AEOTEC WallMote Double

 

$108.00

Availability: Out of Stock

On any wall.

WallMote is the wall switch that you can install anywhere. Wirelessly.
Whatever the room, whatever the wall, WallMote is perfect. The wireless Z-Wave wall switch that you can place anywhere, on any wall, with as little as double-sided tape. Unpack it. Stick it. Charge it. Control is just a tap away.

ZW120a

Simple to install.

WallMote is the wall switch for anywhere because it is simple to install. Mounting it requires just two steps.

Attach the mounting plate.
WallMote’s mounting plate affixes to any wall or surface using custom mounting tape. Peel. Stick. Done.

Attach WallMote.
WallMote is attractive. Literally. Place it in front of the mounting plate, and it will magnetically attach.

Out of stock

SKU: DHS-CON-SCON-AEO-02 Categories: , Tags: , ,

Description

Product Description

Control on tap.

Control one Z-Wave device. Control many. And all with a single tap.
There is simplicity in tapping touch glass. smartphones proved it. There is power too. Each of WallMote’s buttons can be programmed to control one Z-Wave device or many. Meaning that a single tap on its smooth surface can change a single light, a whole room, or your whole home. Tap good morning. Tap good night. Tap all the moments in between.
Tap. Control.

ZW120c

wallmote mountwallmote engineeringwallmote glass

Control a light. Control a room. Control a home.Control a light. Control a room. Control a home.
Because WallMote communicates directly with your Z-Wave gateway, it can be used to control anything that your gateway can. Even things that are not Z-Wave. Smart lighting from Philips Hue? Check. Connected music from Sonos? Easy. If it is connected to your gateway, simply add it to a scene that WallMote can control and it is on top.

ZW120b

Wireless switch.
To be used anywhere in your home, WallMote and WallMote Quad need to be more than wireless. They need to be impressively wireless. Both switches offer a fine-tuned antenna capable of communicating over an open range of over 150 metres.
Secure switch.
Technology changes, now your wall switches change with it. WallMote and WallMote Quad are cutting-edge today and will be cutting-edge tomorrow. They are both capable of receiving wireless firmware updates via Z-Wave Plus so that they are always up to date.
Subtle switch.
Not just portable, but perfectly balanced. The minimalist design of both WallMote and WallMote Quad measures just 7.7cm wide and a slender 1.9cm deep
Simple recharging.
Battery powered but without the need to ever change a battery, WallMote and WallMote Quad are both powered by a rechargeable lithium battery designed for smartphones. It recharges just like a smartphone too via the provided micro USB cable.
Haptic feedback.
It is capable of controlling your whole home, so you may not even be present to see things change when you press WallMote’s touch glass. But you will feel the change. WallMote’s haptic engine confirms your every action via a click sensation.
Gen5 built in.
WallMote and WallMote Quad are part of Aeotec’s Gen5 range of Z-Wave devices. Built upon the latest version of Z-Wave- Z-Wave Plus – cutting-edge performance and security is crafted into Z-Wave’s most advanced battery-powered wall switch.

Product Support

Works with VeraAeotec Door Window Sensor 6 and Vera

Manuals

⇒  Aeotec WallMote product manual

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz – AU/NZ  approved RF for Z-wave
Z‐Wave device type
Multilevel controller
Power
Rechargeable Lithium-ion
Operation Range
Up to 40m without obstacles
Application
Indoor use only
Operation temperature
0 ~ 55 °C
Storage temperature
-10 ~ 80 °C
Color
White
Weight
100g
Housing
ABS
Dimensions
(LxWxH) 72mm x 72mm x 9mm
Compliance
Z-Wave Plus certified
Warranty 12 Months

Quick Comparison

SettingsAEOTEC WallMote Double removeAEOTEC MultiSensor Recessor removeAEOTEC Range Extender removeAEOTEC Multisensor 6 removeFIBARO Dimmer Bypass 2 removeAeotec SmartThings Motion remove
Image
SKUDHS-CON-SCON-AEO-02DHS-SNS-MS-AEO-RECDHS-CON-REXT-AEODHS-SNS-MS-AEODHS-LIT-BPASS-FIB-2AE-GP-AEOMPSEU
Rating
Price$108.00$24.99$68.99$79.99$19.99$54.99
Stock

Out of stock

12 in stock

1 in stock

12 in stock

20 in stock

1 in stock

AvailabilityOut of stock12 in stock1 in stock12 in stock20 in stock1 in stock
Add to cart

Read more

Add to basket

Add to basket

Add to basket

Add to basket

Add to basket

DescriptionOn any wall. WallMote is the wall switch that you can install anywhere. Wirelessly. Whatever the room, whatever the wall, WallMote is perfect. The wireless Z-Wave wall switch that you can place anywhere, on any wall, with as little as double-sided tape. Unpack it. Stick it. Charge it. Control is just a tap away. ZW120a Simple to install. WallMote is the wall switch for anywhere because it is simple to install. Mounting it requires just two steps. Attach the mounting plate. WallMote’s mounting plate affixes to any wall or surface using custom mounting tape. Peel. Stick. Done. Attach WallMote. WallMote is attractive. Literally. Place it in front of the mounting plate, and it will magnetically attach.Smart sensors. Invisible sensors. Smart sensors. A smart home should be intelligent and it should be invisible. Recessor is the realisation of that principle. It connects to the AEOTEC MultiSensor 6 and AEOTEC TriSensor allowing either to be seamlessly installed and recessed within a wall or ceiling space. Recessor makes Z-Wave multi-sensors subtle. ZW100a DSE010aDSE010cRange Extender 6. The Range Extender 6 keeps it reliable. We all know how annoying weak wireless signals can be. Weak WiFi and poor phone signals are frustrating. Imagine if your smart home was also plagued by weak wireless signals and the same frustrations? Your smart home would not be very smart. The Range Extender 6 from Aeotec ensures that your connected home stays connected. It intelligently listens to the commands and reports that your Z-Wave network sends, actively capturing weak signals and then amplifying and repeating them. ZW117cMotion for security. Motion for presence. Motion for management. The AETOEC MultiSensor 6 is perfect for more than just an intelligent security system. With a 5 metre range and a 120° field of view, the AEOTEC MultiSensor 6 captures motion data that can be used for everything from security to heating management to energy saving. Knowing if a room is occupied or a hall is being used is a powerful piece of data – the AEOTEC MultiSensor 6 makes your home automation system more powerful and more intelligent. ZW100aZW100a1The Fibaro Dimmer Bypass 2 (FGB-002) is a supplementary device to the Fibaro Z-Wave Dimmer 2 (FGD212 only) allowing it to control lamps that use at least 5W.
  • Easy to use and install
  • Supports low power lamps such as LEDs or energy saving compact fluorescent lamps
The Aeotec Multipurpose Works with SmartThings sensor enables you to receive alerts when a door or window is opened or closed and monitor the temperature in a room. In addition youll be able to set connected smart devices such as lights to power on and off as you open doors windows or cabinets - or when the temperature reaches a set level. The SmartThings app for iOS and Android also enables monitoring and control of your connected devices.
Content

Product Description

Control on tap. Control one Z-Wave device. Control many. And all with a single tap. There is simplicity in tapping touch glass. smartphones proved it. There is power too. Each of WallMote’s buttons can be programmed to control one Z-Wave device or many. Meaning that a single tap on its smooth surface can change a single light, a whole room, or your whole home. Tap good morning. Tap good night. Tap all the moments in between. Tap. Control. ZW120c wallmote mountwallmote engineeringwallmote glass Control a light. Control a room. Control a home.Control a light. Control a room. Control a home. Because WallMote communicates directly with your Z-Wave gateway, it can be used to control anything that your gateway can. Even things that are not Z-Wave. Smart lighting from Philips Hue? Check. Connected music from Sonos? Easy. If it is connected to your gateway, simply add it to a scene that WallMote can control and it is on top. ZW120b Wireless switch. To be used anywhere in your home, WallMote and WallMote Quad need to be more than wireless. They need to be impressively wireless. Both switches offer a fine-tuned antenna capable of communicating over an open range of over 150 metres. Secure switch. Technology changes, now your wall switches change with it. WallMote and WallMote Quad are cutting-edge today and will be cutting-edge tomorrow. They are both capable of receiving wireless firmware updates via Z-Wave Plus so that they are always up to date. Subtle switch. Not just portable, but perfectly balanced. The minimalist design of both WallMote and WallMote Quad measures just 7.7cm wide and a slender 1.9cm deep Simple recharging. Battery powered but without the need to ever change a battery, WallMote and WallMote Quad are both powered by a rechargeable lithium battery designed for smartphones. It recharges just like a smartphone too via the provided micro USB cable. Haptic feedback. It is capable of controlling your whole home, so you may not even be present to see things change when you press WallMote’s touch glass. But you will feel the change. WallMote’s haptic engine confirms your every action via a click sensation. Gen5 built in. WallMote and WallMote Quad are part of Aeotec’s Gen5 range of Z-Wave devices. Built upon the latest version of Z-Wave- Z-Wave Plus – cutting-edge performance and security is crafted into Z-Wave’s most advanced battery-powered wall switch.

Product Support

Works with VeraAeotec Door Window Sensor 6 and Vera

Manuals

⇒  Aeotec WallMote product manual

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z‐Wave device type
Multilevel controller
Power
Rechargeable Lithium-ion
Operation Range
Up to 40m without obstacles
Application
Indoor use only
Operation temperature
0 ~ 55 °C
Storage temperature
-10 ~ 80 °C
Color
White
Weight
100g
Housing
ABS
Dimensions
(LxWxH) 72mm x 72mm x 9mm
Compliance
Z-Wave Plus certified
Warranty 12 Months

Product Description

Still perfectly powered. Whichever power method you’re using with your multi-sensor, you can keep on using it with the AEOTEC Recessor. The AEOTEC Recessor has been designed to allow for each sensor’s batteries to still easily be changed, or for the AEOTEC MultiSensor 6’s optional power cable to be used if you prefer to power your sensor without batteries. aeotec multisensor 6 recessor a Still precise. The AEOTEC Recessor doesn’t just convert the AEOTEC MultiSensor 6 into a Z-Wave ceiling or beam sensor, it converts it into a precise sensor. Once recessed, your AEOTEC MultiSensor 6 can be angled up to 30º within the Recessor, fine tuning its measurements and readings to be just where you need them. aeotec multisensor 6 recessor

Product Support

The  perfect accessories. The AEOTEC MultiSensor 6 ships with 4 different accessories, each designed to make the installation of the sensor perfect for your home. ZW100d Recessor. Install the AEOTEC MultiSensor 6 in a ceiling or wall cavity with a recessor (sold separately) and just 12 mm will extrude. Features magnetic clasps for simple removal of the sensor. Mounting arm. (sold separately) Discrete and for corner installations, the mounting arm allows you to rotate MultiSensor 6 up to 360° and refine its field of view by up to 50°. USB cable. (sold separately) After 2 years you won’t have to change batteries if you power MultiSensor 6 via mains power using the provided 1.5 metre USB cable. Tape. Weighing only 74 grams, the AEOTEC MultiSensor 6 can be easily installed with just the provided double sided tape from 3M. Manuals: ⇒ Aeotec Multisensor 6 product manual

Technical Specification

Application
Indoor use only
Operation temperature
0 ~ 55 °C
Storage temperature
-10 ~ 80 °C
Colour
White
Weight
70g
Housing
ABS
Dimensions
(LxWxH) 86mm x 86mm x 43mm
Warranty 12 Months

Product Description

Repeats wireless signals. Repeats wireless signals.For your smart home to be perfect, its wireless signals need to be reliable. Range Extender 6 captures weak or slow signals and efficiently repeats them on to the rest of your Z-Wave network. Amplifies wireless signals. Amplifies wireless signals.Not only does Range Extender 6 accurately repeat Z-Wave signals, it amplifies them too and helps improve the reliability and accuracy of your Z-Wave network. Big on impact. Small in size. Range Extender 6 is a power-outlet friendly device, designed to be as small and as compact as possible without compromising on performance. so that it doesn’t block neighbouring power outlets.

Product Support

Works with VeraAeotec LED Bulb with Vera Manuals: ⇒  Aeotec Range Extender 6 product manuals

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z-Wave device type
Amplifier
Power
240V AC
Operation Range
Up to 150m without obstacles
Application
Indoor use only
Operation temperature
0 ~ 55 °C
Storage temperature
-10 ~ 80 °C
Colour
white
Weight
50g
Housing
ABS
Size
43mm x 40mm x 16mm
Compliance
Z-Wave Plus certified
Warranty 12 Months

Product Description

Motion sensor. Motion sensor. Motion for security. Motion for presence. Motion for management. The AEOTEC MultiSensor 6 is perfect for more than just an intelligent security system. With a 5 metre range and a 120° field of view, the AEOTEC MultiSensor 6 captures motion data that can be used for everything from security to heating management to energy saving. Knowing if a room is occupied or a hall is being used is a powerful piece of data – the AEOTEC MultiSensor 6 makes your home automation system more powerful and more intelligent. Temperature sensor. From motorised curtains and windows to fans and thermostats, there are a lot of ways that you can use Z-Wave to keep the temperature of a room absolutely perfect. The AEOTEC MultiSensor 6 provides the intelligence to do just that. Within each sensor is an incremental temperature sensor capable of accurately measuring between -10~50°C (14 to 122°F) and reporting temperature changes back to a smart home gateway. ZW100d1 Light sensor. Automated lighting is only as smart as the system that powers it. With the AEOTEC MultiSensor 6’s real-time, digital light sensor measuring the level of light in a room, your home control system will be able to intelligently maintain its ambience. From opening and closing curtains to setting lights to be the perfect level be it day or night, the AEOTEC MultiSensor 6 is the smarts behind smart lighting. ZW100d2 Humidity sensor. Spaces such as bathrooms and kitchens can be too humid, while some environments are often not humid enough. The AEOTEC MultiSensor 6 offers incremental monitoring of humidity ranging from 0% to 100%, allowing for the intelligent automation of fans, motorised windows, dehumidifiers and humidifiers. The AEOTEC MultiSensor 6 monitors your home on such an infinitesimal level so that your home management system can make your environment truly perfect. ZW100d3 Vibration sensor. It measures the environment it’s in, and it also measures itself. The AEOTEC MultiSensor 6 contains a seismic sensor capable of detecting and reporting event-based vibrations. Those slight changes can be used to protect the AEOTEC MultiSensor 6 – it’ll know if an intruder is tampering with it or if the sensor has accidentally moved from its place of installation. They’ll also be able to detect seismic activity within your home. ZW100d4 UV sensor. Perfectly managing an environment means understanding it perfectly. The AEOTEC MultiSensor 6 accurately measures ultraviolet light; the kind of light that causes everything from furniture bleaching to eye damage. Measured in line with the World Health Organisation’s UV Index, the AEOTEC MultiSensor 6 measures a room’s UV level so that an environment can be managed through curtains, shades and lighting, and so that health and property recommendations can be made.   ZW100d5

Product Support

The perfect sensor comes with the perfect accessories. The AEOTEC MultiSensor 6 has four different accessories, each designed to make the installation of the sensor perfect for your home. ZW100d Recessor. (sold separately) Install the AEOTEC MultiSensor 6 in a ceiling or wall cavity with a recessor (sold separately) and just 12 mm will extrude. Features magnetic clasps for simple removal of the sensor. Mounting arm. Discrete and for corner installations, the mounting arm allows you to rotate your AEOTEC MultiSensor 6 up to 360° and refine its field of view by up to 50°. USB cable. After 2 years you won’t have to change batteries if you power your AEOTEC MultiSensor 6 via mains power using the provided 1.5 metre USB cable. Tape. Weighing only 74 grams, the AEOTEC MultiSensor 6 can be easily installed with just the provided double-sided tape from 3M. Manuals: ⇒ Aeotec Multisensor 6 product manual Works with VeraAeotec LED Bulb with Vera copy

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z-Wave device type
Z-Wave multilevel sensor
Power
USB DC 4.75V to 5.25V
Operation Range
Up to 40m without obstacles
Application
Indoor use only
Operation temperature
0 ~ 55 °C
Storage temperature
-10 ~ 80 °C
Colour
White
Weight
74g
Housing
ABS
Dimensions
(LxWxH) 28mm x 28mm x 42mm
Compliance
Z-Wave Plus certified
Warranty 12 Months
The Fibaro Dimmer Bypass 2 is designed to support Fibaro Z-Wave In-Wall Dimmer 2 by enabling it to control and dim lights which draw a minimum of 5W (e.g LED lighting). It can be used in the case of connecting LED bulbs or energy-saving compact fluorescent lamps. Fibaro Dimmer Bypass 2 prevents flickering of the LED lights and glowing of the turned off compact fluorescent lamps. In the case of a 2-wire connection, Fibaro Dimmer Bypass 2 allows to reduce minimum power of load required by the Fibaro Dimmer 2 for correct operation. Fibaro Dimmer Bypass 2 provides powering of the Fibaro Dimmer 2 in case of controlling the low loads of minimum power down to 5VA (for cosφ>0.5) Please note: Fibaro Dimmer Bypass 2 can only be used with Fibaro Dimmer 2. This product must be installed by a qualified electrician. Before engaging an electrician, check that they provide a warranty and electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician.

Documentation

Fibaro Z-Wave In-Wall Dimmer 2 Manual Fibaro Z-Wave Dimmer 2 Bypass Manual

Technical Specifications

Application
Indoor use only
Operation temperature
0 ~ 35 °C
Power Consumption
less then 1.2W
Weight
35g
Power Supply
220 - 240 V ~ 50 Hz
Dimensions
(L x W x H) 31mm x 21.6mm x 13mm
Compliance
RoHS 2011/65/EU, LVD 2006/95/EU, EMC 2004/108
The Aeotec Multipurpose Works with SmartThings sensor enables you to receive alerts when a door or window is opened or closed and monitor the temperature in a room. In addition youll be able to set connected smart devices such as lights to power on and off as you open doors windows or cabinets - or when the temperature reaches a set level. The SmartThings app for iOS and Android also enables monitoring and control of your connected devices.
Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information