FIBARO Double Smart Module FGS224

$84.99

Availability: In Stock

The new FIBARO Double Smart Module(FGS-224) is a smart Z-Wave wireless module that can control two circuits each with a maximum load of 6A per channel and 9.5A total load per circuit.

  • Control the ON-OFF function of two independent circuits or appliances remotely or using a wall switch
  • Can be used as voltage free relays (dry contacts)
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling
  • Latest generation Z-Wave 500 series chip
  • Z-Wave Plus certification
  • Very accurate energy measurement +/- 1 % for power above 5W
  • Supports secure mode (Z-Wave Network Security) encrypted with AES-128
  • Dry contacts – this is important. It means that the new FGS-224 can be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.

Discount per quantity

Quantity 4 - 7 8+
Price $80.74 $76.49
% Discount 5% 10%

Buy More for Bigger Savings!

8 in stock

SKU: DHS-LIT-SWW-FIB-224 Categories: , Tag:

Description

The FIBARO Double Smart Module(FGS-224) is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.

The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.

This FIBARO Double Smart Module (FGS-224) requires 3-wire (including neutral) installation and works with an AC (230V) power supply.

FIBARO

The FIBARO Double Smart Module (FGS-224) also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits.

This product integrates with Australian certified (921.42 MHz) Z-Wave Controllers – Fibaro Home Center 3/2/Lite

Configuring Z-Wave Devices:

Z-Wave devices often have several configurable parameters which you can change using Fibaro?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller.

Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device.

Please check the maximum load before installing or operating.?
This installation must be done by a certified electrician in Australia and New Zealand.
Before engaging an electrician, check that they provide an electrical compliance certificate.
For a warranty claim, you have to provide an installation compliance certificate from your electrician.

Documentation

FIBARO Double Smart Module Manual

Technical Specifications

RF Protocol
Z-Wave
RF Frequency
921.42Mhz – AU/NZ ?approved RF for Z-wave
Z?Wave device type
Z-Wave Switch, Routing Slave
Power
230V?? 10% 50/60 Hz
Operation Range
Up to 20 m indoors with no obstacles
Application
Indoor use only, up to?1.5kW resistive load per circuit

6A per one channel, 9.5A total

Operation temperature
0 ~ 55 ?C
Storage temperature
-10 ~ 80 ?C
Weight
50g
Housing
ABS
Compliance
EN 55015, EN 60669-2-1
Regulatory Compliance Mark
N5496
Dimensions
(LxWxH) 42mm x 37mm x 17mm

Quick Comparison

SettingsFIBARO Double Smart Module FGS224 removeFIBARO Z-Wave RGBW Controller 2 removeFIBARO Z-Wave Button (White) removeFIBARO Z-Wave Double Switch 2 removeFIBARO D/W Sensor 2 (White) removeFIBARO Z-Wave Flood Sensor remove
Image
SKUDHS-LIT-SWW-FIB-224DHS-LIT-RGBW-FIBDHS-CON-SBUT-FIB-WHDHS-LIT-SWW-FIB-022DHS-SNS-DW-FIB-WH-02DHS-SNS-FL-FIB
Rating
Price$84.99$84.99$78.00$84.99$73.99$99.99
Stock

8 in stock

2 in stock

3 in stock

20 in stock

Out of stock

1 in stock

Availability8 in stock2 in stock3 in stock20 in stockOut of stock1 in stock
Add to cart

Add to basket

Add to basket

Add to basket

Add to basket

Read more

Add to basket

DescriptionThe new FIBARO Double Smart Module(FGS-224) is a smart Z-Wave wireless module that can control two circuits each with a maximum load of 6A per channel and 9.5A total load per circuit.
  • Control the ON-OFF function of two independent circuits or appliances remotely or using a wall switch
  • Can be used as voltage free relays (dry contacts)
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling
  • Latest generation Z-Wave 500 series chip
  • Z-Wave Plus certification
  • Very accurate energy measurement +/- 1 % for power above 5W
  • Supports secure mode (Z-Wave Network Security) encrypted with AES-128
  • Dry contacts - this is important. It means that the new FGS-224 can be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
The FIBARO Z-Wave RGBW Controller 2 is a wireless controller which enables you to manage your LED strips and halogen lights.
  • Wirelessly control LEDs with an unlimited range of colour options
  • Monitors energy usage
  • Four analogue sensor inputs
  • Four dimmer channels
  • Acts as a repeater expanding your Z-Wave network
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
  • Completely wireless
  • Z-Wave Plus certified
  • Supports 6 different actions/scenes
  • Available in multiple colours (white, black, red, blue, yellow)
The new Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave wireless module which can control two circuits each with a maximum load of 6.5A per channel and 10A total load per circuit.
  • Control the ON-OFF function of two two independent circuits or appliances remotely or using a wall switch
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling
  • Latest generation Z-Wave 500 series chip
  • Z-Wave Plus certification
  • Very accurate energy measurement +/- 1 % for power above 5W
  • Supports secure mode (Z-Wave Network Security) encrypted with AES-128
  • No dry contacts - this is important. It means that the new FGS-223 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
The FIBARO Z-Wave D/W Sensor 2 is a small, battery powered magnetic door and window sensor with a built in temperature sensor.
  • Completely wireless
  • Automatic software updates
  • Includes a built in temperature sensor
  • Comes in multiple colours
  • Tamper and low battery alarm notification
Fibaro Flood Sensor is a universal, Z-Wave compatible, flood and temperature sensor. Device can be battery (ca. 2 years battery life) or VDC powered (12 or 24 VDC). A flood alarm is sent to the Z-Wave network devices or additionally to any alarm system controller, through opening an NC contact. The device has built in temperature sensor, monitoring the temperature of e.g. floor. Fibaro Flood Sensor is designed to be placed on the floor or on a wall with a flood sensor probe extended by a connected wire. The device has built in LED indicator and acoustic alarm. In addition, the sensor is equipped with a tilt sensor reporting tilt or movement to the main controller e.g. when someone has taken the Sensor from its original location. LED diode signals flood, operating mode or the Z-Wave network communication range. Fibaro Flood Sensor is sink-proof, which means it drifts on the water surface and keeps on sending alarm signals in case of substantial inundation of water.
ContentThe FIBARO Double Smart Module(FGS-224) is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene. The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician. This FIBARO Double Smart Module (FGS-224) requires 3-wire (including neutral) installation and works with an AC (230V) power supply. The FIBARO Double Smart Module (FGS-224) also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits. This product integrates with Australian certified (921.42 MHz) Z-Wave Controllers - Fibaro Home Center 3/2/Lite

Configuring Z-Wave Devices:

Z-Wave devices often have several configurable parameters which you can change using Fibaro?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller. Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. Please check the maximum load before installing or operating.? This installation must be done by a certified electrician in Australia and New Zealand. Before engaging an electrician, check that they provide an electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician.

Documentation

FIBARO Double Smart Module Manual

Technical Specifications

RF Protocol
Z-Wave
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Z?Wave device type
Z-Wave Switch, Routing Slave
Power
230V?? 10% 50/60 Hz
Operation Range
Up to 20 m indoors with no obstacles
Application
Indoor use only, up to?1.5kW resistive load per circuit
6A per one channel, 9.5A total
Operation temperature
0 ~ 55 ?C
Storage temperature
-10 ~ 80 ?C
Weight
50g
Housing
ABS
Compliance
EN 55015, EN 60669-2-1
Regulatory Compliance Mark
N5496
Dimensions
(LxWxH) 42mm x 37mm x 17mm
The FIBARO Z-Wave RGBW Controller 2 is a one of a kind, advanced wireless 4-colour LED strip controller. Apart from the traditional RGB channels it also supports the white light channel which allows you to add pastel colours to your lighting decorations. The FIBARO Z-Wave RGBW Controller 2 also has four analogue inputs supporting any type of Fibaro sensor (e.g. light sensors, wind sensors, pressure sensors and potentiometers operating between 0-10V). This smart feature allows you to use your lighting as a warning for certain events. You could, for example, set your RGB garden lights to turn red and flicker when one of your security sensors is triggered, alerting your neighbours to the intruder and allowing them to notify the proper authorities. This device has four output channels which means that you can connect and independently control up to four light sources. The FIBARO Z-Wave RGBW Controller 2 also allows you to monitor the energy consumed by the LED strips. Each of the four channels can be monitored independently providing you with all the information you need to minimise your energy bills. The FIBARO Z-Wave RGBW Controller 2 can control:
  • 12 / 24V DC powered RGB strips
  • 12 / 24V DC powered RGBW strips
  • 12 / 24V DC powered LED strips, bulbs, etc
  • 12 / 24V DC powered halogen lights
  • 12 / 24V DC powered low output power fans
Note: Power supply is not included. This product integrates with all Australian certified (921.42 MHz) Z-Wave controllers including:
  • Fibaro Home Center 3/Lite
  • Fibaro Yubii Home

Configuring Z-Wave Devices:

Z-Wave devices often have several configurable parameters which you can change using your Vera?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active for or the type of manual switch connected to a Z-Wave light controller. Every available configurable parameter is listed in your device?s user manual. In most cases your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section. Please check the maximum load before installing or operating. This device must be installed by a certified electrician. For all warranty claims, an electrical compliance certificate from your electrician must be provided.

Technical Specifications

RF Protocol Z?Wave
RF Frequency 921.42Mhz ? AU/NZ ?approved RF for Z?wave
Z?Wave device type Z-Wave dimmer
Power 12V and 24V
Operation Range Up to 50m outdoors, up to 30m indoors (depending on terrain and building structure)
Application Controlled automatically by pre-set Fibaro devices or manually using any Z-Wave controller
Operation temperature 0 ~ 55 ?C
Storage temperature ?10 ~ 80 ?C
Weight 50g
Housing ABS
Compliance EN 55015, EN 60669-2-1
Regulatory Compliance Mark N5496

Documentation

FIBARO Z-Wave RGBW Controller User Manual

Product Details

The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway. The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene. Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk) Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers. FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS

Product Details

The Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene. The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician. This Fibaro Fibaro Z-Wave Double Switch 2 requires 3-wire (including neutral) installation and works with an AC (230V) power supply. The Fibaro Z-Wave Double Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits. This product integrates with Australian certified (921.42 MHz) Z-Wave Controllers - Fibaro Home Center 2/Lite Note: It doesn't integrate with Vera gateways at this stage.

Configuring Z-Wave Devices:

Z-Wave devices often have several configurable parameters which you can change using Fibaro?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller. Every available configurable parameter is listed in your device?s user manual. In most cases, your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. Please check the maximum load before installing or operating. This installation must be done by a certified electrician in Australia and New Zealand. Before engaging an electrician, check that they provide an electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician.

Documentation

Fibaro Z-Wave Double Switch 2 Manual

Technical Specification

RF Protocol
Z-Wave
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Z?Wave device type
Z-Wave Switch, Routing Slave
Power
230V?? 10% 50/60 Hz
Operation Range
Up to 20 m indoors with no obstacles
Application
Indoor use only, up to?1.5kW resistive load per circuit
Operation temperature
0 ~ 55 ?C
Storage temperature
-10 ~ 80 ?C
Weight
50g
Housing
ABS
Compliance
EN 55015, EN 60669-2-1
Regulatory Compliance Mark
N5496
Dimensions
(LxWxH) 42mm x 37mm x 17mm

Product Details

The FIBARO Z-Wave D/W Sensor 2 is a smart magnetic door/window sensor capable of sending binary ON/OFF commands wirelessly using the Z-Wave network (AUS/NZ version 921.42 MHz) when it is triggered. The detector consists of two magnetic units, one is placed on the moving part of the door or window and the other on the frame. The sensor expands the capabilities of your Z-Wave system by monitoring the opening of doors, windows and garage doors. The FIBARO Z-Wave D/W Sensor 2 can be used to automatically turn on lights, turn wireless switches ON/OFF and for security applications within the Z-Wave network. It is also useful for climate control systems, monitoring whether any doors or windows are open to ensure that your air-conditioning is not operating when it is not efficient to do so. This sensor includes a built in temperature sensor which further extends your Z-Wave network's climate control capabilities by allowing it to detect the exact temperature in your home. This product comes in multiple different colours. After all the details are confirmed by the system you will need to go to New service and press Reload Engine after this you will need to wait for the device to reconfigure before it will appear in your system, but once it has it should appear as a D/W sensor in the Vera UI.

Documentation

FIBARO Z-Wave Door/Window Sensor 2 User Manual

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Z?Wave device type
Z-Wave binary sensor, multilevel command supported
Power
One battery, type ER 14250 1/2AA 3.6V (included)
Operation Range
Up to 30m without obstacles
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Temperature Measuring Accuracy
?0.5?C
Temperature Measuring Range
0 ~ 60?C
Weight
70g
Housing
ABS
Dimensions
(LxWxH) 71mm x 18mm x 18mm
Compliance
AS/NZS 4268:2003+A1+A2
Regulatory Compliance Mark ?Z1535
 

Product Description

? Compatible with any Z-Wave network controller, ? May be connected to any alarm system (potential-free output terminal), ? Extremely easy installation - simply put on a surface prone to flooding, ? May be installed anywhere - flood sensor?s contacts extended with a wire, ? Battery or VDC powered. When connected to an external, VDC power source, the battery serves as an emergency power source, ? Theft protection - tilt is reported to the Z-Wave network or alarm system?s main controller, ? Two operating modes - flood/temperature sensor or just a temperature sensor.
Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information