The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway.
The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene.
Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk)
Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.
FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
Completely wireless
Z-Wave Plus certified
Supports 6 different actions/scenes
Available in multiple colours (white, black, red, blue, yellow)
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
Completely wireless
Z-Wave Plus certified
Supports 6 different actions/scenes
Available in multiple colours (white, black, red, blue, yellow)
The new Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave wireless module which can control two circuits each with a maximum load of 6.5A per channel and 10A total load per circuit.
Control the ON-OFF function of two two independent circuits or appliances remotely or using a wall switch
Compatible with all Z-Wave networks
Acts as a repeater expanding your Z-Wave network
Wide range of compatibility with existing light fittings and does NOT require expensive cabling
Latest generation Z-Wave 500 series chip
Z-Wave Plus certification
Very accurate energy measurement +/- 1 % for power above 5W
Supports secure mode (Z-Wave Network Security) encrypted with AES-128
No dry contacts - this is important. It means that the new FGS-223 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
Home Center 3 is the latest smart home management controller from Fibaro Group. Advanced technology within its components guarantees the highest stability and performance of the FIBARO System.
PRODUCT HIGHLIGHTS
Cutting-edge speed & stability,
4x1,2GHz processor, 2 GB RAM of memory,
Seamless integration with over 2000 third-party products operating in various technologies,
Fast configuration process,
Simple and complex automations, like Block Scenes, LUA events, Quick Apps,
Unquestionable, triple data security system,
Future-proof - lasts for years, maintaining top performance,
Ingenious and refined design.
This new Fibaro home controller offers impressive hardware and integration options for installers and clients. This excellent Smart Home controller offers next generation hardware, including:
COMMUNICATION TECHNOLOGY: Z-WAVE (700 series)
NETWORK TECHNOLOGY: Wi-Fi 2.4GHz
CPU: Single-Core ARM Cortex A7 900 MHz
RAM MEMORY: 512 MB
FLASH MEMORY: 4 GB eMMC
The Fibaro Home Center 3 Lite is the perfect controller for small Home Automation projects, offering an excellent solution for smaller homes or apartments. The system is recommended for Smart Homes with up to 40 Z-Wave devices and 20 scenes. But, don't be mistaken by its size, the Fibaro HC3 Lite offers an affordable solution without having to compromise on quality. With this new system, you'll be able to automate a variety of solutions, including:
FIBARO Swipe is a wireless, battery powered gesture-controlled pad that allows you to activate Z-Wave scenes or commands with a simple wave of the hand.
FIBARO Swipe has the appearance of a small tablet but instead of a touchscreen, it uses sophisticated motion identification technology to respond to six distinct hand gestures including four directional swipes (up, down, left, right), and two circular motions (left, right). A single gesture or a combination of gestures may be used ? for example, swipe ?down? to turn off the lights, ?up? to open your blinds. With four short swipes, the living room is transformed into a home theater! Swipe?s only limit is your imagination.
Z-Wave Plus certified contactless gesture control
May be used with wet or dirty hands ? e.g. turn on the lights in the kitchen or bathroom without getting the switches or wall dirty
Endless control possibilities ? e.g. wave goodbye to activate your ?going out? scene, swipe up to raise the volume on your sound system, swipe down to close difficult to reach skylight windows, reach out your hand from bed in the morning to activate your coffee machine
Endless placement possibilities ? e.g. visible on the dresser or a wall with your favourite family photos, or hidden away under the kitchen counter or coffee table
Powered by 4xAA batteries or Micro-USB giving you ultimate flexibility
Available in black or white
Content
Product Details
The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway.
The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene.
Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk)
Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.
Technical Specifications
RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS
Product Details
The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway.
The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene.
Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk)
Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.
Technical Specifications
RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS
Product Details
The Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.
The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.
This Fibaro Fibaro Z-Wave Double Switch 2 requires 3-wire (including neutral) installation and works with an AC (230V) power supply.
The Fibaro Z-Wave Double Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits.
This product integrates with Australian certified (921.42 MHz) Z-Wave Controllers - Fibaro Home Center 2/LiteNote: It doesn't integrate with Vera gateways at this stage.
Configuring Z-Wave Devices:
Z-Wave devices often have several configurable parameters which you can change using Fibaro?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller.
Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device.
Please check the maximum load before installing or operating.This installation must be done by a certified electrician in Australia and New Zealand.Before engaging an electrician, check that they provide an electrical compliance certificate.For a warranty claim, you have to provide an installation compliance certificate from your electrician.
Indoor use only, up to?1.5kW resistive load per circuit
Operation temperature
0 ~ 55 ?C
Storage temperature
-10 ~ 80 ?C
Weight
50g
Housing
ABS
Compliance
EN 55015, EN 60669-2-1
Regulatory Compliance Mark
N5496
Dimensions
(LxWxH) 42mm x 37mm x 17mm
Product Details
Home Center 3 is the latest smart home management controller from Fibaro Group. Advanced technology within its components guarantees the highest stability and performance of the FIBARO System.
Z-Wave chip 500 brings an exceptional number of hundreds of integrations with other brands products, which you can use while controlling electronics and household appliances, lighting, blinds, HVAC, alarm, monitoring or watering system - with just a single button, gesture or word.
View the full presentation here.
Aditional protocols will be enabled later this year:
Smaller houses (recommended up to 100 m2) and apartments
Number of Supported Devices
Recommended up to 40 Z-Wave devices
Communication Technologies
Z-Wave 700
Network Technologies
Wi-Fi 2.4GHz
CPU
Single-Core ARM Cortex A7 900 MHz
RAM
512MB
Flash Memory
4 GB eMMC
Possibilities of Automation
LUA, block scenes, panels, schedules
Maximum number of scenes
Recommended up to 20 scenes
IP Cameras Support
1 IP camera
Plugins and Quick Apps Support
5 plugins and 10 quick apps
Migration Mechanism
No
Operating in Connected Gateways Mode
Only SLAVE mode
Product Details
The FIBARO Swipe is equipped with the most precise 3D motion detecting sensor of its kind, which ensures flawless recognition of the performed gestures. It presents a new and innovative way of controlling home automation devices in an intuitive and user friendly way.
The magic of Swipe means you can position it in less conventional places as it will work through solid surfaces, like under a desk or behind a wall. And when displayed, Swipe can be used as a beautifully designed picture frame allowing you to easily change photos whenever you want through a simple to remove front panel. A special gesture controlled menu also allows you to add/remove or reset the device without dismantling it.
With the endless possibilities of a gesture, Swipe is a perfect solution for the elderly and disabled, or people who find technology difficult to learn. Show them how to turn on the heating or ventilate the room without even getting up from the chair.
Swipe needn?t be limited to the home either. Use it in the workplace to help you make the office as comfortable as the home. Control blinds, lights or a projector ? all with a wave of your hand.
FIBARO Swipe features the latest Z-Wave 500 series chip for improved wireless range, security and data transfer rates. Please note: Currently integrates with Australian Z-Wave certified (921.42MHz) Fibaro Home Center 2/Lite controllers only.
Installation
Place the Swipe onto its holder.
Place the Swipe within the direct range of your Z-Wave controller.
Plug the power source into the micro-USB port if required.
Set the main controller in (security/non-security) add mode (see the controller?s manual).
Move and hold your hand close to the center of the pad.
If the device is battery powered, high pitched beep will signal exiting the Standby Mode.
Loud sound sequence will confirm entering the menu, keep holding your hand.
After hearing two short beeps (green indicator colour), withdraw the hand and perform swiping up gesture to confirm selection (two beeps will confirm validity).
Wait for the adding process to end.
Successful adding will be confirmed by the Z-Wave controller?s message and 3 short beeps (green visual indicator colour).