QUBINO Z-Wave Shutter DC

 

$79.99

Availability: In Stock

The QUBINO Z-Wave Tubular Motor Controller DC (by GOAP) is the world’s smallest Z-Wave module able to control 12-24V DC motors of blinds, rollers, shades and Venetian blinds.

  • Z-Wave Plus certified
  • Supports the connection of a temperature sensor
  • Can measure the power consumption of connected device

Discount per quantity

Quantity 4 - 7 8+
Price $75.99 $71.99
% Discount 5% 10%

Buy More for Bigger Savings!

14 in stock

SKU: DHS-WIN-BLW-QUB-DC Categories: , Tags: , ,

Description

The QUBINO Z-Wave Tubular Motor Controller DC is a Z-Wave Plus (500 series) controller for blind, roller and shade motors with 12-24V DC motors. It is designed to fit into an existing switch and enables you to wirelessly control blind motors using a Z-Wave enabled (921.42 MHz in AUS/NZ) controller and reports the motors actual power (Watts) and total power consumption (kWh). This device also supports precise positioning for motors equipped with mechanical or electronic switches.

The QUBINO Z-Wave Tubular Motor Controller DC allows the connection of a temperature sensor that can report the local temperature to your Z-Wave gateway allowing it to better meet your heating/cooling needs.

This product integrates with all Australian certified (921.42 MHz) Z-Wave Controllers including;

Product Support

Technical Specification

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz – AU/NZ  approved RF for Z-wave
Z-Wave device type
Z-Wave binary switch, routing slave
Power
12-24V DC ± 10%
Rated Load Current 
2A
Overcurrent Protection
5A
Output circuit power of DC output (resistive load)
48W (24V DC)
Operation Range
Up to 30m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
10 ~ 40 °C
Storage temperature
-10 ~ 60 °C
Weight
30g
Dimensions
41.8mm x 36.8mm x 16.9mm

Quick Comparison

SettingsQUBINO Z-Wave Shutter DC removeDOME Z-Wave D/W Sensor removeFIBARO ZWave Single Switch 2 removeFIBARO Z-Wave Multi Sensor removeFIBARO Z-Wave Double Switch 2 removeFIBARO Z-Wave RGBW Controller 2 remove
Image
SKUDHS-WIN-BLW-QUB-DCDHS-SNS-DW-DOM-01DHS-LIT-SWW-FIB-012DHS-SNS-MS-FIBDHS-LIT-SWW-FIB-022DHS-LIT-RGBW-FIB
Rating
Price$79.99$43.99$89.99$84.99$89.99$89.99
Stock

14 in stock

1 in stock

13 in stock

13 in stock

20 in stock

19 in stock

Availability14 in stock1 in stock13 in stock13 in stock20 in stock19 in stock
Add to cart

Add to basket

Add to basket

Add to basket

Add to basket

Add to basket

Add to basket

DescriptionThe QUBINO Z-Wave Tubular Motor Controller DC (by GOAP) is the world's smallest Z-Wave module able to control 12-24V DC motors of blinds, rollers, shades and Venetian blinds.
  • Z-Wave Plus certified
  • Supports the connection of a temperature sensor
  • Can measure the power consumption of connected device
Install it on garage doors, closet doors, medicine cabinet doors, and all the windows in your home and get a reminder or sound an alarm when you’ve left anything open. Protect yourself from danger or an invasion of privacy, and find out when someone is snooping around. The Dome Z-Wave D/W Sensor can automate the lights to your doors and windows, and turn them off when you leave the room. Sleek, modern design, and battery operation, means you can install the long-range Dome Z-Wave D/W Sensor anywhere. Use with almost any Z-Wave Hub including Wink, Home Seer, SmartThings, Vera, Harmony and more.The Fibaro Z-Wave Single Switch 2 is a wireless Z-Wave module which can control appliances or lighting up to a maximum load of 2.0kW.
  • Control the ON-OFF function of a circuit remotely or using a wall switch
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling
  • control loads up to 2kW (8A)
The main differences in the FGS-213 are:
  • Z-Wave Plus certification
  • Has power monitoring
  • 230V powered only (this is the same as the FGS-212)
  • No dry contacts - this is important. It means that the new FGS-213 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
The Fibaro Motion Sensor is a universal Z-Wave multi-sensor. Along with detecting motion the device measures the temperature and light intensity. The sensor has a built-in accelerometer to detect any tampering of the device. The Fibaro Motion Sensor is battery powered device and designed to be installed quickly and easily on any surface. The LED indicator signals motion, temperature level, operating mode and can be used to see if the device is within the Z-Wave network. The motion sensor can be used for lighting scenes and security monitoring systems.The new Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave wireless module which can control two circuits each with a maximum load of 6.5A per channel and 10A total load per circuit.
  • Control the ON-OFF function of two two independent circuits or appliances remotely or using a wall switch
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling
  • Latest generation Z-Wave 500 series chip
  • Z-Wave Plus certification
  • Very accurate energy measurement +/- 1 % for power above 5W
  • Supports secure mode (Z-Wave Network Security) encrypted with AES-128
  • No dry contacts - this is important. It means that the new FGS-223 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls.
The FIBARO Z-Wave RGBW Controller 2 is a wireless controller which enables you to manage your LED strips and halogen lights.
  • Wirelessly control LEDs with an unlimited range of colour options
  • Monitors energy usage
  • Four analogue sensor inputs
  • Four dimmer channels
  • Acts as a repeater expanding your Z-Wave network
ContentThe QUBINO Z-Wave Tubular Motor Controller DC is a Z-Wave Plus (500 series) controller for blind, roller and shade motors with 12-24V DC motors. It is designed to fit into an existing switch and enables you to wirelessly control blind motors using a Z-Wave enabled (921.42 MHz in AUS/NZ) controller and reports the motors actual power (Watts) and total power consumption (kWh). This device also supports precise positioning for motors equipped with mechanical or electronic switches. The QUBINO Z-Wave Tubular Motor Controller DC allows the connection of a temperature sensor that can report the local temperature to your Z-Wave gateway allowing it to better meet your heating/cooling needs. This product integrates with all Australian certified (921.42 MHz) Z-Wave Controllers including;

Product Support

Technical Specification

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z-Wave device type
Z-Wave binary switch, routing slave
Power
12-24V DC ± 10%
Rated Load Current 
2A
Overcurrent Protection
5A
Output circuit power of DC output (resistive load)
48W (24V DC)
Operation Range
Up to 30m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
10 ~ 40 °C
Storage temperature
-10 ~ 60 °C
Weight
30g
Dimensions
41.8mm x 36.8mm x 16.9mm
The DOME Z-Wave D/W Sensor is a Z-Wave Plus (500 series) compatible, battery-powered sensor designed for security and lighting automation applications. This sensor can be configured to alert you when it detects a motion and/or to trigger a siren in your Z-Wave network to scare off an intruder. Meanwhile, the built-in ambient light sensor allows this device to not only turn on your lights when you enter a room but also to automatically dim them to an appropriate level. This product is compatible with all Australian certified (921.42MHz) Z-Wave and Z-Wave Plus controllers including:

Product Support

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z-Wave device type
Z-Wave Binary sensor
Power
1 x CR123 3.0V battery (included)
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
5 ~ 40 °C
Storage temperature
-10 ~ 50 °C
Weight
50g
Dimensions
65mm
Housing
ABS

Product Details

The Fibaro Z-Wave Single Switch 2 is a smart Z-Wave module capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene. The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician. This Fibaro Z-Wave Single Switch 2 requires 3-wire (including neutral) installation and works with an AC (110-230V) or DC (24-60V) power supply. The Fibaro Z-Wave Single Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits. This product integrates with all Australian certified (921.42MHz) Z-Wave controllers including:
  • Raspberry PI with RaZberry Card
  • Fibaro Home Controller 2/Lite
  • DHS Z-Wave Universal Remote Controller
  • DHS Z-Wave Mini Remote Controller

Configuring Z-Wave Devices

Z-Wave devices often have several configurable parameters which you can change using your Vera’s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller. Every available configurable parameter is listed in your device’s user manual. In most cases, your device’s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section. Please check the maximum load before installing or operating. This installation must be done by a certified electrician in Australia and New Zealand. Before engaging an electrician, check that they provide an electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician.  

Technical Specifications

RF Protocol Z-Wave
RF Frequency 921.42Mhz - AU/NZ  approved RF for Z‐wave
Z‐Wave device type Z-Wave Switch, Routing Slave
Power 110-230V ± 10% 50/60 Hz
Operation Range Up to 20m indoors with no obstacles
Weight 50g
Housing ABS
Compliance EN 55015, EN 60669-2-1
Regulatory Compliance Mark N5496
Dimensions (LxWxH) 42mm x 37mm x 17mm
 

Wiring Diagram

 

 

Documentation

Fibaro Z-Wave Single Switch 2 Manual (Size: 724 Kb) Configuring_ZWave_Device_Parameters_in_VeraUI7

Product Details

  • Compatible with any Z-Wave controller.
  • Detects motion using a passive IR sensor.
  • Measures the temperature.
  • Measures the light intensity.
  • Easy installation on a wall or any surface.
  • Protected against tampering and theft - once vibrations are detected, the notification is sent to the main controller.
  • Alarms of movement and temperature are signalled by LED diode blinking.
  • Simple earthquake detector mode.

Technical Specifications

Product Name 
FIBARO MOTION SENSOR FGMS-001 V2.4
Battery Type
CR123A battery, 3.6 VDC
Operation Range
30m
Light Intensity Measuring Range:
0-32000 LUX
Radio frequency
921.42 MHz (AU/NZ Z-Wave)
Power Consumption
0,4W
Operation temperature
0 - 50C*
Measured temperature range -20 to 100C
Temperature measuring accuracy
0,5 C
Housing
ABS
Size (Diameter)
44 mm
       

Product Details

The Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene. The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician. This Fibaro Fibaro Z-Wave Double Switch 2 requires 3-wire (including neutral) installation and works with an AC (230V) power supply. The Fibaro Z-Wave Double Switch 2 also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits. This product integrates with Australian certified (921.42 MHz) Z-Wave Controllers - Fibaro Home Center 2/Lite Note: It doesn't integrate with Vera gateways at this stage.

Configuring Z-Wave Devices:

Z-Wave devices often have several configurable parameters which you can change using Fibaro’s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active or the type of manual switch connected to a Z-Wave light controller. Every available configurable parameter is listed in your device’s user manual. In most cases, your device’s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. Please check the maximum load before installing or operating. This installation must be done by a certified electrician in Australia and New Zealand. Before engaging an electrician, check that they provide an electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician.

Documentation

Fibaro Z-Wave Double Switch 2 Manual

Technical Specification

RF Protocol
Z-Wave
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z‐Wave device type
Z-Wave Switch, Routing Slave
Power
230V ± 10% 50/60 Hz
Operation Range
Up to 20 m indoors with no obstacles
Application
Indoor use only, up to 1.5kW resistive load per circuit
Operation temperature
0 ~ 55 °C
Storage temperature
-10 ~ 80 °C
Weight
50g
Housing
ABS
Compliance
EN 55015, EN 60669-2-1
Regulatory Compliance Mark
N5496
Dimensions
(LxWxH) 42mm x 37mm x 17mm
The FIBARO Z-Wave RGBW Controller 2 is a one of a kind, advanced wireless 4-colour LED strip controller. Apart from the traditional RGB channels it also supports the white light channel which allows you to add pastel colours to your lighting decorations. The FIBARO Z-Wave RGBW Controller 2 also has four analogue inputs supporting any type of Fibaro sensor (e.g. light sensors, wind sensors, pressure sensors and potentiometers operating between 0-10V). This smart feature allows you to use your lighting as a warning for certain events. You could, for example, set your RGB garden lights to turn red and flicker when one of your security sensors is triggered, alerting your neighbours to the intruder and allowing them to notify the proper authorities. This device has four output channels which means that you can connect and independently control up to four light sources. The FIBARO Z-Wave RGBW Controller 2 also allows you to monitor the energy consumed by the LED strips. Each of the four channels can be monitored independently providing you with all the information you need to minimise your energy bills. The FIBARO Z-Wave RGBW Controller 2 can control:
  • 12 / 24V DC powered RGB strips
  • 12 / 24V DC powered RGBW strips
  • 12 / 24V DC powered LED strips, bulbs, etc
  • 12 / 24V DC powered halogen lights
  • 12 / 24V DC powered low output power fans
Note: Power supply is not included. This product integrates with all Australian certified (921.42 MHz) Z-Wave controllers including:
  • Fibaro Home Center 3/Lite
  • Fibaro Yubii Home

Configuring Z-Wave Devices:

Z-Wave devices often have several configurable parameters which you can change using your Vera’s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active for or the type of manual switch connected to a Z-Wave light controller. Every available configurable parameter is listed in your device’s user manual. In most cases your device’s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section. Please check the maximum load before installing or operating. This device must be installed by a certified electrician. For all warranty claims, an electrical compliance certificate from your electrician must be provided.

Technical Specifications

RF Protocol Z‐Wave
RF Frequency 921.42Mhz ‐ AU/NZ  approved RF for Z‐wave
Z‐Wave device type Z-Wave dimmer
Power 12V and 24V
Operation Range Up to 50m outdoors, up to 30m indoors (depending on terrain and building structure)
Application Controlled automatically by pre-set Fibaro devices or manually using any Z-Wave controller
Operation temperature 0 ~ 55 °C
Storage temperature ‐10 ~ 80 °C
Weight 50g
Housing ABS
Compliance EN 55015, EN 60669-2-1
Regulatory Compliance Mark N5496

Documentation

FIBARO Z-Wave RGBW Controller User Manual
Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information