Aeotec Z-Wave Heavy Duty Smart Switch can switch powered electrical devices and appliances that draw up to 40 amps or 9600 Watts of power. Includes built-in Z-Wave signal repeater and extended Z-Wave wireless range (up to 150m outdoors). Rated IP44 for both outdoor and indoor use.
Electronics that use up to 40 amps of power. They?re the big electronics and appliances in your home. Big fridges and pool pumps. Hot water systems and electric car chargers.
If it?s big, if it uses a lot of power, Heavy Duty Smart Switch was made for it.
Requires professional installation.
The Aeotec Heavy Duty Smart Switch must be installed by a licensed electrician.
Warning:?Be careful of electric shock. Only installation and maintenance personnel should operate this button.
Please read this and other device guides carefully. Failure to follow the recommendations set forth by Aeotec Limited may be dangerous or cause a violation of the law. The manufacturer, importer, distributor, and/or reseller will not be held responsible for any loss or damage resulting from not following any instructions in this guide or in other materials.
A licensed electrician with knowledge and understanding of electrical systems and safety should complete the installation.
Keep product away from open flames and extreme heat. Avoid direct sunlight or heat exposure.
Heavy Duty Smart Switch Gen5 current?can not exceed 40 amps.
Aeotec Z-Wave Heavy Duty Smart Switch can switch powered electrical devices and appliances that draw up to 40 amps or 9600 Watts of power. Includes built-in Z-Wave signal repeater and extended Z-Wave wireless range (up to 150m outdoors). Rated IP44 for both outdoor and indoor use.
Electronics that use up to 40 amps of power. They?re the big electronics and appliances in your home. Big fridges and pool pumps. Hot water systems and electric car chargers.
If it?s big, if it uses a lot of power, Heavy Duty Smart Switch was made for it.
Requires professional installation.
The Aeotec Heavy Duty Smart Switch must be installed by a licensed electrician.
Three different sensors built into the?AEOTEC TriSensor's?small finish.
A motion sensor to monitor presence in your rooms, a temperature sensor to manage its environment, and a light sensor to manage connected lighting and shutters.
On any wall.
The?AEOTEC WallMote?is the wall switch that you can install anywhere. Wirelessly.
Whatever the room, whatever the wall, the?AEOTEC WallMote?is perfect. It is the wireless, Z-Wave wall switch that you can place anywhere, on any wall, with as little as double sided tape. Unpack it. Stick it. Charge it. Control is just a tap away.
Simple to install.
The?AEOTEC WallMote?is the wall switch for anywhere. You can mount it in just two steps!
Attach the mounting plate.
Attach the mounting plate. The?AEOTEC WallMote?s mounting plate affixes to any wall or surface using custom mounting tape. Peel. Stick. Done.
Attach WallMote.
The?AEOTEC WallMote?is attractive. Literally. Simply place it in front of the mounting plate and it will magnetically attach.
Stop dimmed lights flickering.
Dimming energy-saving lights is complicated ? there?s a lot of different technologies built into modern bulbs.
That?s why dimmed lights sometimes flicker or remain on ? power trickles through.?The?AEOTEC Dimmer Bypass?works with the?AEOTEC Nano Dimmer?to remove the signals from your power line that cause low-watt lightbulbs to flicker.
If you want to control low-voltage lighting that?uses less than 4 Watts?using an?AEOTEC Nano Dimmer?you will need to include the?AEOTEC Dimmer Bypass?in your installation to ensure the lights do not flicker.
Control any switch. From anywhere.?Wirelessly.
Power sockets and light switches: amazing inventions. They literally changed the world. But if you?re not standing right next to them or can?t reach them, they?re limited.
No more. The future is smarter. So is your home. The?AEOTEC Dual Nano Switch InWall?offers complete wireless control of your switches and sockets.
The?AEOTEC Nano Switch?offers total control, easily. Impossibly small, each?AEOTEC Dual Nano Switch?installs invisibly behind any of your home?s existing switches or power sockets. Simply unscrew the faceplate, install the?AEOTEC Nano Switch?behind it, and you now have complete wireless control. Your old switches are instantly modern and instantly connected.
The AEOTEC Nano Dimmer InWall dramatically improves the lighting in your home. Aeotec 3rd generation of invisible lighting controllers outperforms all that has come before it. Dimming is smoother. Compatibility is broader. Lighting is faster and more responsive. Automation and intelligence have never been more powerful. And it comes in such a small size, that you?ll be amazed at just how much functionality we were able to craft inside.
Perfect lighting is a part of every truly smart home. Lighting that is responsive. That is always the right brightness. That is always on when you need it, and off when you don?t. But perfect lighting has never been easy.
Instead, perfect lighting has been too complicated to achieve. In the past, to automate your lights with Z-Wave you?ve had to worry about the type of wiring you have, whether your lighting is trailing or leading edge, and whether you?re using TRIACs or thyristors. Far too complicated. Get any of those wrong and your connected lighting would quickly become a connected headache.
No more. Nano Dimmer offers smart, connected lighting without any of the hassles.
Content
Product Description
Important safety information.Warning:?Be careful of electric shock. Only installation and maintenance personnel should operate this button.
Please read this and other device guides carefully. Failure to follow the recommendations set forth by Aeotec Limited may be dangerous or cause a violation of the law. The manufacturer, importer, distributor, and/or reseller will not be held responsible for any loss or damage resulting from not following any instructions in this guide or in other materials.
A licensed electrician with knowledge and understanding of electrical systems and safety should complete the installation.
Keep product away from open flames and extreme heat. Avoid direct sunlight or heat exposure.
Heavy Duty Smart Switch Gen5 current?can not exceed 40 amps.
Contains small parts; keep away from children.
Motion sensor
Motion sensor. Motion for security. Motion for presence. Motion for management. The?AEOTEC TriSensor?is perfect for more than just an intelligent security system. With a 7 metre range, the AEOTEC TriSensor?captures motion data that can be used for everything from security to heating management to energy saving. Knowing if a room is occupied or a hall is being used is a powerful piece of data.
The?AEOTEC TriSensor?makes your home automation system more powerful and more intelligent.
Temperature sensor.
From motorised curtains and windows to fans and thermostats, there are a lot of ways that you can use Z-Wave to keep the temperature of a room absolutely perfect. The?AEOTEC TriSensor?provides the intelligence to do just that. Within each sensor is an incremental temperature sensor capable of accurately measuring between -15~50 ?C and reporting those temperature changes back to a smart home gateway.
Light sensor.
Automated lighting is only as smart as the system that powers it. With the?AEOTEC TriSensor's digital light sensor measuring the level of light in a room, your home control system will be able to intelligently maintain its ambience. From opening and closing curtains to setting lights to be the perfect level be it day or night, the AEOTEC TriSensor?is the smarts behind smart lighting.
The perfect sensor comes with the perfect accessories. The?AEOTEC TriSensor?has three different accessories, each designed to make the installation of the sensor perfect for your home.
Place it anywhere.
Recessor.?(sold separately)
Install the?AEOTEC TriSensor?in a ceiling or wall cavity with a recessor (sold separately) and just 12 mm will extrude. Features magnetic clasps for simple removal of the sensor.
Mounting arm.
Discrete and for corner installations, the mounting arm allows you to rotate your?AEOTEC TriSensor to best ensure motion is detected when you want it to be.
Tape.
Weighing only 52 grams, the?AEOTEC TriSensor can be easily installed with just the provided double-sided tape from 3M.
Control on tap.
Control one Z-Wave device. Control many. And all with a single tap.
There is simplicity in tapping touch glass. smartphones proved it. There is power too. Each of your?AEOTEC WallMote?s buttons can be programmed to control one Z-Wave device or many. Meaning that a single tap on its smooth surface can change a single light, a whole room, or your whole home. Tap good morning. Tap good night. Tap all the moments in between.
Control a light. Control a room. Control a home.
Because the?AEOTEC WallMote?communicates directly with your Z-Wave gateway, it can be used to control anything that your gateway can. Even things that are not Z-Wave. Smart lighting from Philips Hue? Check. Connected music from Sonos? Easy. If it is connected to your gateway, simply add it to a scene that WallMote can control and it is on top.
Wireless switch.
To be used anywhere in your home, WallMote and WallMote Quad need to be more than wireless. They need to be impressively wireless. Both switches offer a fine-tuned antenna capable of communicating over an open range of over 150 metres.
Secure switch.
Technology changes, now your wall switches change with it. WallMote and WallMote Quad are cutting-edge today and will be cutting-edge tomorrow. They are both capable of receiving wireless firmware updates via Z-Wave Plus so that they are always up to date.
Subtle switch.
Not just portable, but perfectly balanced. The minimalist design of both WallMote and WallMote Quad measures just 7.7cm wide and a slender 1.9cm deep
Simple recharging.
Battery powered but without the need to ever change a battery, WallMote and WallMote Quad are both powered by a rechargeable lithium battery designed for smartphones. It recharges just like a smartphone too via the provided micro USB cable.
Haptic feedback.
It is capable of controlling your whole home, so you may not even be present to see things change when you press WallMote?s touch glass. But you will feel the change. WallMote?s haptic engine confirms your every action via a click sensation.
Gen5 built in.
WallMote and WallMote Quad are part of Aeotec?s Gen5 range of Z-Wave devices. Built upon the latest version of Z-Wave- Z-Wave Plus ? cutting-edge performance and security is crafted into Z-Wave?s most advanced battery-powered wall switch.
Compatible bulbs.
There are a lot of different types of low-power light bulbs that your home may have; Bypass has been designed to work with most of them. It?s been designed to stop most bulbs from flickering including?static and dimmable LEDs and CFLs.
Once installed behind a switch or socket, the?AEOTEC Dual Nano Switch offers unparalleled wireless control via Z-Wave protocol. It lets you control, automate, and monitor your lights and power sockets. From anywhere. Anytime. And it does it all through enhancement ? with the AEOTEC Nano Switch, your sockets and switches don?t have to be replaced and they?ll continue to offer the same manual control that you?re used to.
Nano Dimmer lets you add new and existing lights to your Z-Wave system. It makes your lights smarter. It makes them responsive. It gives you the ability to control them, schedule, dim them and brighten them.
All that control and intelligence comes from simply wiring Nano Dimmer behind an existing wall switch.
PLEASE NOTE FOR THE INSTALLATIONS IN THE AREAS WHERE ELECTRICITY SUPPLIERS USE OFF-PEAK RIPPLE CONTROL SIGNALS:
Electricity suppliers in particular areas of Australia such as NSW, QLD and some other places are injecting an off-peak ripple control signal using Zellweger equipment?or similar onto their distribution networks in order to remotely control devices such as off-peak hot water systems and street lighting, although other areas within Australia also use this technology. Not all properties are affected by ripple control, so just because you might live in one of these areas, does not mean that you will have these problems.
Ripple injection control systems work by superimposing coded control signals, commonly 750Hz or 1050Hz on the 50 Hz mains supply.
Some electrical appliances such as fans, dimmers, toasters and LED lighting can be sensitive to this ripple control signal. The results could be audible buzzing noises from fans or flickering lights whenever the ripple control signals are present.
Electricity suppliers are advising users to install appropriate?ripple signal filters in such areas.
The ripple signal filter is a tuned passive inline filter that completely eliminates the superimposed ripple injection control signal from the normal mains supply to produce a noise-free filtered mains supply which can then be connected to the electrical appliances or light control systems. The ripple signal filter is specifically tuned to eliminate the ripple control signal frequency of 750Hz or 1050Hz.
However, we can?t guarantee the ripple signal filter always will help you if you experiencing such issues. Please contact your local energy provider to get more information and proposed solutions for your electrical installation.
If you are getting similar problems with your dimmers and fans and it?s not Ripple Control Signal and you are hearing the tones at random times of the day, your electrical supply may be affected by harmonics; a power fluctuation that is not part of the normal electricity supply or ripple control signal output.
Harmonics are caused by interference created by other equipment on the network, such as inverter type air conditioners and switch-mode power supplies for computers.
The offending appliances may be in your home or other premises on the local power grid. If you are being affected by network harmonics, it may be of benefit to transfer the electricity supply to your premises to a different phase in the street. This is something you will need to discuss with your electrical company.
We are strongly recommending for the areas we have mentioned above to run tests with only a few dimmers before committing for high volumes. If results are not fully OK you may use relays only instead of dimmers.Please note that our warranty for the faulty devices is not covering above-mentioned conditions with your local electric grids.
Please see affected with Ripple Signalling areas here:
QUEENSLAND
Only Southern Queensland (Energex) has Ripple Signalling.
The Frequency is 1050Hz.
The rest of Queensland (Ergon) does not have Ripple Signalling.