FIBARO Z-Wave Double Switch 2

$84.99

Availability: In Stock

The new Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave wireless module which can control two circuits each with a maximum load of 6.5A per channel and 10A total load per circuit.

  • Control the ON-OFF function of two two independent circuits or appliances remotely or using a wall switch
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling
  • Latest generation Z-Wave 500 series chip
  • Z-Wave Plus certification
  • Very accurate energy measurement +/- 1 % for power above 5W
  • Supports secure mode (Z-Wave Network Security) encrypted with AES-128
  • No dry contacts – this is important. It means that the new FGS-223 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.

Discount per quantity

Quantity 4 - 7 8+
Price $80.74 $76.49
% Discount 5% 10%

Buy More for Bigger Savings!

20 in stock

SKU: DHS-LIT-SWW-FIB-022 Categories: , Tags: , ,

Description

Product Details

The Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.

The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.

This Fibaro Fibaro Z-Wave Double Switch 2 requires 3-wire (including neutral) installation and works with an AC (230V) power supply.

The Fibaro Z-Wave Double Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits.

This product integrates with Australian certified (921.42 MHz) Z-Wave Controllers – Fibaro Home Center 2/Lite

Note: It doesn’t integrate with Vera gateways at this stage.

Configuring Z-Wave Devices:

Z-Wave devices often have several configurable parameters which you can change using Fibaro?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller.

Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device.

Please check the maximum load before installing or operating.
This installation must be done by a certified electrician in Australia and New Zealand.
Before engaging an electrician, check that they provide an electrical compliance certificate.
For a warranty claim, you have to provide an installation compliance certificate from your electrician.

Documentation

Fibaro Z-Wave Double Switch 2 Manual

Technical Specification

RF Protocol
Z-Wave
RF Frequency
921.42Mhz – AU/NZ ?approved RF for Z-wave
Z?Wave device type
Z-Wave Switch, Routing Slave
Power
230V?? 10% 50/60 Hz
Operation Range
Up to 20 m indoors with no obstacles
Application
Indoor use only, up to?1.5kW resistive load per circuit
Operation temperature
0 ~ 55 ?C
Storage temperature
-10 ~ 80 ?C
Weight
50g
Housing
ABS
Compliance
EN 55015, EN 60669-2-1
Regulatory Compliance Mark
N5496
Dimensions
(LxWxH) 42mm x 37mm x 17mm

Quick Comparison

SettingsFIBARO Z-Wave Double Switch 2 removeAEOTEC Nano Sgl Switch InWall removeQUBINO Z-Wave Dimmer removeSHELLY 2.5 Double Relay WiFi Switch removeQUBINO Z-Wave 1 Relay removeFIBARO Z-Wave RGBW Controller 2 remove
Image
SKUDHS-LIT-SWW-FIB-022DHS-LIT-SWW-AEO-01DHS-LIT-DMW-QUBSH-SHELLY25DHS-LIT-SWW-QUB-01DHS-LIT-RGBW-FIB
Rating
Price$84.99$89.99$79.99$39.99$88.99$84.99
Stock

20 in stock

Out of stock

20 in stock

50 in stock

Out of stock

2 in stock

Availability20 in stockOut of stock20 in stock50 in stockOut of stock2 in stock
Add to cart

Add to basket

Read more

Add to basket

Add to basket

Read more

Add to basket

DescriptionThe new Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave wireless module which can control two circuits each with a maximum load of 6.5A per channel and 10A total load per circuit.
  • Control the ON-OFF function of two two independent circuits or appliances remotely or using a wall switch
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling
  • Latest generation Z-Wave 500 series chip
  • Z-Wave Plus certification
  • Very accurate energy measurement +/- 1 % for power above 5W
  • Supports secure mode (Z-Wave Network Security) encrypted with AES-128
  • No dry contacts - this is important. It means that the new FGS-223 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
Control any switch. From anywhere.?Wirelessly. Power sockets and light switches: amazing inventions. They literally changed the world. But if you?re not standing right next to them or can?t reach them, they?re limited.?No more. The future is smarter. So is your home. The?AEOTEC Nano Switch InWall?offers completely wireless control of your switches and sockets. ZW116a The?AEOTEC Nano Switch?offers total control, easily. Impossibly small, each?AEOTEC Nano Switch?installs invisibly behind any of your home?s existing switches or power sockets. Simply unscrew the faceplate, install the?AEOTEC Nano Switch?behind it, and you now have complete wireless control. Your old switches are instantly modern and instantly connected.The?QUBINO Dimmer?(by GOAP) is the first MOSFET- switching light Z-Wave dimmer module that also supports control of low-voltage halogen lamps with electronic transformers, dimmable compact fluorescent lights and dimmable LED bulbs. It also measures the power consumption of electrical devices and supports the connection of a digital temperature sensor. QUBINO?modules are ?install-and-forget? products. Our products are made to last, so we only select and use top-quality electronic components. These modules are also the most tested Z-Wave microcontrollers on the market. The Slovenian Institute of Quality and Metrology (SIQ), an independent testing body, tests safety parameters including temperature rise, construction, insulation resistance, power consumption and overload in accordance with the EN 60669-2-1 standard.

SHELLY 2.5 RELAY SWITCH, ROLLER SHUTTER 2X10A

  • Wi-Fi Connected
  • For two electrical circuits (up to 2.3 kW each) with energy consumption monitoring
  • Mobile App Control
  • REST API to connect Shelly with your existing home automation system
  • Wide range of AC and DC power supply: 110-230V ? 10, 50 / 60Hz AC or 24-60V DC
Control a wide range of home appliances and office equipment (lights, power lines, garage doors, curtains, security systems, heating radiators, air conditioners, etc.) from anywhere with the smallest WiFi-operated double relay switch with roller shutter functionality in the world ? Shelly 2.5

Shelly 2.5 WiFi Double Relay Switch Roller Shutter, Neutral wire is required.

Has an embedded web server; Has been designed for installation in a limited space, such as wall mounts, electrical control panels, etc; Can be used for two electrical circuits (up to 2.3 kW each) with energy consumption monitoring for each channel, overload, and temperature protection. Can operate as a bi-directional motor control module (for drapes, blinds, garage doors, etc.). Can function as a standalone device, as an accessory to a home automation controller, or it may be used as another automation system?s component.   TECHNICAL SPECIFICATIONS
  • Intelligent On/Off
  • Power Supply: 110-230V ?10, 50/60Hz AC and 24-60V DC
  • Compatible with all major international voltage standards.
  • 2 Channels ? Maximum load current per output: 10A / 230V 50/60Hz.
  • Complies with the following EU standards: RE Directive 2014/53/EU, LVD 2006/95/WE, EMC 2004/108/WE, RoHS2 2011/65/UE
  • Operational temperature: -40 to +40 ?C
  • Dimensions (LxWxH): 39 x 36 x 17 mm
  • Minimum mounting opening: ? ? 50mm
  • Radio signal power: 1mW
  • Wireless/WiFi Protocol: 802.11 b/g/n
  • Radio frequency: 2400 ? 2500 MHz
  • Range: up to 50 m outdoors and up to 30 m indoors (depending on the building materials)
  • Electrical power consumption < 1 W
  • Microprocessor control
  • Independent dual power metering for each channel
  • Overload and temperature protection
  • Can connect to any Wi-Fi network or can operate as an Access Point
  • Controlled via WiFi and a mobile phone, computer, automation system or any other device supporting HTTP and/or UDP protocol
  • Controlled elements: 2 electrical circuits
  • Executive elements: 2 relays
  • Can be operated along with momentary keys or push-button switches
  • Has an integrated precise power meter.
This product is approved for use in Australia but must be installed by a licensed electrician.
The?QUBINO Single Switch (by GOAP) is a Z-Wave module for switching on/off the electrical device (e.g. light, fan, etc ...). The module can be controlled either through the Z-wave network or through the wall switch manually. This module is designed to be mounted behind a traditional wall switch. The module measures the power consumption of load and supports the connection of the digital temperature sensor. It is designed to act as a repeater in order to improve the range and stability of the Z-Wave network. Supported switches The module supports mono-stable switches (push button) and bi-stable switches. The module is factory set to operate with bi-stable switches.The FIBARO Z-Wave RGBW Controller 2 is a wireless controller which enables you to manage your LED strips and halogen lights.
  • Wirelessly control LEDs with an unlimited range of colour options
  • Monitors energy usage
  • Four analogue sensor inputs
  • Four dimmer channels
  • Acts as a repeater expanding your Z-Wave network
Content

Product Details

The Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene. The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician. This Fibaro Fibaro Z-Wave Double Switch 2 requires 3-wire (including neutral) installation and works with an AC (230V) power supply. The Fibaro Z-Wave Double Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits. This product integrates with Australian certified (921.42 MHz) Z-Wave Controllers - Fibaro Home Center 2/Lite Note: It doesn't integrate with Vera gateways at this stage.

Configuring Z-Wave Devices:

Z-Wave devices often have several configurable parameters which you can change using Fibaro?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller. Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. Please check the maximum load before installing or operating. This installation must be done by a certified electrician in Australia and New Zealand. Before engaging an electrician, check that they provide an electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician.

Documentation

Fibaro Z-Wave Double Switch 2 Manual

Technical Specification

RF Protocol
Z-Wave
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Z?Wave device type
Z-Wave Switch, Routing Slave
Power
230V?? 10% 50/60 Hz
Operation Range
Up to 20 m indoors with no obstacles
Application
Indoor use only, up to?1.5kW resistive load per circuit
Operation temperature
0 ~ 55 ?C
Storage temperature
-10 ~ 80 ?C
Weight
50g
Housing
ABS
Compliance
EN 55015, EN 60669-2-1
Regulatory Compliance Mark
N5496
Dimensions
(LxWxH) 42mm x 37mm x 17mm

Product Description

Once installed behind a switch or socket, the?AEOTEC Nano Switch?offers unparalleled wireless control via Z-Wave protocol. It lets you control, automate, and monitor your lights light and power sockets. From anywhere. Anytime. And it does it all through enhancement ? with the?AEOTEC Nano Switch, your sockets and switches don?t have to be replaced and they?ll continue to offer the same manual control that you?re used to. ZW098 B22dd

Product Support

Since the AEOTEC Nano Switch also supports the 24VDC power input,? you can also use it to control loads powered by 24VDC?(see user manual) Works with VeraAeotec LED Bulb with Vera Manuals: ?? Aeotec Nano Switch product manual

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Z-Wave device type
Switch
Power
240V AC
Operation Range
Up to 40m without obstacles
Application
Indoor use only
Operation temperature
0 ~ 55 ?C
Storage temperature
-10 ~ 80 ?C
Colour
white
Weight
50g
Housing
ABS
Size
42mm x 40mm x 25mm
Compliance
Z-Wave Plus certified
Warranty 12 Months
All QUBINO modules are manufactured in Europe by GOAP.
  • The QUBINO Z-Wave Dimmer module occupies a smaller volume than comparable modules of any other brand and will fit easily in any flush mounting box.
  • The QUBINO Z-Wave?Dimmer can measure the power consumption of the connected electrical device and itself has an extremely low power consumption of just 0.7 W.
  • The QUBINO Z-Wave?Dimmer can operate across a wide temperature range, from a chilly -10?C to a scorching 40?C (14??104?F). It supports the connection of a digital temperature sensor, which is also useful for creating complex scenarios. Every module also acts as a repeater in order to improve the range and stability of the Z-Wave network.
  • Unlimited controlling capability through a gateway
  • Setting mono-stable (push button) or bi-stable switch type
  • Z-Wave Plus compliant
  • 23 additional parameters for expert users

Product Support

Please note:?If you are installing the entire Z-Wave? system for the first time, please refer to?the installation guide of your Z-Wave gateway before installing this device. The QUBINO Flush Dimmer uses a unique MOSFET 'trailing edge' dimmer to enable it to work with a huge range of bulb types: Halogen and Incandescent (230V) Dimmable LEDs (230V) Dimmable CFL and Fluorescent (230V) Low Voltage Halogen (24V) Low Voltage LED (24V) The QUBINO Dimmer can be used in the 230V mains lighting system where it uses a 'Trailing Edge' style dimmer to control the lights. It can also be used in a 24V low-voltage system where it uses PWM style control of the bulbs. Please note: These devices require a 3-wire system (including neutral), please check your installation before purchasing. If you have a 2-wire system (without neutral) we recommend you use a FIBARO Z-Wave Dimmer 2 PLEASE NOTE FOR THE INSTALLATIONS IN THE AREAS WHERE ELECTRICITY SUPPLIERS USE OFF-PEAK RIPPLE CONTROL SIGNALS: Electricity suppliers in particular areas of Australia such as NSW, QLD and some other places are injecting an off-peak ripple control signal using Zellweger equipment?or similar onto their distribution networks in order to remotely control devices such as off-peak hot water systems and street lighting, although other areas within Australia also use this technology. Not all properties are affected by ripple control, so just because you might live in one of these areas, does not mean that you will have these problems. Ripple injection control systems work by superimposing coded control signals, commonly 750Hz or 1050Hz on the 50 Hz mains supply. Some electrical appliances such as fans, dimmers, toasters and LED lighting can be sensitive to this ripple control signal. The results could be audible buzzing noises from fans or flickering lights whenever the ripple control signals are present. Electricity suppliers are advising users to install appropriate?ripple signal filters in such areas. The ripple signal filter is a tuned passive inline filter that completely eliminates the superimposed ripple injection control signal from the normal mains supply to produce a noise-free filtered mains supply which can then be connected to the electrical appliances or light control systems. The ripple signal filter is specifically tuned to eliminate the ripple control signal frequency of 750Hz or 1050Hz. However, we can?t guarantee the ripple signal filter always will help you if you experiencing such issues. Please contact your local energy provider to get more information and proposed solutions for your electrical installation. If you are getting similar problems with your dimmers and fans and it?s not Ripple Control Signal and you are hearing the tones at random times of the day, your electrical supply may be affected by harmonics; a power fluctuation that is not part of the normal electricity supply or ripple control signal output. Harmonics are caused by an interference created by other equipment on the network, such as inverter type air conditioners and switch-mode power supplies for computers. The offending appliances may be in your home or other premises on the local power grid. If you are being affected by network harmonics, it may be of benefit to transfer the electricity supply to your premises to a different phase in the street. This is something you will need to discuss with your electrical company. We are strongly recommending for the areas we have mentioned above to run tests with only a few dimmers before committing for high volumes. If results are not fully OK you may use relays only instead of dimmers. Please note that our warranty for the faulty devices is not covering the above-mentioned conditions with your local electric grids. Please see affected with Ripple Signalling areas here: QUEENSLAND
  • Only Southern Queensland (Energex) has Ripple Signalling.
  • The Frequency is 1050Hz.
  • The rest of Queensland (Ergon) does not have Ripple Signalling.
QLD NSW
  • Energy Australia Full Supply Area
  • Energy Australia Sydney &Hunter Supply Area
NSW
? Compatible with any Z-Wave Controller.
? Dimensions (W x H x D) 41,8 x 36,8 x 15,4mm
? Power monitoring accuracy P=5-50W, +/-3W; P?50W, +/-3%;
? Digital temperature sensor range (sensor must be ordered separately) -50 ~ 125?C
??Support for the connection of digital temperature sensor (optional part)
? 2 binary inputs offer the option to connect additional devices such as sensors, switches/pushbuttons, etc, ?
Note! Do not connect the module to loads exceeding recommended values. Connect the module only in accordance with the manual and diagrams below. Use only qualified electricians!

Technical Specifications

Product Name?
?Flush 1 relay
Powered by
24V DC or 240V AC
Operation Range
30m
Max Load
2300W (230VAC)
Radio frequency
921.42 MHz (AU/NZ Z-Wave)
Power Consumption
0,4W
Operation temperature
-10 -+40 C*
Measured temperature range 0,5o?C (within 0o?C - 40o?C range) (optional sensor)
Temperature measuring accuracy
0,5 C
Housing
ABS
Dimensions (W x H x D)
41,8 x 36,8 x 15,4mm
The FIBARO Z-Wave RGBW Controller 2 is a one of a kind, advanced wireless 4-colour LED strip controller. Apart from the traditional RGB channels it also supports the white light channel which allows you to add pastel colours to your lighting decorations. The FIBARO Z-Wave RGBW Controller 2 also has four analogue inputs supporting any type of Fibaro sensor (e.g. light sensors, wind sensors, pressure sensors and potentiometers operating between 0-10V). This smart feature allows you to use your lighting as a warning for certain events. You could, for example, set your RGB garden lights to turn red and flicker when one of your security sensors is triggered, alerting your neighbours to the intruder and allowing them to notify the proper authorities. This device has four output channels which means that you can connect and independently control up to four light sources. The FIBARO Z-Wave RGBW Controller 2 also allows you to monitor the energy consumed by the LED strips. Each of the four channels can be monitored independently providing you with all the information you need to minimise your energy bills. The FIBARO Z-Wave RGBW Controller 2 can control:
  • 12 / 24V DC powered RGB strips
  • 12 / 24V DC powered RGBW strips
  • 12 / 24V DC powered LED strips, bulbs, etc
  • 12 / 24V DC powered halogen lights
  • 12 / 24V DC powered low output power fans
Note: Power supply is not included. This product integrates with all Australian certified (921.42 MHz) Z-Wave controllers including:
  • Fibaro Home Center 3/Lite
  • Fibaro Yubii Home

Configuring Z-Wave Devices:

Z-Wave devices often have several configurable parameters which you can change using your Vera?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active for or the type of manual switch connected to a Z-Wave light controller. Every available configurable parameter is listed in your device?s user manual. In most cases your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section. Please check the maximum load before installing or operating. This device must be installed by a certified electrician. For all warranty claims, an electrical compliance certificate from your electrician must be provided.

Technical Specifications

RF Protocol Z?Wave
RF Frequency 921.42Mhz ? AU/NZ ?approved RF for Z?wave
Z?Wave device type Z-Wave dimmer
Power 12V and 24V
Operation Range Up to 50m outdoors, up to 30m indoors (depending on terrain and building structure)
Application Controlled automatically by pre-set Fibaro devices or manually using any Z-Wave controller
Operation temperature 0 ~ 55 ?C
Storage temperature ?10 ~ 80 ?C
Weight 50g
Housing ABS
Compliance EN 55015, EN 60669-2-1
Regulatory Compliance Mark N5496

Documentation

FIBARO Z-Wave RGBW Controller User Manual
Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information