The?Fibaro Dimmer Bypass 2?(FGB-002)?is a?supplementary?device to the?Fibaro Z-Wave Dimmer 2 (FGD212 only) allowing it to control lamps that use at least 5W.
Easy to use and install
Supports low power lamps such as LEDs or?energy saving compact fluorescent lamps
The?Fibaro Dimmer Bypass 2?is designed to support?Fibaro Z-Wave In-Wall Dimmer 2 by enabling it to control and dim lights which draw a minimum of 5W (e.g LED lighting).
It can be used in the case of connecting LED bulbs or energy-saving compact fluorescent lamps. Fibaro Dimmer Bypass 2 prevents flickering of the LED lights and glowing of the turned off compact fluorescent lamps. In the case of a 2-wire connection, Fibaro Dimmer Bypass 2 allows to reduce minimum power of load required by the Fibaro Dimmer 2 for correct operation. Fibaro Dimmer Bypass 2 provides powering of the Fibaro Dimmer 2 in case of controlling the low loads of minimum power down to 5VA (for cos?>0.5)
Please note: Fibaro Dimmer Bypass 2 can only be used with Fibaro Dimmer 2.
This product must be installed by a qualified electrician. Before engaging an electrician, check that they provide a warranty and electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician.
The?Fibaro Dimmer Bypass 2?(FGB-002)?is a?supplementary?device to the?Fibaro Z-Wave Dimmer 2 (FGD212 only) allowing it to control lamps that use at least 5W.
Easy to use and install
Supports low power lamps such as LEDs or?energy saving compact fluorescent lamps
Shelly Dimmer 2 WiFi-operated dimmer
Control a wide range of halogen lights, dimmable LED and ferromagnetic transformers from anywhere with the smallest WiFi-operated dimmer in the world ? Shelly Dimmer2 working without a neutral line.
Shelly Dimmer2
has an embedded webserver
has been designed for installation in a limited space, such as wall mounts, electrical control panels, etc.
can function as a standalone device, as an accessory to a home automation controller, or it may be used as another automation system's component
overload, and temperature protection
This product is approved for use in Australia but must be installed by a licensed electrician.
Shelly 1L Single wire WiFi-operated relay
Convert any existing wall switch into a smart switch without changing the wiring or running new cables with Shelly 1L. The first device in the world that is able to automate even the appliances wired with no neutral present. Thanks to its small size and wide range of voltage support, it's a real innovation!
NO NEUTRAL REQUIRED. Power and control your light, fan, or other appliances with only a live wire, no neutral required to be connected to the device.
OVERHEATING PROTECTION.?If the Shelly 1L reached high temperatures, it will switch OFF the output to protect itself and your home appliances.
MQTT ENABLED.?Easily integrate Shelly 1L to your existing home server using the MQTT or CoAP protocols
REST API.?Use the REST API to connect Shelly 1L to your existing home automation system.
HIGHLY COMPATIBLE. Compatible with Android, iOS, Amazon Alexa and Google Assistant. Control your appliance with your voice.
SUNRISE/SUNSET SCHEDULES. Shelly 1L can automatically follow the sunrise and sunset and control your lighting accordingly.
This product is approved for use in Australia but must be installed by a licensed electrician.
On any wall.
WallMote is the wall switch that you can install anywhere. Wirelessly.
Whatever the room, whatever the wall, WallMote is perfect. The wireless Z-Wave wall switch that you can place anywhere, on any wall, with as little as double-sided tape. Unpack it. Stick it. Charge it. Control is just a tap away.
Simple to install.
WallMote is the wall switch for anywhere because it is simple to install. Mounting it requires just two steps.
Attach the mounting plate.
WallMote?s mounting plate affixes to any wall or surface using custom mounting tape. Peel. Stick. Done.
Attach WallMote.
WallMote is attractive. Literally. Place it in front of the mounting plate, and it will magnetically attach.
The?QUBINO Single Switch (by GOAP) is a Z-Wave module for switching on/off the electrical device (e.g. light, fan, etc ...). The module can be controlled either through the Z-wave network or through the wall switch manually.
This module is designed to be mounted behind a traditional wall switch. The module measures the power consumption of load and supports the connection of the digital temperature sensor. It is designed to act as a repeater in order to improve the range and stability of the Z-Wave network.
Supported switches
The module supports mono-stable switches (push button) and bi-stable switches. The module is factory set to operate with bi-stable switches.
The FIBARO Z-Wave RGBW Controller 2 is a wireless controller which enables you to manage your LED strips and halogen lights.
Wirelessly control LEDs with an unlimited range of colour options
Monitors energy usage
Four analogue sensor inputs
Four dimmer channels
Acts as a repeater expanding your Z-Wave network
Content
The?Fibaro Dimmer Bypass 2?is designed to support?Fibaro Z-Wave In-Wall Dimmer 2 by enabling it to control and dim lights which draw a minimum of 5W (e.g LED lighting).
It can be used in the case of connecting LED bulbs or energy-saving compact fluorescent lamps. Fibaro Dimmer Bypass 2 prevents flickering of the LED lights and glowing of the turned off compact fluorescent lamps. In the case of a 2-wire connection, Fibaro Dimmer Bypass 2 allows to reduce minimum power of load required by the Fibaro Dimmer 2 for correct operation. Fibaro Dimmer Bypass 2 provides powering of the Fibaro Dimmer 2 in case of controlling the low loads of minimum power down to 5VA (for cos?>0.5)
Please note: Fibaro Dimmer Bypass 2 can only be used with Fibaro Dimmer 2.
This product must be installed by a qualified electrician.Before engaging an electrician, check that they provide a warranty and electrical compliance certificate.For a warranty claim, you have to provide an installation compliance certificate from your electrician.
Convert any existing wall switch into a smart switch without changing the wiring or running new cables with Shelly 1L. The first device in the world that is able to automate even the appliances wired with no neutral present. Thanks to its small size and wide range of voltage support, it's a real innovation!
NO NEUTRAL REQUIRED. Power and control your light, fan, or other appliances with only a live wire, no neutral required to be connected to the device.
OVERHEATING PROTECTION.?If the Shelly 1L reached high temperatures, it will switch OFF the output to protect itself and your home appliances.
MQTT ENABLED.?Easily integrate Shelly 1L to your existing home server using the MQTT or CoAP protocols
REST API.?Use the REST API to connect Shelly 1L to your existing home automation system.
HIGHLY COMPATIBLE. Compatible with Android, iOS, Amazon Alexa and Google Assistant. Control your appliance with your voice.
SUNRISE/SUNSET SCHEDULES. Shelly 1L can automatically follow the sunrise and sunset and control your lighting accordingly.
10 PackThis product is approved for use in Australia but must be installed by a licensed electrician.
Product Description
Control on tap.
Control one Z-Wave device. Control many. And all with a single tap.
There is simplicity in tapping touch glass. smartphones proved it. There is power too. Each of WallMote?s buttons can be programmed to control one Z-Wave device or many. Meaning that a single tap on its smooth surface can change a single light, a whole room, or your whole home. Tap good morning. Tap good night. Tap all the moments in between.
Tap. Control.
Control a light. Control a room. Control a home.Control a light. Control a room. Control a home.
Because WallMote communicates directly with your Z-Wave gateway, it can be used to control anything that your gateway can. Even things that are not Z-Wave. Smart lighting from Philips Hue? Check. Connected music from Sonos? Easy. If it is connected to your gateway, simply add it to a scene that WallMote can control and it is on top.
Wireless switch.
To be used anywhere in your home, WallMote and WallMote Quad need to be more than wireless. They need to be impressively wireless. Both switches offer a fine-tuned antenna capable of communicating over an open range of over 150 metres.
Secure switch.
Technology changes, now your wall switches change with it. WallMote and WallMote Quad are cutting-edge today and will be cutting-edge tomorrow. They are both capable of receiving wireless firmware updates via Z-Wave Plus so that they are always up to date.
Subtle switch.
Not just portable, but perfectly balanced. The minimalist design of both WallMote and WallMote Quad measures just 7.7cm wide and a slender 1.9cm deep
Simple recharging.
Battery powered but without the need to ever change a battery, WallMote and WallMote Quad are both powered by a rechargeable lithium battery designed for smartphones. It recharges just like a smartphone too via the provided micro USB cable.
Haptic feedback.
It is capable of controlling your whole home, so you may not even be present to see things change when you press WallMote?s touch glass. But you will feel the change. WallMote?s haptic engine confirms your every action via a click sensation.
Gen5 built in.
WallMote and WallMote Quad are part of Aeotec?s Gen5 range of Z-Wave devices. Built upon the latest version of Z-Wave- Z-Wave Plus ? cutting-edge performance and security is crafted into Z-Wave?s most advanced battery-powered wall switch.
? Power monitoring accuracy P=5-50W, +/-3W; P?50W, +/-3%;
? Digital temperature sensor range (sensor must be ordered separately) -50 ~ 125?C
??Support for the connection of digital temperature sensor (optional part)
? 2 binary inputs offer the option to connect additional devices such as sensors, switches/pushbuttons, etc, ?
Note!Do not connect the module to loads exceeding recommended values. Connect the module only in accordance with the manual and diagrams below. Use only qualified electricians!
The FIBARO Z-Wave RGBW Controller 2 is a one of a kind, advanced wireless 4-colour LED strip controller. Apart from the traditional RGB channels it also supports the white light channel which allows you to add pastel colours to your lighting decorations.
The FIBARO Z-Wave RGBW Controller 2 also has four analogue inputs supporting any type of Fibaro sensor (e.g. light sensors, wind sensors, pressure sensors and potentiometers operating between 0-10V). This smart feature allows you to use your lighting as a warning for certain events. You could, for example, set your RGB garden lights to turn red and flicker when one of your security sensors is triggered, alerting your neighbours to the intruder and allowing them to notify the proper authorities.
This device has four output channels which means that you can connect and independently control up to four light sources. The FIBARO Z-Wave RGBW Controller 2 also allows you to monitor the energy consumed by the LED strips. Each of the four channels can be monitored independently providing you with all the information you need to minimise your energy bills.
The FIBARO Z-Wave RGBW Controller 2 can control:
12 / 24V DC powered RGB strips
12 / 24V DC powered RGBW strips
12 / 24V DC powered LED strips, bulbs, etc
12 / 24V DC powered halogen lights
12 / 24V DC powered low output power fans
Note: Power supply is not included.
This product integrates with all Australian certified (921.42 MHz) Z-Wave controllers including:
Fibaro Home Center 3/Lite
Fibaro Yubii Home
Configuring Z-Wave Devices:
Z-Wave devices often have several configurable parameters which you can change using your Vera?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active for or the type of manual switch connected to a Z-Wave light controller.
Every available configurable parameter is listed in your device?s user manual. In most cases your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section.
Please check the maximum load before installing or operating.This device must be installed by a certified electrician.For all warranty claims, an electrical compliance certificate from your electrician must be provided.
Technical Specifications
RF Protocol
Z?Wave
RF Frequency
921.42Mhz ? AU/NZ ?approved RF for Z?wave
Z?Wave device type
Z-Wave dimmer
Power
12V and 24V
Operation Range
Up to 50m outdoors, up to 30m indoors (depending on terrain and building structure)
Application
Controlled automatically by pre-set Fibaro devices or manually using any Z-Wave controller
Simple to install.
WallMote is the wall switch for anywhere because it is simple to install. Mounting it requires just two steps.
Attach the mounting plate.
WallMote?s mounting plate affixes to any wall or surface using custom mounting tape. Peel. Stick. Done.
Attach WallMote.
WallMote is attractive. Literally. Place it in front of the mounting plate, and it will magnetically attach.
Control a light. Control a room. Control a home.Control a light. Control a room. Control a home.
Because WallMote communicates directly with your Z-Wave gateway, it can be used to control anything that your gateway can. Even things that are not Z-Wave. Smart lighting from Philips Hue? Check. Connected music from Sonos? Easy. If it is connected to your gateway, simply add it to a scene that WallMote can control and it is on top.
Wireless switch.
To be used anywhere in your home, WallMote and WallMote Quad need to be more than wireless. They need to be impressively wireless. Both switches offer a fine-tuned antenna capable of communicating over an open range of over 150 metres.
Secure switch.
Technology changes, now your wall switches change with it. WallMote and WallMote Quad are cutting-edge today and will be cutting-edge tomorrow. They are both capable of receiving wireless firmware updates via Z-Wave Plus so that they are always up to date.
Subtle switch.
Not just portable, but perfectly balanced. The minimalist design of both WallMote and WallMote Quad measures just 7.7cm wide and a slender 1.9cm deep
Simple recharging.
Battery powered but without the need to ever change a battery, WallMote and WallMote Quad are both powered by a rechargeable lithium battery designed for smartphones. It recharges just like a smartphone too via the provided micro USB cable.
Haptic feedback.
It is capable of controlling your whole home, so you may not even be present to see things change when you press WallMote?s touch glass. But you will feel the change. WallMote?s haptic engine confirms your every action via a click sensation.
Gen5 built in.
WallMote and WallMote Quad are part of Aeotec?s Gen5 range of Z-Wave devices. Built upon the latest version of Z-Wave- Z-Wave Plus ? cutting-edge performance and security is crafted into Z-Wave?s most advanced battery-powered wall switch.
