FIBARO Z-Wave Button (Green)

$78.00

Availability: In Stock

The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.

  • Completely wireless
  • Z-Wave Plus certified
  • Supports 6 different actions/scenes
  • Available in multiple colours (white, black, red, blue, yellow)

15 in stock

SKU: FGPB-101-5 Categories: , Tags: ,

Description

Product Details

The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway.

The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene.

FIBARO

Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk)

Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.

FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz – AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS

Quick Comparison

SettingsFIBARO Z-Wave Button (Green) removeDOME Z-Wave Water Sensor removeFIBARO Z-Wave Button (Red) removeFIBARO Z-Wave Dimmer 2 removeFIBARO Z-Wave Button (Blue) removeFIBARO Z-Wave Implant remove
Image
SKUFGPB-101-5DHS-SNS-FL-DOMDHS-CON-SBUT-FIB-RDDHS-LIT-DMW-FIB-02DHS-CON-SBUT-FIB-BUDHS-SNS-IMP-FIB
Rating
Price$78.00$54.99$78.00$84.99$78.00$69.99
Stock

15 in stock

10 in stock

2 in stock

20 in stock

2 in stock

Out of stock

Availability15 in stock10 in stock2 in stock20 in stock2 in stockOut of stock
Add to cart

Add to basket

Add to basket

Add to basket

Add to basket

Add to basket

Read more

DescriptionThe FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
  • Completely wireless
  • Z-Wave Plus certified
  • Supports 6 different actions/scenes
  • Available in multiple colours (white, black, red, blue, yellow)
The?DOME Z-Wave Water Sensor?is a compact, battery powered water leak sensor.?Dome Leak Sensor now officially works with Vera and Wink Z-Wave Gateways! The Dome Home Automation Wireless Z-Wave Leak Sensor with Remote Probe helps you cap leaks before they turn into gushes, so you can keep a lid on the amount of money you spend on water-related repairs. Use this battery-powered, smart-home leak detector anywhere you need to monitor water lines for potential problems. Its low-profile design allows you to hook it up underneath appliances and a 4-foot range remote sensor probe makes it easier to monitor water activity in hard-to-reach places like sump pumps. Toilets, refrigerators, water heaters, and other appliances and fixtures that require water lines can generate costly bills from ongoing small leaks and unexpected major breaks. The Dome Home Automation Water Resistant Leak Sensor keeps you up to date on the health of water lines leading in and out of these systems, and it sends you customized alerts via your connected Z-Wave Hub. Shut off main valves and take action when required. Use with most any Z-Wave Hub including: Vera, Wink, Fibaro HC2, Home Seer, SmartThings, Harmony and more (subject to local RF availability)?.
  • Built-in buzzer to alert those nearby
  • Includes remote sensor probe for tight spaces
  • Z-Wave Plus certified
  • Water resistant
DOME FS1
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
  • Completely wireless
  • Z-Wave Plus certified
  • Supports 6 different actions/scenes
  • Available in multiple colours (white, black, red, blue, yellow)
The Fibaro Z-Wave In-Wall Dimmer 2 (FGD-212) is the newest version of a popular wireless controller designed to operate behind a wall switch.
  • Control the level of illumination of your light remotely or using a manual button (in two and three way configurations)
  • Implemented algorithm of smart light source detection
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive re-wiring
  • Active power and energy metering functionality
  • Works with various types of manual buttons
  • Active element: semiconductor electronic switch
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
  • Completely wireless
  • Z-Wave Plus certified
  • Supports 6 different actions/scenes
  • Available in multiple colours (white, black, red, blue, yellow)
FIBARO Smart Implant allows to enhance the functionality of wired sensors and other devices by adding Z-Wave network communication. You can connect binary sensors, analog sensors, DS18B20 temperature sensors or DHT22 humidity and temperature sensor to report their readings to the Z-Wave controller. It can also control devices by opening/closing output contacts independently of the inputs.
Content

Product Details

The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway. The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene. Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk) Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers. FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS
The?DOME Z-Wave Water Sensor?is a Z-Wave Plus (500 series) compatible water sensor with a remote sensor probe for tight spaces. Simply place the device in a leak prone area and receive a notification from your Z-Wave network when a leak is detected allowing you to respond and prevent large scale water damage. Know when the sump pump fills up, BEFORE it overflows. Dangle the remote sensor probe in the tank to receive a notification and hear an alarm if the water level rises higher than it should. Use this device alongside a?DOME Wireless Water Valve?to automatically close your water valve when a leak is detected to greatly decrease the extent of water damage. Sleep easy knowing that your home is safe from water damage even when you are on vacation. This product is compatible with all Australian certified (921.42MHz) Z-Wave and Z-Wave Plus controllers including:

Product Support

??DOME Z-Wave Water Sensor User Manual ??Using the DOME Z-Wave Water Sensor with Vera

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Z-Wave device type
Z-Wave sensor
Power
1 x CR2 3.0V battery (included)
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
5 ~ 40 ?C
Storage temperature
-10 ~ 50 ?C
Weight
80g
Dimensions
67mm x 67mm x 26mm
Housing
ABS

Product Details

The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway. The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene. Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk) Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers. FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS
The Fibaro Z-Wave In-Wall Dimmer 2 is designed to operate with or without a neutral wire. It may be used as a switch in systems without a neutral wire. In the case of a 2-wire connection (no neutral), the Fibaro Z-Wave In-Wall Dimmer 2 may require a minimum load of 50W depending on the specifics of the connected load. When used with a Fibaro Dimmer Bypass 2 it may operate with any compatible (see below) load from 5W. Before committing to buy Fibaro Dimmer Bypass 2 please check if your load can be properly controlled by Fibaro Dimmer 2 without a bypass device. Do not connect this device to a power supply without a load. Only lighting devices may be connected to this device. As a dimmer it operates with the following loads:
  • 230V operated conventional incandescent (from 50W to 250W)
  • 230V operated halogen (from 50W to 200W)
  • 12 V operated ELV halogen lamps and dimmable LED lamps (with electronic transformers: Trailing and Leading-edge type) (from 50W to 200W)
  • 12V operated MLV halogen lamps (with ferromagnetic transformers) (from 50W to 225W)
  • Dimmable CFL tube lamps with electronic ballast only (from 50W to 200W)
As a switch it operates with the following loads:
  • Compact fluorescent lamps with electronic ballast
  • LED bulbs (power factor >0.7)
  • Fluorescent tube lamps with electronic ballast
Please note: For loads other than resistive do not exceed a 1.5A current. This product integrates with all Australian certified (921.42 MHz) Z-Wave and Z-Wave Plus controllers including:
  • Vera Plus/ Edge
  • Fibaro Home Center 2 / Lite
Please note: Do not mix the load type (e.g. LED and CFL or different types of transformers) as it will impede the proper operation of the dimmer. Doing so will void the dimmer's warranty. This product must be installed by a qualified electrician. Before engaging an electrician, check that they provide a warranty and electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician. PLEASE NOTE FOR THE INSTALLATIONS IN THE AREAS WHERE ELECTRICITY SUPPLIERS USE OFF-PEAK RIPPLE CONTROL SIGNALS: Electricity suppliers in particular areas of Australia such as NSW, QLD and some other places are injecting an off-peak ripple control signal using Zellweger equipment or similar onto their distribution networks in order to remotely control devices such as off-peak hot water systems and street lighting, although other areas within Australia also use this technology. Not all properties are affected by ripple control, so just because you might live in one of these areas, does not mean that you will have these problems. Ripple injection control systems work by superimposing coded control signals, commonly 750Hz or 1050Hz on the 50 Hz mains supply. Some electrical appliances such as fans, dimmers, toasters and LED lighting can be sensitive to this ripple control signal. The results could be audible buzzing noises from fans or flickering lights whenever the ripple control signals are present. Electricity suppliers are advising users to install appropriate ripple signal filters in such areas. The ripple signal filter is a tuned passive inline filter that completely eliminates the superimposed ripple injection control signal from the normal mains supply to produce a noise free filtered mains supply which can then be connected to the electrical appliances or light control systems. The ripple signal filter is specifically tuned to eliminate the ripple control signal frequency of 750Hz or 1050Hz. However, we can?t guarantee the ripple signal filter always will help you if you experiencing such issues. Please contact your local energy provider to get more information and proposed solutions for your electrical installation. If you are getting similar problems with your dimmers and fans and it?s not Ripple Control Signal and you are hearing the tones at random times of the day, your electrical supply may be affected by harmonics; a power fluctuation that is not part of the normal electricity supply or ripple control signal output. Harmonics are caused by interference created by other equipment on the network, such as inverter type air conditioners and switch mode power supplies for computers. The offending appliances may be in your home or other premises on the local power grid. If you are being affected by network harmonics, it may be of benefit to transfer the electricity supply to your premises to a different phase in the street. This is something you will need to discuss with your electrical company. We are strongly recommending for the areas we have mentioned above to run tests with only a few dimmers before committing for high volumes. If results are not fully OK you may use relays only instead of dimmers. Please note that our warranty for the faulty devices is not covering above mentioned conditions with your local electric grids. Please see affected with Ripple Signalling areas here:

QUEENSLAND

  • Only Southern Queensland (Energex) has Ripple Signalling.
  • The Frequency is 1050Hz.
  • The rest of Queensland (Ergon) does not have Ripple Signalling.

NSW

  • Energy Australia Full Supply Area
  • Energy Australia Sydney &Hunter Supply Area

Documentation

Fibaro Z-Wave In-Wall Dimmer 2 Manual

Technical Specifications

RF Protocol
Z-Wave
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Z?wave device type
Z-Wave multiple level dimmer, routing slave
Power Supply
220 - 240V?~ 50Hz
Operation Range
Up to 30m indoors (depending on building materials)
Application
Indoor use only
Operation temperature
0 ~ 35 ?C
Dimensions (L x W x H)
42.5mm x 38.25mm x 20.3mm
Weight
30g
Operational Current
0.25 - 1.1A
Compliance
RCM E3606
Dimming type compatibility
Leading and Trailing Edge

Product Details

The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway. The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene. Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk) Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers. FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS

Product Description

Supports Z-Wave network Security Modes: S0 with AES-128 encryption and S2 Authenticated with PRNG-based encryption. Works as a Z-Wave signal repeater. Allows for connecting sensors: 6 DS18B20 sensors, 1 DHT sensor, 2 2-wire analog sensor, 2 3-wire analog sensor, 2 binary sensors. Built-in temperature sensor. This product works with : Fibaro Home Controller 3/2/Lite Please note: THE DEVICE IS NOT COMPATIBLE WITH VERA HOME CONTROLLERS Before installation Connect only in accordance with one of the diagrams, The device is powered with secure voltage; nevertheless, the user should be extra careful or should commission the installation to a qualified person, Do not connect devices that are not compliant with the specification, Do not connect other sensors than DS18B20 or DHT22 to SP and SD terminals, Do not connect sensors to SP and SD terminals with wires longer than 3 meters, Do not load the device outputs with a current exceeding 150mA, Every connected device should be compliant with the relevant safety standards, Unused lines should be left insulated. Tips for arranging the antenna: Locate the antenna as far from metal elements as possible (connecting wires, bracket rings, etc.) in order to prevent interferences, Metal surfaces in the direct vicinity of the antenna (e.g. flush mounted metal boxes, metal door frames) may impair signal reception! Do not cut or shorten the antenna ? its length is perfectly matched to the band in which the system operates. Make sure no part of the antenna sticks out of the wall switch box.
Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information