The Fibaro Z-Wave Single Switch 2 is a wireless Z-Wave module which can control appliances or lighting up to a maximum load of 2.0kW.
Control the ON-OFF function of a circuit remotely or using a wall switch
Compatible with all Z-Wave networks
Acts as a repeater expanding your Z-Wave network
Wide range of compatibility with existing light fittings and does NOT require expensive cabling
control loads up to 2kW (8A)
The main differences in the FGS-213 are:
Z-Wave Plus certification
Has power monitoring
230V powered only (this is the same as the FGS-212)
No dry contacts – this is important. It means that the new FGS-213 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
The Fibaro Z-Wave Single Switch 2 is a smart Z-Wave module capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.
The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.
This Fibaro Z-Wave Single Switch 2 requires 3-wire (including neutral) installation and works with an AC (110-230V) or DC (24-60V) power supply.
The Fibaro Z-Wave Single Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits.
This product integrates with all Australian certified (921.42MHz) Z-Wave controllers including:
Raspberry PI with RaZberry Card
Fibaro Home Controller 2/Lite
DHS Z-Wave Universal Remote Controller
DHS Z-Wave Mini Remote Controller
Configuring Z-Wave Devices
Z-Wave devices often have several configurable parameters which you can change using your Vera?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller.
Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section.
Please check the maximum load before installing or operating. This installation must be done by a certified electrician in Australia and New Zealand. Before engaging an electrician, check that they provide an electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician.
The Fibaro Z-Wave Single Switch 2 is a wireless Z-Wave module which can control appliances or lighting up to a maximum load of 2.0kW.
Control the ON-OFF function of a circuit remotely or using a wall switch
Compatible with all Z-Wave networks
Acts as a repeater expanding your Z-Wave network
Wide range of compatibility with existing light fittings and does NOT require expensive cabling
control loads up to 2kW (8A)
The main differences in the FGS-213 are:
Z-Wave Plus certification
Has power monitoring
230V powered only (this is the same as the FGS-212)
No dry contacts - this is important. It means that the new FGS-213 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
The Fibaro Z-Wave In-Wall Dimmer 2 (FGD-212) is the newest version of a popular wireless controller designed to operate behind a wall switch.
Control the level of illumination of your light remotely or using a manual button (in two and three way configurations)
Implemented algorithm of smart light source detection
Acts as a repeater expanding your Z-Wave network
Wide range of compatibility with existing light fittings and does NOT require expensive re-wiring
Active power and energy metering functionality
Works with various types of manual buttons
Active element: semiconductor electronic switch
The absolute best selling?QUBINO Z-Wave Dimmer 0-10V?(by GOAP) is unique. This Z-Wave product was developed to cater for the needs of Smart Home users looking for a Z-Wave solution that controls devices such as lights, fans and similar products with a 0-10V signal.?The QUBINO Flush Dimmer 0-10V is ideal for remotely dimming LED lights with low voltage ballast.
QUBINO?modules are ?install-and-forget? products. QUBINO are made to last, so we only select and use top-quality electronic components. These modules are also the most tested Z-Wave microcontrollers on the market. The Slovenian Institute of Quality and Metrology (SIQ), an independent testing body, tests safety parameters including temperature rise, construction, insulation resistance, power consumption and overload in accordance with the EN 60669-2-1 standard.
QUBINO Ltd. is a European company with 26-years experience in the automation field. With their expertise and passion for innovation in automation, they have developed a unique, ready to sell, certified and reliable portfolio of 14 Z-Wave wireless Smart Home products under different brands and OEMs around the world.
Control any switch. From anywhere.?Wirelessly.
Power sockets and light switches: amazing inventions. They literally changed the world. But if you?re not standing right next to them or can?t reach them, they?re limited.?No more. The future is smarter. So is your home. The?AEOTEC Nano Switch InWall?offers completely wireless control of your switches and sockets.
The?AEOTEC Nano Switch?offers total control, easily. Impossibly small, each?AEOTEC Nano Switch?installs invisibly behind any of your home?s existing switches or power sockets. Simply unscrew the faceplate, install the?AEOTEC Nano Switch?behind it, and you now have complete wireless control. Your old switches are instantly modern and instantly connected.
Shelly 1 Smart Home Automation WiFi Switch Compatible with Alexa and Google Home
Schedule Function: Set timer and countdown, create scenes, you can set timer schedules to automatically turn on/off your light, fans, or appliances according to your daily habits with the?Shelly 1 Wifi Switch. For example, you can set the corridor lights to turn on when you come back home at night and to turn off when you leave home
Voice Control: Shelly 1 Wifi Switch works with Alexa, Google Home and IFTTT, instead of reaching for the switch button every time, you can easily turn on/off the home appliances by your voice command, no hub required, create scenes on Alexa or Google Home, very convenient especially when your hands are full
App Control from Anywhere: You can control lights, routers, fans, TV, coffee maker or any other appliance under 16A/3500W remotely with a single press on the mobile app Shelly even you're away. No hub required, compatible with most Wifi routers (only with 2.4GHz wireless network)
Group Control: Create a group for all smart relays for one press control, one smart relay can be controlled by multiple mobile phones, share it with your family, everyone can control it easily. Perfect for hard-to-reach appliances & devices without ON/OFF switches
Compact Design: Compact smart relay switch can be installed in the junction box and make your outlet and switch smart while retaining manual control buttons. An essential accessory for your home automation system.
WiFi-operated Relay Switch
Control a wide range of home appliances and office equipment (lights, power lines, garage doors, curtains, security systems, heating radiators, air conditioners, etc.)? from anywhere with the smallest WiFi-operated relay switch.
Shelly 1 Wifi Switch Open Source
has an embedded webserver
has been designed for installation in a limited space, such as wall mounts, electrical control panels, etc.
can function as a standalone device, as an accessory to a home automation controller, or it may be used as another automation system's component.
This product is approved for use in Australia but must be installed by a licensed electrician.
SHELLY 2.5 RELAY SWITCH, ROLLER SHUTTER 2X10A
Wi-Fi Connected
For two electrical circuits (up to 2.3 kW each) with energy consumption monitoring
Mobile App Control
REST API to connect Shelly with your existing home automation system
Wide range of AC and DC power supply: 110-230V ? 10, 50 / 60Hz AC or 24-60V DC
Control a wide range of home appliances and office equipment (lights, power lines, garage doors, curtains, security systems, heating radiators, air conditioners, etc.) from anywhere with the smallest WiFi-operated double relay switch with roller shutter functionality in the world ? Shelly 2.5
Has an embedded web server;
Has been designed for installation in a limited space, such as wall mounts, electrical control panels, etc;
Can be used for two electrical circuits (up to 2.3 kW each) with energy consumption monitoring for each channel, overload, and temperature protection.
Can operate as a bi-directional motor control module (for drapes, blinds, garage doors, etc.).
Can function as a standalone device, as an accessory to a home automation controller, or it may be used as another automation system?s component.
TECHNICAL SPECIFICATIONS
Intelligent On/Off
Power Supply: 110-230V ?10, 50/60Hz AC and 24-60V DC
Compatible with all major international voltage standards.
2 Channels ? Maximum load current per output: 10A / 230V 50/60Hz.
Complies with the following EU standards: RE Directive 2014/53/EU, LVD 2006/95/WE, EMC 2004/108/WE, RoHS2 2011/65/UE
Operational temperature: -40 to +40 ?C
Dimensions (LxWxH): 39 x 36 x 17 mm
Minimum mounting opening: ? ? 50mm
Radio signal power: 1mW
Wireless/WiFi Protocol: 802.11 b/g/n
Radio frequency: 2400 ? 2500 MHz
Range: up to 50 m outdoors and up to 30 m indoors (depending on the building materials)
Electrical power consumption < 1 W
Microprocessor control
Independent dual power metering for each channel
Overload and temperature protection
Can connect to any Wi-Fi network or can operate as an Access Point
Controlled via WiFi and a mobile phone, computer, automation system or any other device supporting HTTP and/or UDP protocol
Controlled elements: 2 electrical circuits
Executive elements: 2 relays
Can be operated along with momentary keys or push-button switches
Has an integrated precise power meter.
This product is approved for use in Australia but must be installed by a licensed electrician.
Content
Product Details
The Fibaro Z-Wave Single Switch 2 is a smart Z-Wave module capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.
The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.
This Fibaro Z-Wave Single Switch 2 requires 3-wire (including neutral) installation and works with an AC (110-230V) or DC (24-60V) power supply.
The Fibaro Z-Wave Single Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits.
This product integrates with all Australian certified (921.42MHz) Z-Wave controllers including:
Raspberry PI with RaZberry Card
Fibaro Home Controller 2/Lite
DHS Z-Wave Universal Remote Controller
DHS Z-Wave Mini Remote Controller
Configuring Z-Wave Devices
Z-Wave devices often have several configurable parameters which you can change using your Vera?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller.
Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section.
Please check the maximum load before installing or operating.This installation must be done by a certified electrician in Australia and New Zealand.Before engaging an electrician, check that they provide an electrical compliance certificate.For a warranty claim, you have to provide an installation compliance certificate from your electrician.
The Fibaro Z-Wave In-Wall Dimmer 2 is designed to operate with or without a neutral wire. It may be used as a switch in systems without a neutral wire.
In the case of a 2-wire connection (no neutral), the Fibaro Z-Wave In-Wall Dimmer 2 may require a minimum load of 50W depending on the specifics of the connected load.
When used with a Fibaro Dimmer Bypass 2 it may operate with any compatible (see below) load from 5W. Before committing to buy Fibaro Dimmer Bypass 2 please check if your load can be properly controlled by Fibaro Dimmer 2 without a bypass device.
Do not connect this device to a power supply without a load. Only lighting devices may be connected to this device.
As a dimmer it operates with the following loads:
230V operated conventional incandescent (from 50W to 250W)
230V operated halogen (from 50W to 200W)
12 V operated ELV halogen lamps and dimmable LED lamps (with electronic transformers: Trailing and Leading-edge type) (from 50W to 200W)
Dimmable CFL tube lamps with electronic ballast only (from 50W to 200W)
As a switch it operates with the following loads:
Compact fluorescent lamps with electronic ballast
LED bulbs (power factor >0.7)
Fluorescent tube lamps with electronic ballast
Please note: For loads other than resistive do not exceed a 1.5A current.
This product integrates with all Australian certified (921.42 MHz) Z-Wave and Z-Wave Plus controllers including:
Vera Plus/ Edge
Fibaro Home Center 2 / Lite
Please note: Do not mix the load type (e.g. LED and CFL or different types of transformers) as it will impede the proper operation of the dimmer. Doing so will void the dimmer's warranty.
This product must be installed by a qualified electrician.Before engaging an electrician, check that they provide a warranty and electrical compliance certificate.For a warranty claim, you have to provide an installation compliance certificate from your electrician.PLEASE NOTE FOR THE INSTALLATIONS IN THE AREAS WHERE ELECTRICITY SUPPLIERS USE OFF-PEAK RIPPLE CONTROL SIGNALS:
Electricity suppliers in particular areas of Australia such as NSW, QLD and some other places are injecting an off-peak ripple control signal using Zellweger equipment or similar onto their distribution networks in order to remotely control devices such as off-peak hot water systems and street lighting, although other areas within Australia also use this technology. Not all properties are affected by ripple control, so just because you might live in one of these areas, does not mean that you will have these problems.
Ripple injection control systems work by superimposing coded control signals, commonly 750Hz or 1050Hz on the 50 Hz mains supply.
Some electrical appliances such as fans, dimmers, toasters and LED lighting can be sensitive to this ripple control signal. The results could be audible buzzing noises from fans or flickering lights whenever the ripple control signals are present.
Electricity suppliers are advising users to install appropriate ripple signal filters in such areas.
The ripple signal filter is a tuned passive inline filter that completely eliminates the superimposed ripple injection control signal from the normal mains supply to produce a noise free filtered mains supply which can then be connected to the electrical appliances or light control systems. The ripple signal filter is specifically tuned to eliminate the ripple control signal frequency of 750Hz or 1050Hz.
However, we can?t guarantee the ripple signal filter always will help you if you experiencing such issues. Please contact your local energy provider to get more information and proposed solutions for your electrical installation.
If you are getting similar problems with your dimmers and fans and it?s not Ripple Control Signal and you are hearing the tones at random times of the day, your electrical supply may be affected by harmonics; a power fluctuation that is not part of the normal electricity supply or ripple control signal output.
Harmonics are caused by interference created by other equipment on the network, such as inverter type air conditioners and switch mode power supplies for computers.
The offending appliances may be in your home or other premises on the local power grid. If you are being affected by network harmonics, it may be of benefit to transfer the electricity supply to your premises to a different phase in the street. This is something you will need to discuss with your electrical company.
We are strongly recommending for the areas we have mentioned above to run tests with only a few dimmers before committing for high volumes. If results are not fully OK you may use relays only instead of dimmers.
Please note that our warranty for the faulty devices is not covering above mentioned conditions with your local electric grids.
Please see affected with Ripple Signalling areas here:
QUEENSLAND
Only Southern Queensland (Energex) has Ripple Signalling.
The Frequency is 1050Hz.
The rest of Queensland (Ergon) does not have Ripple Signalling.
Unlimited controlling capability through a gateway
Z-Wave Plus compliant
23 additional parameters for expert users
Product Support
Please note:?If you are installing the entire Z-Wave? system for the first time, please refer to?the installation guide of your Z-Wave gateway before installing this device.
The GOAP Flush Dimmer uses a unique MOSFET 'trailing edge' dimmer to enable it to work with a huge range of bulb types:
Halogen and Incandescent (230V)
Dimmable LEDs (230V)
Dimmable CFL and Fluorescent (230V)
Low Voltage Halogen (24V)
Low Voltage LED (24V)
The QUBINO Z-Wave Dimmer can be used in the 230V mains lighting system where it uses a 'Trailing Edge' style dimmer to control the lights. It can also be used in a 24V low-voltage system where it uses PWM style control of the bulbs.
Please note: These devices require a 3-wire system (including neutral), please check your installation before purchasing. If you have a 2-wire system (without neutral) we recommend you use a FIBARO Z-Wave Dimmer 2.
Technical Specification
RF Protocol
Z-Wave Plus?, SDK version: 6.51.03
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Application
Indoor use only
Power
12-24 VDC
Operation Range
Up to 50m indoors with no obstacles
Enclosure
Plastic
Compliance
EN 60669-2-1
Operating Temp.
?-10C ~ +50C
Max. control voltage ratings
-20/+20VDC
Control signal range
0-11VDC
Max. sinking current
2 mA
Max. sourcing current
10 mA
Dimensions
41.8 mm x 36.8 mm x 15.4 mm
Product Description
Once installed behind a switch or socket, the?AEOTEC Nano Switch?offers unparalleled wireless control via Z-Wave protocol. It lets you control, automate, and monitor your lights light and power sockets. From anywhere. Anytime. And it does it all through enhancement ? with the?AEOTEC Nano Switch, your sockets and switches don?t have to be replaced and they?ll continue to offer the same manual control that you?re used to.
Product Support
Since the AEOTEC Nano Switch also supports the 24VDC power input,? you can also use it to control loads powered by 24VDC?(see user manual)
Manuals:?? Aeotec Nano Switch product manual