The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway.
The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene.
Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk)
Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.
FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
Completely wireless
Z-Wave Plus certified
Supports 6 different actions/scenes
Available in multiple colours (white, black, red, blue, yellow)
Fibaro Flood Sensor is a universal, Z-Wave compatible, flood and temperature sensor. Device can be battery (ca. 2 years battery life) or VDC powered (12 or 24 VDC).
A flood alarm is sent to the Z-Wave network devices or additionally to any alarm system controller, through opening an NC contact.
The device has built in temperature sensor, monitoring the temperature of e.g. floor. Fibaro Flood Sensor is designed to be placed on the floor or on a wall with a flood sensor probe extended by a connected wire. The device has built in LED indicator and acoustic alarm. In addition, the sensor is equipped with a tilt sensor reporting tilt or movement to the main controller e.g. when someone has taken the Sensor from its original location. LED diode signals flood, operating mode or the Z-Wave network communication range. Fibaro Flood Sensor is sink-proof, which means it drifts on the water surface and keeps on sending alarm signals in case of substantial inundation of water.
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
Completely wireless
Z-Wave Plus certified
Supports 6 different actions/scenes
Available in multiple colours (white, black, red, blue, yellow)
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
Completely wireless
Z-Wave Plus certified
Supports 6 different actions/scenes
Available in multiple colours (white, black, red, blue, yellow)
The Aeotec Z-Stick (Gen 5) is a self-powered Z-Wave USB dongle with portable push-button inclusion for Z-Wave devices (independent from external power and host microprocessor). When attached to a host processor (PC etc), it becomes a Z-Wave communication device, which allows Z-Wave software to communicate with your Z-Wave devices.
The?QUBINO Single Switch (by GOAP) is a Z-Wave module for switching on/off the electrical device (e.g. light, fan, etc ...). The module can be controlled either through the Z-wave network or through the wall switch manually.
This module is designed to be mounted behind a traditional wall switch. The module measures the power consumption of load and supports the connection of the digital temperature sensor. It is designed to act as a repeater in order to improve the range and stability of the Z-Wave network.
Supported switches
The module supports mono-stable switches (push button) and bi-stable switches. The module is factory set to operate with bi-stable switches.
Content
Product Details
The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway.
The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene.
Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk)
Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.
Technical Specifications
RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS
Product Description
? Compatible with any Z-Wave network controller,
? May be connected to any alarm system (potential-free output terminal),
? Extremely easy installation - simply put on a surface prone to flooding,
? May be installed anywhere - flood sensor?s contacts extended with a wire,
? Battery or VDC powered. When connected to an external, VDC power source, the battery serves as an emergency power source,
? Theft protection - tilt is reported to the Z-Wave network or alarm system?s main controller,
? Two operating modes - flood/temperature sensor or just a temperature sensor.
Product Details
The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway.
The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene.
Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk)
Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.
Technical Specifications
RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS
Product Details
The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway.
The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene.
Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk)
Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.
Technical Specifications
RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS
Product Description
Create your own Z-Wave gateway. With Z-Stick Gen5 you?ll be able to create your own Z-Wave hub using readily available, and sometimes free, home automation software. You?ll benefit from a system that is locally hosted and cloud-free, whose features, security and privacy you can personally control, and you?ll be able to create your Z-Wave network at your own pace and within your own budget. Capable of controlling up to 232 different Z-Wave devices, including those that use the more advanced Z-Wave Plus, and able to run on both full-powered PCs and low powered PCs such as Raspberry Pi, Z-Stick Gen5 works with open source software such as Domoticz, Home Assistant, OpenHab, and OpenHab2 and also works with commercially available software such as Axial Control, Homeseer, Indigo for MacOS. For enhanced network performance and reduced downtime, Z-Stick Gen5 contains an inbuilt, rechargeable info-lithium battery.
Product Support
Works with Windows / Mac / Linux (including Raspberry Pi) to create a Z-Wave gateway for control of Z-Wave and Z-Wave Plus devices. Works with Windows / Mac / Linux (including Raspberry Pi) to create a Z-Wave gateway for control of Z-Wave and Z-Wave Plus devices.
Tiny but powerful; 1.1 x 0.4 x 3.5 inches in size and capable of controlling up to 232 different Z-Wave devices.
Can be used to upgrade the firmware of compatible Z-Wave Plus devices that can accept OTA / wireless firmware upgrades. Compatible with Z-Wave enabled home automation software including Home Assistant, Home Seer, Indigo 7, OpenHab, and OpenHab2.
No software included.
Manuals:? Aeotec Z-Stick Gen5p product manual
Technical Specification
RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Z-Wave device type
Z-Wave controller
Power
USB DC 4.75V to 5.25V
Operation Range
Up to 40m without obstacles
Application
Indoor use only
Operation temperature
0 ~ 55 ?C
Storage temperature
-10 ~ 80 ?C
Colour
White
Weight
20g
Housing
ABS
Dimensions
(LxWxH) 1.1 x 0.4 x 3.5 inches
Compliance
Z-Wave Plus certified
Warranty
12 Months
? Compatible with any Z-Wave Controller.
? Dimensions (W x H x D) 41,8 x 36,8 x 15,4mm
? Power monitoring accuracy P=5-50W, +/-3W; P?50W, +/-3%;
? Digital temperature sensor range (sensor must be ordered separately) -50 ~ 125?C
??Support for the connection of digital temperature sensor (optional part)
? 2 binary inputs offer the option to connect additional devices such as sensors, switches/pushbuttons, etc, ?
Note!Do not connect the module to loads exceeding recommended values. Connect the module only in accordance with the manual and diagrams below. Use only qualified electricians!