QUBINO Z-Wave 2 Relays

 

$85.99

Availability: In Stock

The QUBINO Double Switch (by GOAP) is a Z-Wave module for switching on/off one or two electrical devices (e.g. light, fan, etc …). The module can be controlled either through the Z-wave network or through the wall switch manually.

This module is designed to be mounted behind a traditional wall switch. The module measures the power consumption of load and supports the connection of the digital temperature sensor. It is designed to act as a repeater in order to improve the range and stability of the Z-Wave network.

Supported switches

The module supports mono-stable switches (push button) and bi-stable switches. The module is factory set to operate with bi-stable switches.

Discount per quantity

Quantity 4 - 7 8+
Price $81.69 $77.39
% Discount 5% 10%

Buy More for Bigger Savings!

20 in stock

SKU: DHS-LIT-SWW-QUB-02 Categories: , Tags: , ,

Description

• Compatible with any Z-Wave Controller.
• Dimensions (W x H x D) 41,8 x 36,8 x 15,4mm
• Power monitoring accuracy P=5-50W, +/-3W; P˃50W, +/-3%;
• Digital temperature sensor range (sensor must be ordered separately) -50 ~ 125°C
• Support for the connection of digital temperature sensor (optional part)
• 2 binary inputs offer the option to connect additional devices such as sensors, switches/pushbuttons, etc, …

Strengthens Z-Wave Connectivity

The smart relay module has been designed to work as a Z-Wave repeater, thereby providing you with the flexibility to extend the range of your Z-Wave network.

The QUBINO double switch is Z-Wave Plus Certified. Z-Wave Plus (5th Generation Z-Wave) offers a lot of new features including increased range, extended battery life and Over The Air upgrading (OTA). Take a look at our “What is Z-Wave Plus” guide for more information.

Note!

Do not connect the module to loads exceeding recommended values. Connect the module only in accordance with the manual and diagrams below. Use only qualified electricians!

Technical Specification

Product Name 
Z-Wave Dbl Switch
Powered by
24V DC or 240V AC
Operation Range
30m
Max Load
2300W (230VAC)
Radio frequency
921.42 MHz (AU/NZ Z-Wave)
Power Consumption
0,4W
Operation temperature
-10 -+40 C*
Measured temperature range 0,5o C (within 0o C – 40o C range) (optional sensor)
Temperature measuring accuracy
0,5 C
Housing
ABS
Dimensions (W x H x D)
41.8 x 36.8 x 15.4 mm

Quick Comparison

SettingsQUBINO Z-Wave 2 Relays removeFIBARO Z-Wave Dimmer 2 removeFIBARO Z-Wave Double Switch 2 removeAEOTEC WallMote Double removeAEOTEC Nano Dbl Switch InWall removeSHELLY PLUS 1 WiFi Switch remove
Image
SKUDHS-LIT-SWW-QUB-02DHS-LIT-DMW-FIB-02DHS-LIT-SWW-FIB-022DHS-CON-SCON-AEO-02DHS-LIT-SWW-AEO-02SH-SHELLY1+
Rating
Price$85.99$98.99$89.99$108.00$94.99$24.99
Stock

20 in stock

20 in stock

20 in stock

Out of stock

4 in stock

50 in stock (can be backordered)

Availability20 in stock20 in stock20 in stockOut of stock4 in stock50 in stock (can be backordered)
Add to cart

Add to basket

Add to basket

Add to basket

Read more

Add to basket

Add to basket

DescriptionThe QUBINO Double Switch (by GOAP) is a Z-Wave module for switching on/off one or two electrical devices (e.g. light, fan, etc ...). The module can be controlled either through the Z-wave network or through the wall switch manually. This module is designed to be mounted behind a traditional wall switch. The module measures the power consumption of load and supports the connection of the digital temperature sensor. It is designed to act as a repeater in order to improve the range and stability of the Z-Wave network. Supported switches The module supports mono-stable switches (push button) and bi-stable switches. The module is factory set to operate with bi-stable switches.The Fibaro Z-Wave In-Wall Dimmer 2 (FGD-212) is the newest version of a popular wireless controller designed to operate behind a wall switch.
  • Control the level of illumination of your light remotely or using a manual button (in two and three way configurations)
  • Implemented algorithm of smart light source detection
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive re-wiring
  • Active power and energy metering functionality
  • Works with various types of manual buttons
  • Active element: semiconductor electronic switch
The new Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave wireless module which can control two circuits each with a maximum load of 6.5A per channel and 10A total load per circuit.
  • Control the ON-OFF function of two two independent circuits or appliances remotely or using a wall switch
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling
  • Latest generation Z-Wave 500 series chip
  • Z-Wave Plus certification
  • Very accurate energy measurement +/- 1 % for power above 5W
  • Supports secure mode (Z-Wave Network Security) encrypted with AES-128
  • No dry contacts - this is important. It means that the new FGS-223 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
On any wall. WallMote is the wall switch that you can install anywhere. Wirelessly. Whatever the room, whatever the wall, WallMote is perfect. The wireless Z-Wave wall switch that you can place anywhere, on any wall, with as little as double-sided tape. Unpack it. Stick it. Charge it. Control is just a tap away. ZW120a Simple to install. WallMote is the wall switch for anywhere because it is simple to install. Mounting it requires just two steps. Attach the mounting plate. WallMote’s mounting plate affixes to any wall or surface using custom mounting tape. Peel. Stick. Done. Attach WallMote. WallMote is attractive. Literally. Place it in front of the mounting plate, and it will magnetically attach.Control any switch. From anywhere. Wirelessly. Power sockets and light switches: amazing inventions. They literally changed the world. But if you’re not standing right next to them or can’t reach them, they’re limited. No more. The future is smarter. So is your home. The AEOTEC Dual Nano Switch InWall offers complete wireless control of your switches and sockets. ZW132d The AEOTEC Nano Switch offers total control, easily. Impossibly small, each AEOTEC Dual Nano Switch installs invisibly behind any of your home’s existing switches or power sockets. Simply unscrew the faceplate, install the AEOTEC Nano Switch behind it, and you now have complete wireless control. Your old switches are instantly modern and instantly connected.

WiFi-operated relay switch, 1 channel 16A

Control a wide range of home appliances and office equipment (lights, power lines, security systems, heating radiators, air conditioners, etc.) from anywhere in the world with the smallest WiFi-operated relay switch, with Bluetooth connection!
  • Wi-Fi operated - Connects to your Wi-Fi network. No HUB required!
  • Bluetooth - Add devices quick and easy via Bluetooth connection, using the Shelly Cloud App
  • Dry contacts
  • Low voltage support
  • Extremely fast processor – ESP32
  • Enhanced safety - Over-temperature protection
  • Enhanced security - MQTT and WSS support, TLS and custom certificates support
  • Improved API interface
  • Onboard scripting features to allow you to automate to your heart's content without any hub required.
Content
• Compatible with any Z-Wave Controller.
• Dimensions (W x H x D) 41,8 x 36,8 x 15,4mm
• Power monitoring accuracy P=5-50W, +/-3W; P˃50W, +/-3%;
• Digital temperature sensor range (sensor must be ordered separately) -50 ~ 125°C
• Support for the connection of digital temperature sensor (optional part)
• 2 binary inputs offer the option to connect additional devices such as sensors, switches/pushbuttons, etc, …
Strengthens Z-Wave Connectivity The smart relay module has been designed to work as a Z-Wave repeater, thereby providing you with the flexibility to extend the range of your Z-Wave network. The QUBINO double switch is Z-Wave Plus Certified. Z-Wave Plus (5th Generation Z-Wave) offers a lot of new features including increased range, extended battery life and Over The Air upgrading (OTA). Take a look at our "What is Z-Wave Plus" guide for more information. Note! Do not connect the module to loads exceeding recommended values. Connect the module only in accordance with the manual and diagrams below. Use only qualified electricians!

Technical Specification

Product Name 
Z-Wave Dbl Switch
Powered by
24V DC or 240V AC
Operation Range
30m
Max Load
2300W (230VAC)
Radio frequency
921.42 MHz (AU/NZ Z-Wave)
Power Consumption
0,4W
Operation temperature
-10 -+40 C*
Measured temperature range 0,5o C (within 0o C - 40o C range) (optional sensor)
Temperature measuring accuracy
0,5 C
Housing
ABS
Dimensions (W x H x D)
41.8 x 36.8 x 15.4 mm
The Fibaro Z-Wave In-Wall Dimmer 2 is designed to operate with or without a neutral wire. It may be used as a switch in systems without a neutral wire. In the case of a 2-wire connection (no neutral), the Fibaro Z-Wave In-Wall Dimmer 2 may require a minimum load of 50W depending on the specifics of the connected load. When used with a Fibaro Dimmer Bypass 2 it may operate with any compatible (see below) load from 5W. Before committing to buy Fibaro Dimmer Bypass 2 please check if your load can be properly controlled by Fibaro Dimmer 2 without a bypass device. Do not connect this device to a power supply without a load. Only lighting devices may be connected to this device. As a dimmer it operates with the following loads:
  • 230V operated conventional incandescent (from 50W to 250W)
  • 230V operated halogen (from 50W to 200W)
  • 12 V operated ELV halogen lamps and dimmable LED lamps (with electronic transformers: Trailing and Leading-edge type) (from 50W to 200W)
  • 12V operated MLV halogen lamps (with ferromagnetic transformers) (from 50W to 225W)
  • Dimmable CFL tube lamps with electronic ballast only (from 50W to 200W)
As a switch it operates with the following loads:
  • Compact fluorescent lamps with electronic ballast
  • LED bulbs (power factor >0.7)
  • Fluorescent tube lamps with electronic ballast
Please note: For loads other than resistive do not exceed a 1.5A current. This product integrates with all Australian certified (921.42 MHz) Z-Wave and Z-Wave Plus controllers including:
  • Vera Plus/ Edge
  • Fibaro Home Center 2 / Lite
Please note: Do not mix the load type (e.g. LED and CFL or different types of transformers) as it will impede the proper operation of the dimmer. Doing so will void the dimmer's warranty. This product must be installed by a qualified electrician. Before engaging an electrician, check that they provide a warranty and electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician. PLEASE NOTE FOR THE INSTALLATIONS IN THE AREAS WHERE ELECTRICITY SUPPLIERS USE OFF-PEAK RIPPLE CONTROL SIGNALS: Electricity suppliers in particular areas of Australia such as NSW, QLD and some other places are injecting an off-peak ripple control signal using Zellweger equipment or similar onto their distribution networks in order to remotely control devices such as off-peak hot water systems and street lighting, although other areas within Australia also use this technology. Not all properties are affected by ripple control, so just because you might live in one of these areas, does not mean that you will have these problems. Ripple injection control systems work by superimposing coded control signals, commonly 750Hz or 1050Hz on the 50 Hz mains supply. Some electrical appliances such as fans, dimmers, toasters and LED lighting can be sensitive to this ripple control signal. The results could be audible buzzing noises from fans or flickering lights whenever the ripple control signals are present. Electricity suppliers are advising users to install appropriate ripple signal filters in such areas. The ripple signal filter is a tuned passive inline filter that completely eliminates the superimposed ripple injection control signal from the normal mains supply to produce a noise free filtered mains supply which can then be connected to the electrical appliances or light control systems. The ripple signal filter is specifically tuned to eliminate the ripple control signal frequency of 750Hz or 1050Hz. However, we can’t guarantee the ripple signal filter always will help you if you experiencing such issues. Please contact your local energy provider to get more information and proposed solutions for your electrical installation. If you are getting similar problems with your dimmers and fans and it’s not Ripple Control Signal and you are hearing the tones at random times of the day, your electrical supply may be affected by harmonics; a power fluctuation that is not part of the normal electricity supply or ripple control signal output. Harmonics are caused by interference created by other equipment on the network, such as inverter type air conditioners and switch mode power supplies for computers. The offending appliances may be in your home or other premises on the local power grid. If you are being affected by network harmonics, it may be of benefit to transfer the electricity supply to your premises to a different phase in the street. This is something you will need to discuss with your electrical company. We are strongly recommending for the areas we have mentioned above to run tests with only a few dimmers before committing for high volumes. If results are not fully OK you may use relays only instead of dimmers. Please note that our warranty for the faulty devices is not covering above mentioned conditions with your local electric grids. Please see affected with Ripple Signalling areas here:

QUEENSLAND

  • Only Southern Queensland (Energex) has Ripple Signalling.
  • The Frequency is 1050Hz.
  • The rest of Queensland (Ergon) does not have Ripple Signalling.

NSW

  • Energy Australia Full Supply Area
  • Energy Australia Sydney &Hunter Supply Area

Documentation

Fibaro Z-Wave In-Wall Dimmer 2 Manual

Technical Specifications

RF Protocol
Z-Wave
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z‐wave device type
Z-Wave multiple level dimmer, routing slave
Power Supply
220 - 240V ~ 50Hz
Operation Range
Up to 30m indoors (depending on building materials)
Application
Indoor use only
Operation temperature
0 ~ 35 °C
Dimensions (L x W x H)
42.5mm x 38.25mm x 20.3mm
Weight
30g
Operational Current
0.25 - 1.1A
Compliance
RCM E3606
Dimming type compatibility
Leading and Trailing Edge

Product Details

The Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene. The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician. This Fibaro Fibaro Z-Wave Double Switch 2 requires 3-wire (including neutral) installation and works with an AC (230V) power supply. The Fibaro Z-Wave Double Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits. This product integrates with Australian certified (921.42 MHz) Z-Wave Controllers - Fibaro Home Center 2/Lite Note: It doesn't integrate with Vera gateways at this stage.

Configuring Z-Wave Devices:

Z-Wave devices often have several configurable parameters which you can change using Fibaro’s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller. Every available configurable parameter is listed in your device’s user manual. In most cases, your device’s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. Please check the maximum load before installing or operating. This installation must be done by a certified electrician in Australia and New Zealand. Before engaging an electrician, check that they provide an electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician.

Documentation

Fibaro Z-Wave Double Switch 2 Manual

Technical Specification

RF Protocol
Z-Wave
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z‐Wave device type
Z-Wave Switch, Routing Slave
Power
230V ± 10% 50/60 Hz
Operation Range
Up to 20 m indoors with no obstacles
Application
Indoor use only, up to 1.5kW resistive load per circuit
Operation temperature
0 ~ 55 °C
Storage temperature
-10 ~ 80 °C
Weight
50g
Housing
ABS
Compliance
EN 55015, EN 60669-2-1
Regulatory Compliance Mark
N5496
Dimensions
(LxWxH) 42mm x 37mm x 17mm

Product Description

Control on tap. Control one Z-Wave device. Control many. And all with a single tap. There is simplicity in tapping touch glass. smartphones proved it. There is power too. Each of WallMote’s buttons can be programmed to control one Z-Wave device or many. Meaning that a single tap on its smooth surface can change a single light, a whole room, or your whole home. Tap good morning. Tap good night. Tap all the moments in between. Tap. Control. ZW120c wallmote mountwallmote engineeringwallmote glass Control a light. Control a room. Control a home.Control a light. Control a room. Control a home. Because WallMote communicates directly with your Z-Wave gateway, it can be used to control anything that your gateway can. Even things that are not Z-Wave. Smart lighting from Philips Hue? Check. Connected music from Sonos? Easy. If it is connected to your gateway, simply add it to a scene that WallMote can control and it is on top. ZW120b Wireless switch. To be used anywhere in your home, WallMote and WallMote Quad need to be more than wireless. They need to be impressively wireless. Both switches offer a fine-tuned antenna capable of communicating over an open range of over 150 metres. Secure switch. Technology changes, now your wall switches change with it. WallMote and WallMote Quad are cutting-edge today and will be cutting-edge tomorrow. They are both capable of receiving wireless firmware updates via Z-Wave Plus so that they are always up to date. Subtle switch. Not just portable, but perfectly balanced. The minimalist design of both WallMote and WallMote Quad measures just 7.7cm wide and a slender 1.9cm deep Simple recharging. Battery powered but without the need to ever change a battery, WallMote and WallMote Quad are both powered by a rechargeable lithium battery designed for smartphones. It recharges just like a smartphone too via the provided micro USB cable. Haptic feedback. It is capable of controlling your whole home, so you may not even be present to see things change when you press WallMote’s touch glass. But you will feel the change. WallMote’s haptic engine confirms your every action via a click sensation. Gen5 built in. WallMote and WallMote Quad are part of Aeotec’s Gen5 range of Z-Wave devices. Built upon the latest version of Z-Wave- Z-Wave Plus – cutting-edge performance and security is crafted into Z-Wave’s most advanced battery-powered wall switch.

Product Support

Works with VeraAeotec Door Window Sensor 6 and Vera

Manuals

⇒  Aeotec WallMote product manual

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z‐Wave device type
Multilevel controller
Power
Rechargeable Lithium-ion
Operation Range
Up to 40m without obstacles
Application
Indoor use only
Operation temperature
0 ~ 55 °C
Storage temperature
-10 ~ 80 °C
Color
White
Weight
100g
Housing
ABS
Dimensions
(LxWxH) 72mm x 72mm x 9mm
Compliance
Z-Wave Plus certified
Warranty 12 Months

Product Description

Once installed behind a switch or socket, the AEOTEC Dual Nano Switch offers unparalleled wireless control via Z-Wave protocol. It lets you control, automate, and monitor your lights and power sockets. From anywhere. Anytime. And it does it all through enhancement – with the AEOTEC Nano Switch, your sockets and switches don’t have to be replaced and they’ll continue to offer the same manual control that you’re used to. ZW098 B22dd

Product Support

  Works with Vera Manuals: ⇒  Aeotec Dual Nano Switch product manuals

Technical Specification

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z-Wave device type
Switch
Power
240V AC
Operation Range
Up to 40m without obstacles
Application
Indoor use only
Operation temperature
0 ~ 55 °C
Storage temperature
-10 ~ 80 °C
Colour
white
Weight
50g
Housing
ABS
Size
42mm x 40mm x 25mm
Compliance
Z-Wave Plus certified
Warranty 12 Months

WiFi-operated relay switch, 1 channel 16A

Control a wide range of home appliances and office equipment (lights, power lines, security systems, heating radiators, air conditioners, etc.) from anywhere in the world with the smallest WiFi-operated relay switch, with Bluetooth connection!
  • Wi-Fi operated - Connects to your Wi-Fi network. No HUB required!
  • Bluetooth - Add devices quick and easy via Bluetooth connection, using the Shelly Cloud App
  • Dry contacts
  • Low voltage support
  • Extremely fast processor – ESP32
  • Enhanced safety - Over-temperature protection
  • Enhanced security - MQTT and WSS support, TLS and custom certificates support
  • Improved API interface
  • Onboard scripting features to allow you to automate to your heart's content without any hub required.
Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information