The absolute best selling?QUBINO Z-Wave Dimmer 0-10V?(by GOAP) is unique. This Z-Wave product was developed to cater for the needs of Smart Home users looking for a Z-Wave solution that controls devices such as lights, fans and similar products with a 0-10V signal.?The QUBINO Flush Dimmer 0-10V is ideal for remotely dimming LED lights with low voltage ballast.
QUBINO?modules are ?install-and-forget? products. QUBINO are made to last, so we only select and use top-quality electronic components. These modules are also the most tested Z-Wave microcontrollers on the market. The Slovenian Institute of Quality and Metrology (SIQ), an independent testing body, tests safety parameters including temperature rise, construction, insulation resistance, power consumption and overload in accordance with the EN 60669-2-1 standard.
QUBINO Ltd. is a European company with 26-years experience in the automation field. With their expertise and passion for innovation in automation, they have developed a unique, ready to sell, certified and reliable portfolio of 14 Z-Wave wireless Smart Home products under different brands and OEMs around the world.
Unlimited controlling capability through a gateway
Z-Wave Plus compliant
23 additional parameters for expert users
Product Support
Please note:?If you are installing the entire Z-Wave? system for the first time, please refer to?the installation guide of your Z-Wave gateway before installing this device.
The GOAP Flush Dimmer uses a unique MOSFET ‘trailing edge’ dimmer to enable it to work with a huge range of bulb types:
Halogen and Incandescent (230V)
Dimmable LEDs (230V)
Dimmable CFL and Fluorescent (230V)
Low Voltage Halogen (24V)
Low Voltage LED (24V)
The QUBINO Z-Wave Dimmer can be used in the 230V mains lighting system where it uses a ‘Trailing Edge’ style dimmer to control the lights. It can also be used in a 24V low-voltage system where it uses PWM style control of the bulbs.
Please note: These devices require a 3-wire system (including neutral), please check your installation before purchasing. If you have a 2-wire system (without neutral) we recommend you use a FIBARO Z-Wave Dimmer 2.
The absolute best selling?QUBINO Z-Wave Dimmer 0-10V?(by GOAP) is unique. This Z-Wave product was developed to cater for the needs of Smart Home users looking for a Z-Wave solution that controls devices such as lights, fans and similar products with a 0-10V signal.?The QUBINO Flush Dimmer 0-10V is ideal for remotely dimming LED lights with low voltage ballast.
QUBINO?modules are ?install-and-forget? products. QUBINO are made to last, so we only select and use top-quality electronic components. These modules are also the most tested Z-Wave microcontrollers on the market. The Slovenian Institute of Quality and Metrology (SIQ), an independent testing body, tests safety parameters including temperature rise, construction, insulation resistance, power consumption and overload in accordance with the EN 60669-2-1 standard.
QUBINO Ltd. is a European company with 26-years experience in the automation field. With their expertise and passion for innovation in automation, they have developed a unique, ready to sell, certified and reliable portfolio of 14 Z-Wave wireless Smart Home products under different brands and OEMs around the world.
The?QUBINO Single Switch (by GOAP) is a Z-Wave module for switching on/off the electrical device (e.g. light, fan, etc ...). The module can be controlled either through the Z-wave network or through the wall switch manually.
This module is designed to be mounted behind a traditional wall switch. The module measures the power consumption of load and supports the connection of the digital temperature sensor. It is designed to act as a repeater in order to improve the range and stability of the Z-Wave network.
Supported switches
The module supports mono-stable switches (push button) and bi-stable switches. The module is factory set to operate with bi-stable switches.
On any wall.
WallMote is the wall switch that you can install anywhere. Wirelessly.
Whatever the room, whatever the wall, WallMote is perfect. The wireless Z-Wave wall switch that you can place anywhere, on any wall, with as little as double-sided tape. Unpack it. Stick it. Charge it. Control is just a tap away.
Simple to install.
WallMote is the wall switch for anywhere because it is simple to install. Mounting it requires just two steps.
Attach the mounting plate.
WallMote?s mounting plate affixes to any wall or surface using custom mounting tape. Peel. Stick. Done.
Attach WallMote.
WallMote is attractive. Literally. Place it in front of the mounting plate, and it will magnetically attach.
The Fibaro Z-Wave In-Wall Dimmer 2 (FGD-212) is the newest version of a popular wireless controller designed to operate behind a wall switch.
Control the level of illumination of your light remotely or using a manual button (in two and three way configurations)
Implemented algorithm of smart light source detection
Acts as a repeater expanding your Z-Wave network
Wide range of compatibility with existing light fittings and does NOT require expensive re-wiring
Active power and energy metering functionality
Works with various types of manual buttons
Active element: semiconductor electronic switch
The FIBARO Z-Wave RGBW Controller 2 is a wireless controller which enables you to manage your LED strips and halogen lights.
Wirelessly control LEDs with an unlimited range of colour options
Monitors energy usage
Four analogue sensor inputs
Four dimmer channels
Acts as a repeater expanding your Z-Wave network
Control any switch. From anywhere.?Wirelessly.
Power sockets and light switches: amazing inventions. They literally changed the world. But if you?re not standing right next to them or can?t reach them, they?re limited.
No more. The future is smarter. So is your home. The?AEOTEC Dual Nano Switch InWall?offers complete wireless control of your switches and sockets.
The?AEOTEC Nano Switch?offers total control, easily. Impossibly small, each?AEOTEC Dual Nano Switch?installs invisibly behind any of your home?s existing switches or power sockets. Simply unscrew the faceplate, install the?AEOTEC Nano Switch?behind it, and you now have complete wireless control. Your old switches are instantly modern and instantly connected.
Content
All?QUBINO?modules are manufactured in Italy.
The?QUBINO?Z-Wave Dimmer 0-10V occupies a smaller volume than comparable modules of any other brand and will fit easily in any flush mounting box
Standard 0-10V output
Multi-function input in connection with: push button / switch / potentiometer / input 0-10V (any sensor with 0-10V output)
Perfect for dimming lights with ballast 0-10V
Controlling fan speed (for motors or frequency inverters with 0-10V speed control input)
Unlimited controlling capability through a gateway
Z-Wave Plus compliant
23 additional parameters for expert users
Product Support
Please note:?If you are installing the entire Z-Wave? system for the first time, please refer to?the installation guide of your Z-Wave gateway before installing this device.
The GOAP Flush Dimmer uses a unique MOSFET 'trailing edge' dimmer to enable it to work with a huge range of bulb types:
Halogen and Incandescent (230V)
Dimmable LEDs (230V)
Dimmable CFL and Fluorescent (230V)
Low Voltage Halogen (24V)
Low Voltage LED (24V)
The QUBINO Z-Wave Dimmer can be used in the 230V mains lighting system where it uses a 'Trailing Edge' style dimmer to control the lights. It can also be used in a 24V low-voltage system where it uses PWM style control of the bulbs.
Please note: These devices require a 3-wire system (including neutral), please check your installation before purchasing. If you have a 2-wire system (without neutral) we recommend you use a FIBARO Z-Wave Dimmer 2.
Technical Specification
RF Protocol
Z-Wave Plus?, SDK version: 6.51.03
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Application
Indoor use only
Power
12-24 VDC
Operation Range
Up to 50m indoors with no obstacles
Enclosure
Plastic
Compliance
EN 60669-2-1
Operating Temp.
?-10C ~ +50C
Max. control voltage ratings
-20/+20VDC
Control signal range
0-11VDC
Max. sinking current
2 mA
Max. sourcing current
10 mA
Dimensions
41.8 mm x 36.8 mm x 15.4 mm
? Compatible with any Z-Wave Controller.
? Dimensions (W x H x D) 41,8 x 36,8 x 15,4mm
? Power monitoring accuracy P=5-50W, +/-3W; P?50W, +/-3%;
? Digital temperature sensor range (sensor must be ordered separately) -50 ~ 125?C
??Support for the connection of digital temperature sensor (optional part)
? 2 binary inputs offer the option to connect additional devices such as sensors, switches/pushbuttons, etc, ?
Note!Do not connect the module to loads exceeding recommended values. Connect the module only in accordance with the manual and diagrams below. Use only qualified electricians!
Control on tap.
Control one Z-Wave device. Control many. And all with a single tap.
There is simplicity in tapping touch glass. smartphones proved it. There is power too. Each of WallMote?s buttons can be programmed to control one Z-Wave device or many. Meaning that a single tap on its smooth surface can change a single light, a whole room, or your whole home. Tap good morning. Tap good night. Tap all the moments in between.
Tap. Control.
Control a light. Control a room. Control a home.Control a light. Control a room. Control a home.
Because WallMote communicates directly with your Z-Wave gateway, it can be used to control anything that your gateway can. Even things that are not Z-Wave. Smart lighting from Philips Hue? Check. Connected music from Sonos? Easy. If it is connected to your gateway, simply add it to a scene that WallMote can control and it is on top.
Wireless switch.
To be used anywhere in your home, WallMote and WallMote Quad need to be more than wireless. They need to be impressively wireless. Both switches offer a fine-tuned antenna capable of communicating over an open range of over 150 metres.
Secure switch.
Technology changes, now your wall switches change with it. WallMote and WallMote Quad are cutting-edge today and will be cutting-edge tomorrow. They are both capable of receiving wireless firmware updates via Z-Wave Plus so that they are always up to date.
Subtle switch.
Not just portable, but perfectly balanced. The minimalist design of both WallMote and WallMote Quad measures just 7.7cm wide and a slender 1.9cm deep
Simple recharging.
Battery powered but without the need to ever change a battery, WallMote and WallMote Quad are both powered by a rechargeable lithium battery designed for smartphones. It recharges just like a smartphone too via the provided micro USB cable.
Haptic feedback.
It is capable of controlling your whole home, so you may not even be present to see things change when you press WallMote?s touch glass. But you will feel the change. WallMote?s haptic engine confirms your every action via a click sensation.
Gen5 built in.
WallMote and WallMote Quad are part of Aeotec?s Gen5 range of Z-Wave devices. Built upon the latest version of Z-Wave- Z-Wave Plus ? cutting-edge performance and security is crafted into Z-Wave?s most advanced battery-powered wall switch.
The Fibaro Z-Wave In-Wall Dimmer 2 is designed to operate with or without a neutral wire. It may be used as a switch in systems without a neutral wire.
In the case of a 2-wire connection (no neutral), the Fibaro Z-Wave In-Wall Dimmer 2 may require a minimum load of 50W depending on the specifics of the connected load.
When used with a Fibaro Dimmer Bypass 2 it may operate with any compatible (see below) load from 5W. Before committing to buy Fibaro Dimmer Bypass 2 please check if your load can be properly controlled by Fibaro Dimmer 2 without a bypass device.
Do not connect this device to a power supply without a load. Only lighting devices may be connected to this device.
As a dimmer it operates with the following loads:
230V operated conventional incandescent (from 50W to 250W)
230V operated halogen (from 50W to 200W)
12 V operated ELV halogen lamps and dimmable LED lamps (with electronic transformers: Trailing and Leading-edge type) (from 50W to 200W)
Dimmable CFL tube lamps with electronic ballast only (from 50W to 200W)
As a switch it operates with the following loads:
Compact fluorescent lamps with electronic ballast
LED bulbs (power factor >0.7)
Fluorescent tube lamps with electronic ballast
Please note: For loads other than resistive do not exceed a 1.5A current.
This product integrates with all Australian certified (921.42 MHz) Z-Wave and Z-Wave Plus controllers including:
Vera Plus/ Edge
Fibaro Home Center 2 / Lite
Please note: Do not mix the load type (e.g. LED and CFL or different types of transformers) as it will impede the proper operation of the dimmer. Doing so will void the dimmer's warranty.
This product must be installed by a qualified electrician.Before engaging an electrician, check that they provide a warranty and electrical compliance certificate.For a warranty claim, you have to provide an installation compliance certificate from your electrician.PLEASE NOTE FOR THE INSTALLATIONS IN THE AREAS WHERE ELECTRICITY SUPPLIERS USE OFF-PEAK RIPPLE CONTROL SIGNALS:
Electricity suppliers in particular areas of Australia such as NSW, QLD and some other places are injecting an off-peak ripple control signal using Zellweger equipment or similar onto their distribution networks in order to remotely control devices such as off-peak hot water systems and street lighting, although other areas within Australia also use this technology. Not all properties are affected by ripple control, so just because you might live in one of these areas, does not mean that you will have these problems.
Ripple injection control systems work by superimposing coded control signals, commonly 750Hz or 1050Hz on the 50 Hz mains supply.
Some electrical appliances such as fans, dimmers, toasters and LED lighting can be sensitive to this ripple control signal. The results could be audible buzzing noises from fans or flickering lights whenever the ripple control signals are present.
Electricity suppliers are advising users to install appropriate ripple signal filters in such areas.
The ripple signal filter is a tuned passive inline filter that completely eliminates the superimposed ripple injection control signal from the normal mains supply to produce a noise free filtered mains supply which can then be connected to the electrical appliances or light control systems. The ripple signal filter is specifically tuned to eliminate the ripple control signal frequency of 750Hz or 1050Hz.
However, we can?t guarantee the ripple signal filter always will help you if you experiencing such issues. Please contact your local energy provider to get more information and proposed solutions for your electrical installation.
If you are getting similar problems with your dimmers and fans and it?s not Ripple Control Signal and you are hearing the tones at random times of the day, your electrical supply may be affected by harmonics; a power fluctuation that is not part of the normal electricity supply or ripple control signal output.
Harmonics are caused by interference created by other equipment on the network, such as inverter type air conditioners and switch mode power supplies for computers.
The offending appliances may be in your home or other premises on the local power grid. If you are being affected by network harmonics, it may be of benefit to transfer the electricity supply to your premises to a different phase in the street. This is something you will need to discuss with your electrical company.
We are strongly recommending for the areas we have mentioned above to run tests with only a few dimmers before committing for high volumes. If results are not fully OK you may use relays only instead of dimmers.
Please note that our warranty for the faulty devices is not covering above mentioned conditions with your local electric grids.
Please see affected with Ripple Signalling areas here:
QUEENSLAND
Only Southern Queensland (Energex) has Ripple Signalling.
The Frequency is 1050Hz.
The rest of Queensland (Ergon) does not have Ripple Signalling.
Up to 30m indoors (depending on building materials)
Application
Indoor use only
Operation temperature
0 ~ 35 ?C
Dimensions (L x W x H)
42.5mm x 38.25mm x 20.3mm
Weight
30g
Operational Current
0.25 - 1.1A
Compliance
RCM E3606
Dimming type compatibility
Leading and Trailing Edge
The FIBARO Z-Wave RGBW Controller 2 is a one of a kind, advanced wireless 4-colour LED strip controller. Apart from the traditional RGB channels it also supports the white light channel which allows you to add pastel colours to your lighting decorations.
The FIBARO Z-Wave RGBW Controller 2 also has four analogue inputs supporting any type of Fibaro sensor (e.g. light sensors, wind sensors, pressure sensors and potentiometers operating between 0-10V). This smart feature allows you to use your lighting as a warning for certain events. You could, for example, set your RGB garden lights to turn red and flicker when one of your security sensors is triggered, alerting your neighbours to the intruder and allowing them to notify the proper authorities.
This device has four output channels which means that you can connect and independently control up to four light sources. The FIBARO Z-Wave RGBW Controller 2 also allows you to monitor the energy consumed by the LED strips. Each of the four channels can be monitored independently providing you with all the information you need to minimise your energy bills.
The FIBARO Z-Wave RGBW Controller 2 can control:
12 / 24V DC powered RGB strips
12 / 24V DC powered RGBW strips
12 / 24V DC powered LED strips, bulbs, etc
12 / 24V DC powered halogen lights
12 / 24V DC powered low output power fans
Note: Power supply is not included.
This product integrates with all Australian certified (921.42 MHz) Z-Wave controllers including:
Fibaro Home Center 3/Lite
Fibaro Yubii Home
Configuring Z-Wave Devices:
Z-Wave devices often have several configurable parameters which you can change using your Vera?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active for or the type of manual switch connected to a Z-Wave light controller.
Every available configurable parameter is listed in your device?s user manual. In most cases your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section.
Please check the maximum load before installing or operating.This device must be installed by a certified electrician.For all warranty claims, an electrical compliance certificate from your electrician must be provided.
Technical Specifications
RF Protocol
Z?Wave
RF Frequency
921.42Mhz ? AU/NZ ?approved RF for Z?wave
Z?Wave device type
Z-Wave dimmer
Power
12V and 24V
Operation Range
Up to 50m outdoors, up to 30m indoors (depending on terrain and building structure)
Application
Controlled automatically by pre-set Fibaro devices or manually using any Z-Wave controller
Once installed behind a switch or socket, the?AEOTEC Dual Nano Switch offers unparalleled wireless control via Z-Wave protocol. It lets you control, automate, and monitor your lights and power sockets. From anywhere. Anytime. And it does it all through enhancement ? with the AEOTEC Nano Switch, your sockets and switches don?t have to be replaced and they?ll continue to offer the same manual control that you?re used to.
Simple to install.
WallMote is the wall switch for anywhere because it is simple to install. Mounting it requires just two steps.
Attach the mounting plate.
WallMote?s mounting plate affixes to any wall or surface using custom mounting tape. Peel. Stick. Done.
Attach WallMote.
WallMote is attractive. Literally. Place it in front of the mounting plate, and it will magnetically attach.
The?AEOTEC Nano Switch?offers total control, easily. Impossibly small, each?AEOTEC Dual Nano Switch?installs invisibly behind any of your home?s existing switches or power sockets. Simply unscrew the faceplate, install the?AEOTEC Nano Switch?behind it, and you now have complete wireless control. Your old switches are instantly modern and instantly connected.
Control a light. Control a room. Control a home.Control a light. Control a room. Control a home.
Because WallMote communicates directly with your Z-Wave gateway, it can be used to control anything that your gateway can. Even things that are not Z-Wave. Smart lighting from Philips Hue? Check. Connected music from Sonos? Easy. If it is connected to your gateway, simply add it to a scene that WallMote can control and it is on top.
Wireless switch.
To be used anywhere in your home, WallMote and WallMote Quad need to be more than wireless. They need to be impressively wireless. Both switches offer a fine-tuned antenna capable of communicating over an open range of over 150 metres.
Secure switch.
Technology changes, now your wall switches change with it. WallMote and WallMote Quad are cutting-edge today and will be cutting-edge tomorrow. They are both capable of receiving wireless firmware updates via Z-Wave Plus so that they are always up to date.
Subtle switch.
Not just portable, but perfectly balanced. The minimalist design of both WallMote and WallMote Quad measures just 7.7cm wide and a slender 1.9cm deep
Simple recharging.
Battery powered but without the need to ever change a battery, WallMote and WallMote Quad are both powered by a rechargeable lithium battery designed for smartphones. It recharges just like a smartphone too via the provided micro USB cable.
Haptic feedback.
It is capable of controlling your whole home, so you may not even be present to see things change when you press WallMote?s touch glass. But you will feel the change. WallMote?s haptic engine confirms your every action via a click sensation.
Gen5 built in.
WallMote and WallMote Quad are part of Aeotec?s Gen5 range of Z-Wave devices. Built upon the latest version of Z-Wave- Z-Wave Plus ? cutting-edge performance and security is crafted into Z-Wave?s most advanced battery-powered wall switch.
