Dimming energy-saving lights is complicated ? there?s a lot of different technologies built into modern bulbs.
That?s why dimmed lights sometimes flicker or remain on ? power trickles through.?The?AEOTEC Dimmer Bypass?works with the?AEOTEC Nano Dimmer?to remove the signals from your power line that cause low-watt lightbulbs to flicker.
If you want to control low-voltage lighting that?uses less than 4 Watts?using an?AEOTEC Nano Dimmer?you will need to include the?AEOTEC Dimmer Bypass?in your installation to ensure the lights do not flicker.
There are a lot of different types of low-power light bulbs that your home may have; Bypass has been designed to work with most of them. It?s been designed to stop most bulbs from flickering including?static and dimmable LEDs and CFLs.
Product Support
Wiring diagram.
3-wire connection with neutral and bypass load.
2-wire connection without neutral and bypass load.
Stop dimmed lights flickering.
Dimming energy-saving lights is complicated ? there?s a lot of different technologies built into modern bulbs.
That?s why dimmed lights sometimes flicker or remain on ? power trickles through.?The?AEOTEC Dimmer Bypass?works with the?AEOTEC Nano Dimmer?to remove the signals from your power line that cause low-watt lightbulbs to flicker.
If you want to control low-voltage lighting that?uses less than 4 Watts?using an?AEOTEC Nano Dimmer?you will need to include the?AEOTEC Dimmer Bypass?in your installation to ensure the lights do not flicker.
Three different sensors built into the?AEOTEC TriSensor's?small finish.
A motion sensor to monitor presence in your rooms, a temperature sensor to manage its environment, and a light sensor to manage connected lighting and shutters.
The new Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave wireless module which can control two circuits each with a maximum load of 6.5A per channel and 10A total load per circuit.
Control the ON-OFF function of two two independent circuits or appliances remotely or using a wall switch
Compatible with all Z-Wave networks
Acts as a repeater expanding your Z-Wave network
Wide range of compatibility with existing light fittings and does NOT require expensive cabling
Latest generation Z-Wave 500 series chip
Z-Wave Plus certification
Very accurate energy measurement +/- 1 % for power above 5W
Supports secure mode (Z-Wave Network Security) encrypted with AES-128
No dry contacts - this is important. It means that the new FGS-223 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
The Fibaro Z-Wave In-Wall Dimmer 2 (FGD-212) is the newest version of a popular wireless controller designed to operate behind a wall switch.
Control the level of illumination of your light remotely or using a manual button (in two and three way configurations)
Implemented algorithm of smart light source detection
Acts as a repeater expanding your Z-Wave network
Wide range of compatibility with existing light fittings and does NOT require expensive re-wiring
Active power and energy metering functionality
Works with various types of manual buttons
Active element: semiconductor electronic switch
The?Fibaro Dimmer Bypass 2?(FGB-002)?is a?supplementary?device to the?Fibaro Z-Wave Dimmer 2 (FGD212 only) allowing it to control lamps that use at least 5W.
Easy to use and install
Supports low power lamps such as LEDs or?energy saving compact fluorescent lamps
The Aeotec Door/Window Sensor 7 is a Z-Wave Plus device for detecting if a door or window is opened or closed. Small, battery powered (included) and easily attached to virtually anything that opens or closes around your home. Door Window Sensor 7 also includes universal "dry contact" terminals allowing you to wire in other external sensors. Z-Wave Plus certified, the?AEOTEC Door/Window Sensor 7?is compatible with all certified Z-Wave gateways including Control4 (Z-Wave enabled), HomeSeer, Indigo for Mac, and Vera/Ezlo Edge/VeraPlus/VeraSecure/Athom Controllers.
It?s Aeotec's fastest sensor yet with 50% faster communication than other models. Its sensor?s enhanced sensitivity and use of Z-Wave S2 and Aeotec?s exclusive Spatial Intrusion Algorithm means that the Z-Wave wireless signals your smart home depends on are transmitted, received and processed instantly.
Maximised wireless range.
To be simple to install, it has to be wireless. To secure your home, its engineering has to be perfect. Door / Window Sensor 7 is powered by the speed enhancements that come from Z-Wave Plus and Z-Wave S2 enabling it to communicate wirelessly 50% faster and up to 67% further in real-world use.
Optimised battery life.
Wireless is convenient but having to change batteries too often is annoying. That?s why Door / Window Sensor 7 features a unique balance of hardware and software optimisations which allow it to use up to 66% less battery power to communicate via Z-Wave Plus. It?s German engineering at its very best.
Intelligent multi-sensor.
It's not just a security or an intelligence sensor - it's a 3-in-1 multipurpose sensor. Door / Window Sensor 7 features a unique layering of a contact sensor (reed switch), gyroscope and universal binary input sensor.
Secure security.
It drives your home?s security - so it needs to be secure. Door / Window Sensor 7 combines ECDH key exchange and AES-128 bit communication encryption to render man-in-the-middle and brute force hacking virtually impossible.
Content
Product Description
Compatible bulbs.
There are a lot of different types of low-power light bulbs that your home may have; Bypass has been designed to work with most of them. It?s been designed to stop most bulbs from flickering including?static and dimmable LEDs and CFLs.
Motion sensor
Motion sensor. Motion for security. Motion for presence. Motion for management. The?AEOTEC TriSensor?is perfect for more than just an intelligent security system. With a 7 metre range, the AEOTEC TriSensor?captures motion data that can be used for everything from security to heating management to energy saving. Knowing if a room is occupied or a hall is being used is a powerful piece of data.
The?AEOTEC TriSensor?makes your home automation system more powerful and more intelligent.
Temperature sensor.
From motorised curtains and windows to fans and thermostats, there are a lot of ways that you can use Z-Wave to keep the temperature of a room absolutely perfect. The?AEOTEC TriSensor?provides the intelligence to do just that. Within each sensor is an incremental temperature sensor capable of accurately measuring between -15~50 ?C and reporting those temperature changes back to a smart home gateway.
Light sensor.
Automated lighting is only as smart as the system that powers it. With the?AEOTEC TriSensor's digital light sensor measuring the level of light in a room, your home control system will be able to intelligently maintain its ambience. From opening and closing curtains to setting lights to be the perfect level be it day or night, the AEOTEC TriSensor?is the smarts behind smart lighting.
The perfect sensor comes with the perfect accessories. The?AEOTEC TriSensor?has three different accessories, each designed to make the installation of the sensor perfect for your home.
Place it anywhere.
Recessor.?(sold separately)
Install the?AEOTEC TriSensor?in a ceiling or wall cavity with a recessor (sold separately) and just 12 mm will extrude. Features magnetic clasps for simple removal of the sensor.
Mounting arm.
Discrete and for corner installations, the mounting arm allows you to rotate your?AEOTEC TriSensor to best ensure motion is detected when you want it to be.
Tape.
Weighing only 52 grams, the?AEOTEC TriSensor can be easily installed with just the provided double-sided tape from 3M.
The Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.
The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.
This Fibaro Fibaro Z-Wave Double Switch 2 requires 3-wire (including neutral) installation and works with an AC (230V) power supply.
The Fibaro Z-Wave Double Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits.
This product integrates with Australian certified (921.42 MHz) Z-Wave Controllers - Fibaro Home Center 2/LiteNote: It doesn't integrate with Vera gateways at this stage.
Configuring Z-Wave Devices:
Z-Wave devices often have several configurable parameters which you can change using Fibaro?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller.
Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device.
Please check the maximum load before installing or operating.This installation must be done by a certified electrician in Australia and New Zealand.Before engaging an electrician, check that they provide an electrical compliance certificate.For a warranty claim, you have to provide an installation compliance certificate from your electrician.
Indoor use only, up to?1.5kW resistive load per circuit
Operation temperature
0 ~ 55 ?C
Storage temperature
-10 ~ 80 ?C
Weight
50g
Housing
ABS
Compliance
EN 55015, EN 60669-2-1
Regulatory Compliance Mark
N5496
Dimensions
(LxWxH) 42mm x 37mm x 17mm
The Fibaro Z-Wave In-Wall Dimmer 2 is designed to operate with or without a neutral wire. It may be used as a switch in systems without a neutral wire.
In the case of a 2-wire connection (no neutral), the Fibaro Z-Wave In-Wall Dimmer 2 may require a minimum load of 50W depending on the specifics of the connected load.
When used with a Fibaro Dimmer Bypass 2 it may operate with any compatible (see below) load from 5W. Before committing to buy Fibaro Dimmer Bypass 2 please check if your load can be properly controlled by Fibaro Dimmer 2 without a bypass device.
Do not connect this device to a power supply without a load. Only lighting devices may be connected to this device.
As a dimmer it operates with the following loads:
230V operated conventional incandescent (from 50W to 250W)
230V operated halogen (from 50W to 200W)
12 V operated ELV halogen lamps and dimmable LED lamps (with electronic transformers: Trailing and Leading-edge type) (from 50W to 200W)
Dimmable CFL tube lamps with electronic ballast only (from 50W to 200W)
As a switch it operates with the following loads:
Compact fluorescent lamps with electronic ballast
LED bulbs (power factor >0.7)
Fluorescent tube lamps with electronic ballast
Please note: For loads other than resistive do not exceed a 1.5A current.
This product integrates with all Australian certified (921.42 MHz) Z-Wave and Z-Wave Plus controllers including:
Vera Plus/ Edge
Fibaro Home Center 2 / Lite
Please note: Do not mix the load type (e.g. LED and CFL or different types of transformers) as it will impede the proper operation of the dimmer. Doing so will void the dimmer's warranty.
This product must be installed by a qualified electrician.Before engaging an electrician, check that they provide a warranty and electrical compliance certificate.For a warranty claim, you have to provide an installation compliance certificate from your electrician.PLEASE NOTE FOR THE INSTALLATIONS IN THE AREAS WHERE ELECTRICITY SUPPLIERS USE OFF-PEAK RIPPLE CONTROL SIGNALS:
Electricity suppliers in particular areas of Australia such as NSW, QLD and some other places are injecting an off-peak ripple control signal using Zellweger equipment or similar onto their distribution networks in order to remotely control devices such as off-peak hot water systems and street lighting, although other areas within Australia also use this technology. Not all properties are affected by ripple control, so just because you might live in one of these areas, does not mean that you will have these problems.
Ripple injection control systems work by superimposing coded control signals, commonly 750Hz or 1050Hz on the 50 Hz mains supply.
Some electrical appliances such as fans, dimmers, toasters and LED lighting can be sensitive to this ripple control signal. The results could be audible buzzing noises from fans or flickering lights whenever the ripple control signals are present.
Electricity suppliers are advising users to install appropriate ripple signal filters in such areas.
The ripple signal filter is a tuned passive inline filter that completely eliminates the superimposed ripple injection control signal from the normal mains supply to produce a noise free filtered mains supply which can then be connected to the electrical appliances or light control systems. The ripple signal filter is specifically tuned to eliminate the ripple control signal frequency of 750Hz or 1050Hz.
However, we can?t guarantee the ripple signal filter always will help you if you experiencing such issues. Please contact your local energy provider to get more information and proposed solutions for your electrical installation.
If you are getting similar problems with your dimmers and fans and it?s not Ripple Control Signal and you are hearing the tones at random times of the day, your electrical supply may be affected by harmonics; a power fluctuation that is not part of the normal electricity supply or ripple control signal output.
Harmonics are caused by interference created by other equipment on the network, such as inverter type air conditioners and switch mode power supplies for computers.
The offending appliances may be in your home or other premises on the local power grid. If you are being affected by network harmonics, it may be of benefit to transfer the electricity supply to your premises to a different phase in the street. This is something you will need to discuss with your electrical company.
We are strongly recommending for the areas we have mentioned above to run tests with only a few dimmers before committing for high volumes. If results are not fully OK you may use relays only instead of dimmers.
Please note that our warranty for the faulty devices is not covering above mentioned conditions with your local electric grids.
Please see affected with Ripple Signalling areas here:
QUEENSLAND
Only Southern Queensland (Energex) has Ripple Signalling.
The Frequency is 1050Hz.
The rest of Queensland (Ergon) does not have Ripple Signalling.
Up to 30m indoors (depending on building materials)
Application
Indoor use only
Operation temperature
0 ~ 35 ?C
Dimensions (L x W x H)
42.5mm x 38.25mm x 20.3mm
Weight
30g
Operational Current
0.25 - 1.1A
Compliance
RCM E3606
Dimming type compatibility
Leading and Trailing Edge
The?Fibaro Dimmer Bypass 2?is designed to support?Fibaro Z-Wave In-Wall Dimmer 2 by enabling it to control and dim lights which draw a minimum of 5W (e.g LED lighting).
It can be used in the case of connecting LED bulbs or energy-saving compact fluorescent lamps. Fibaro Dimmer Bypass 2 prevents flickering of the LED lights and glowing of the turned off compact fluorescent lamps. In the case of a 2-wire connection, Fibaro Dimmer Bypass 2 allows to reduce minimum power of load required by the Fibaro Dimmer 2 for correct operation. Fibaro Dimmer Bypass 2 provides powering of the Fibaro Dimmer 2 in case of controlling the low loads of minimum power down to 5VA (for cos?>0.5)
Please note: Fibaro Dimmer Bypass 2 can only be used with Fibaro Dimmer 2.
This product must be installed by a qualified electrician.Before engaging an electrician, check that they provide a warranty and electrical compliance certificate.For a warranty claim, you have to provide an installation compliance certificate from your electrician.
Please read this and other device guides carefully. Failure to follow the recommendations set forth by Aeotec Limited may be dangerous or cause a violation of the law. The manufacturer, importer, distributor, and/or reseller will not be held responsible for any loss or damage resulting from not following any instructions in this guide or in other materials.
Keep product and batteries away from open flames and extreme heat. Avoid direct sunlight or heat exposure. Always remove all batteries from products that are being stored and not used. Batteries may damage the appliance if they leak. Do not use rechargeable batteries. Ensure correct polarity when inserting the batteries. Improper battery use may damage the product.
Door / Window Sensor 7 is intended for indoor use in dry locations only. Do not use in damp, moist, and/or wet locations.
It contains small parts; keep away from children.?
The sensor can be mounted either on the moving part or on the fixed part of a door or a window. Mounting can be accomplished either using the tape by peeling off the protection foil or using two screws with holes inside the battery compartment. If the tilt detection on a window (only normal windows, no roof windows) shall be used the sensor device must be placed on the moving part of the window and the magnet on the window frame.
Three different sensors built into the?AEOTEC TriSensor's?small finish.
A motion sensor to monitor presence in your rooms, a temperature sensor to manage its environment, and a light sensor to manage connected lighting and shutters.
It?s Aeotec's fastest sensor yet with 50% faster communication than other models. Its sensor?s enhanced sensitivity and use of Z-Wave S2 and Aeotec?s exclusive Spatial Intrusion Algorithm means that the Z-Wave wireless signals your smart home depends on are transmitted, received and processed instantly.
Maximised wireless range.
To be simple to install, it has to be wireless. To secure your home, its engineering has to be perfect. Door / Window Sensor 7 is powered by the speed enhancements that come from Z-Wave Plus and Z-Wave S2 enabling it to communicate wirelessly 50% faster and up to 67% further in real-world use.
Optimised battery life.
Wireless is convenient but having to change batteries too often is annoying. That?s why Door / Window Sensor 7 features a unique balance of hardware and software optimisations which allow it to use up to 66% less battery power to communicate via Z-Wave Plus. It?s German engineering at its very best.
Intelligent multi-sensor.
It's not just a security or an intelligence sensor - it's a 3-in-1 multipurpose sensor. Door / Window Sensor 7 features a unique layering of a contact sensor (reed switch), gyroscope and universal binary input sensor.
Secure security.
It drives your home?s security - so it needs to be secure. Door / Window Sensor 7 combines ECDH key exchange and AES-128 bit communication encryption to render man-in-the-middle and brute force hacking virtually impossible.
Recessor.?(
