to the center of the pad.
If the device is battery powered, high pitched beep will signal exiting the Standby Mode.
Loud sound sequence will confirm entering the menu, keep holding your hand.
After hearing two short beeps (green indicator colour), withdraw the hand and perform swiping up gesture to confirm selection (two beeps will confirm validity).
Wait for the adding process to end.
Successful adding will be confirmed by the Z-Wave controller?s message and 3 short beeps (green visual indicator colour).
The Fibaro Z-Wave Single Switch 2 is a smart Z-Wave module capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.
The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.
This Fibaro Z-Wave Single Switch 2 requires 3-wire (including neutral) installation and works with an AC (110-230V) or DC (24-60V) power supply.
The Fibaro Z-Wave Single Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits.
This product integrates with all Australian certified (921.42MHz) Z-Wave controllers including:
Raspberry PI with RaZberry Card
Fibaro Home Controller 2/Lite
DHS Z-Wave Universal Remote Controller
DHS Z-Wave Mini Remote Controller
Configuring Z-Wave Devices
Z-Wave devices often have several configurable parameters which you can change using your Vera?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller.
Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section.
Please check the maximum load before installing or operating.This installation must be done by a certified electrician in Australia and New Zealand.Before engaging an electrician, check that they provide an electrical compliance certificate.For a warranty claim, you have to provide an installation compliance certificate from your electrician.
Repeats wireless signals.
Repeats wireless signals.For your smart home to be perfect, its wireless signals need to be reliable. Range Extender 6 captures weak or slow signals and efficiently repeats them on to the rest of your Z-Wave network.
Amplifies wireless signals.
Amplifies wireless signals.Not only does Range Extender 6 accurately repeat Z-Wave signals, it amplifies them too and helps improve the reliability and accuracy of your Z-Wave network.
Big on impact.?Small in size.
Range Extender 6 is a power-outlet friendly device, designed to be as small and as compact as possible without compromising on performance. so that it doesn?t block neighbouring power outlets.
The FIBARO Z-Wave RGBW Controller 2 is a one of a kind, advanced wireless 4-colour LED strip controller. Apart from the traditional RGB channels it also supports the white light channel which allows you to add pastel colours to your lighting decorations.
The FIBARO Z-Wave RGBW Controller 2 also has four analogue inputs supporting any type of Fibaro sensor (e.g. light sensors, wind sensors, pressure sensors and potentiometers operating between 0-10V). This smart feature allows you to use your lighting as a warning for certain events. You could, for example, set your RGB garden lights to turn red and flicker when one of your security sensors is triggered, alerting your neighbours to the intruder and allowing them to notify the proper authorities.
This device has four output channels which means that you can connect and independently control up to four light sources. The FIBARO Z-Wave RGBW Controller 2 also allows you to monitor the energy consumed by the LED strips. Each of the four channels can be monitored independently providing you with all the information you need to minimise your energy bills.
The FIBARO Z-Wave RGBW Controller 2 can control:
12 / 24V DC powered RGB strips
12 / 24V DC powered RGBW strips
12 / 24V DC powered LED strips, bulbs, etc
12 / 24V DC powered halogen lights
12 / 24V DC powered low output power fans
Note: Power supply is not included.
This product integrates with all Australian certified (921.42 MHz) Z-Wave controllers including:
Fibaro Home Center 3/Lite
Fibaro Yubii Home
Configuring Z-Wave Devices:
Z-Wave devices often have several configurable parameters which you can change using your Vera?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active for or the type of manual switch connected to a Z-Wave light controller.
Every available configurable parameter is listed in your device?s user manual. In most cases your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section.
Please check the maximum load before installing or operating.This device must be installed by a certified electrician.For all warranty claims, an electrical compliance certificate from your electrician must be provided.
Technical Specifications
RF Protocol
Z?Wave
RF Frequency
921.42Mhz ? AU/NZ ?approved RF for Z?wave
Z?Wave device type
Z-Wave dimmer
Power
12V and 24V
Operation Range
Up to 50m outdoors, up to 30m indoors (depending on terrain and building structure)
Application
Controlled automatically by pre-set Fibaro devices or manually using any Z-Wave controller
The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway.
The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene.
Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk)
Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.
Manuals:
