QUBINO Z-Wave Shutter

 

$88.99

Availability: In Stock

The QUBINO Z-Wave Tubular Motor Controller (by GOAP) is the world’s smallest Z-Wave module able to control the motors of blinds, rollers, shades and Venetian blinds.

  • Z-Wave Plus certified
  • Supports the connection of a temperature sensor
  • Requires 3-wire (including neutral) installation
  • Can measure the power consumption of connected device

Discount per quantity

Quantity 4 - 7 8+
Price $84.54 $80.09
% Discount 5% 10%

Buy More for Bigger Savings!

20 in stock

SKU: DHS-WIN-BLW-QUB Categories: , Tags: , ,

Description

The QUBINO Z-Wave Tubular Motor Controller is a Z-Wave Plus (500 series) controller for blind, roller and shade motors. It is designed to fit into an existing switch and enables you to wirelessly control blind motors using a Z-Wave enabled (921.42 MHz in AUS/NZ) controller and reports the motors actual power (Watts) and total power consumption (kWh). This device also supports precise positioning for motors equipped with mechanical or electronic switches.

The QUBINO Z-Wave Tubular Motor Controller allows the connection of a temperature sensor that can report the local temperature to your Z-Wave gateway allowing it to better meet your heating/cooling needs.

This product integrates with all Australian certified (921.42 MHz) Z-Wave Controllers including;

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz – AU/NZ  approved RF for Z-wave
Z-Wave device type
Z-Wave binary switch, routing slave
Power
230 VAC ± 10%
Load
2 x 920W (4A resistive @ 230V AC)
Power Consumption
< 0.7W
Operation Range
Up to 30m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
10 ~ 40 °C
Storage temperature
-10 ~ 60 °C
Weight
30g
Dimensions
41.8mm x 36.8mm x 16.9mm

Quick Comparison

SettingsQUBINO Z-Wave Shutter removeAEOTEC Range Extender removeFIBARO Z-Wave Dimmer 2 removeFIBARO Z-Wave RGBW Controller 2 removeFIBARO Z-Wave Swipe Pad White removeFIBARO Z-Wave Implant remove
Image
SKUDHS-WIN-BLW-QUBDHS-CON-REXT-AEODHS-LIT-DMW-FIB-02DHS-LIT-RGBW-FIBDHS-CON-SCON-FIBDHS-SNS-IMP-FIB
Rating
Price$88.99$68.99$98.99$89.99$219.99$71.99
Stock

20 in stock

1 in stock

20 in stock

19 in stock

Out of stock

14 in stock

Availability20 in stock1 in stock20 in stock19 in stockOut of stock14 in stock
Add to cart

Add to basket

Add to basket

Add to basket

Add to basket

Read more

Add to basket

DescriptionThe QUBINO Z-Wave Tubular Motor Controller (by GOAP) is the world's smallest Z-Wave module able to control the motors of blinds, rollers, shades and Venetian blinds.
  • Z-Wave Plus certified
  • Supports the connection of a temperature sensor
  • Requires 3-wire (including neutral) installation
  • Can measure the power consumption of connected device
Range Extender 6. The Range Extender 6 keeps it reliable. We all know how annoying weak wireless signals can be. Weak WiFi and poor phone signals are frustrating. Imagine if your smart home was also plagued by weak wireless signals and the same frustrations? Your smart home would not be very smart. The Range Extender 6 from Aeotec ensures that your connected home stays connected. It intelligently listens to the commands and reports that your Z-Wave network sends, actively capturing weak signals and then amplifying and repeating them. ZW117cThe Fibaro Z-Wave In-Wall Dimmer 2 (FGD-212) is the newest version of a popular wireless controller designed to operate behind a wall switch.
  • Control the level of illumination of your light remotely or using a manual button (in two and three way configurations)
  • Implemented algorithm of smart light source detection
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive re-wiring
  • Active power and energy metering functionality
  • Works with various types of manual buttons
  • Active element: semiconductor electronic switch
The FIBARO Z-Wave RGBW Controller 2 is a wireless controller which enables you to manage your LED strips and halogen lights.
  • Wirelessly control LEDs with an unlimited range of colour options
  • Monitors energy usage
  • Four analogue sensor inputs
  • Four dimmer channels
  • Acts as a repeater expanding your Z-Wave network
FIBARO Swipe is a wireless, battery powered gesture-controlled pad that allows you to activate Z-Wave scenes or commands with a simple wave of the hand. FIBARO Swipe has the appearance of a small tablet but instead of a touchscreen, it uses sophisticated motion identification technology to respond to six distinct hand gestures including four directional swipes (up, down, left, right), and two circular motions (left, right). A single gesture or a combination of gestures may be used – for example, swipe “down” to turn off the lights, “up” to open your blinds. With four short swipes, the living room is transformed into a home theater! Swipe’s only limit is your imagination.
  • Z-Wave Plus certified contactless gesture control
  • May be used with wet or dirty hands – e.g. turn on the lights in the kitchen or bathroom without getting the switches or wall dirty
  • Endless control possibilities – e.g. wave goodbye to activate your “going out” scene, swipe up to raise the volume on your sound system, swipe down to close difficult to reach skylight windows, reach out your hand from bed in the morning to activate your coffee machine
  • Endless placement possibilities – e.g. visible on the dresser or a wall with your favourite family photos, or hidden away under the kitchen counter or coffee table
  • Powered by 4xAA batteries or Micro-USB giving you ultimate flexibility
  • Available in black or white
FIBARO Smart Implant allows to enhance the functionality of wired sensors and other devices by adding Z-Wave network communication. You can connect binary sensors, analog sensors, DS18B20 temperature sensors or DHT22 humidity and temperature sensor to report their readings to the Z-Wave controller. It can also control devices by opening/closing output contacts independently of the inputs.
ContentThe QUBINO Z-Wave Tubular Motor Controller is a Z-Wave Plus (500 series) controller for blind, roller and shade motors. It is designed to fit into an existing switch and enables you to wirelessly control blind motors using a Z-Wave enabled (921.42 MHz in AUS/NZ) controller and reports the motors actual power (Watts) and total power consumption (kWh). This device also supports precise positioning for motors equipped with mechanical or electronic switches. The QUBINO Z-Wave Tubular Motor Controller allows the connection of a temperature sensor that can report the local temperature to your Z-Wave gateway allowing it to better meet your heating/cooling needs. This product integrates with all Australian certified (921.42 MHz) Z-Wave Controllers including;

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z-Wave device type
Z-Wave binary switch, routing slave
Power
230 VAC ± 10%
Load
2 x 920W (4A resistive @ 230V AC)
Power Consumption
< 0.7W
Operation Range
Up to 30m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
10 ~ 40 °C
Storage temperature
-10 ~ 60 °C
Weight
30g
Dimensions
41.8mm x 36.8mm x 16.9mm

Product Description

Repeats wireless signals. Repeats wireless signals.For your smart home to be perfect, its wireless signals need to be reliable. Range Extender 6 captures weak or slow signals and efficiently repeats them on to the rest of your Z-Wave network. Amplifies wireless signals. Amplifies wireless signals.Not only does Range Extender 6 accurately repeat Z-Wave signals, it amplifies them too and helps improve the reliability and accuracy of your Z-Wave network. Big on impact. Small in size. Range Extender 6 is a power-outlet friendly device, designed to be as small and as compact as possible without compromising on performance. so that it doesn’t block neighbouring power outlets.

Product Support

Works with VeraAeotec LED Bulb with Vera Manuals: ⇒  Aeotec Range Extender 6 product manuals

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z-Wave device type
Amplifier
Power
240V AC
Operation Range
Up to 150m without obstacles
Application
Indoor use only
Operation temperature
0 ~ 55 °C
Storage temperature
-10 ~ 80 °C
Colour
white
Weight
50g
Housing
ABS
Size
43mm x 40mm x 16mm
Compliance
Z-Wave Plus certified
Warranty 12 Months
The Fibaro Z-Wave In-Wall Dimmer 2 is designed to operate with or without a neutral wire. It may be used as a switch in systems without a neutral wire. In the case of a 2-wire connection (no neutral), the Fibaro Z-Wave In-Wall Dimmer 2 may require a minimum load of 50W depending on the specifics of the connected load. When used with a Fibaro Dimmer Bypass 2 it may operate with any compatible (see below) load from 5W. Before committing to buy Fibaro Dimmer Bypass 2 please check if your load can be properly controlled by Fibaro Dimmer 2 without a bypass device. Do not connect this device to a power supply without a load. Only lighting devices may be connected to this device. As a dimmer it operates with the following loads:
  • 230V operated conventional incandescent (from 50W to 250W)
  • 230V operated halogen (from 50W to 200W)
  • 12 V operated ELV halogen lamps and dimmable LED lamps (with electronic transformers: Trailing and Leading-edge type) (from 50W to 200W)
  • 12V operated MLV halogen lamps (with ferromagnetic transformers) (from 50W to 225W)
  • Dimmable CFL tube lamps with electronic ballast only (from 50W to 200W)
As a switch it operates with the following loads:
  • Compact fluorescent lamps with electronic ballast
  • LED bulbs (power factor >0.7)
  • Fluorescent tube lamps with electronic ballast
Please note: For loads other than resistive do not exceed a 1.5A current. This product integrates with all Australian certified (921.42 MHz) Z-Wave and Z-Wave Plus controllers including:
  • Vera Plus/ Edge
  • Fibaro Home Center 2 / Lite
Please note: Do not mix the load type (e.g. LED and CFL or different types of transformers) as it will impede the proper operation of the dimmer. Doing so will void the dimmer's warranty. This product must be installed by a qualified electrician. Before engaging an electrician, check that they provide a warranty and electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician. PLEASE NOTE FOR THE INSTALLATIONS IN THE AREAS WHERE ELECTRICITY SUPPLIERS USE OFF-PEAK RIPPLE CONTROL SIGNALS: Electricity suppliers in particular areas of Australia such as NSW, QLD and some other places are injecting an off-peak ripple control signal using Zellweger equipment or similar onto their distribution networks in order to remotely control devices such as off-peak hot water systems and street lighting, although other areas within Australia also use this technology. Not all properties are affected by ripple control, so just because you might live in one of these areas, does not mean that you will have these problems. Ripple injection control systems work by superimposing coded control signals, commonly 750Hz or 1050Hz on the 50 Hz mains supply. Some electrical appliances such as fans, dimmers, toasters and LED lighting can be sensitive to this ripple control signal. The results could be audible buzzing noises from fans or flickering lights whenever the ripple control signals are present. Electricity suppliers are advising users to install appropriate ripple signal filters in such areas. The ripple signal filter is a tuned passive inline filter that completely eliminates the superimposed ripple injection control signal from the normal mains supply to produce a noise free filtered mains supply which can then be connected to the electrical appliances or light control systems. The ripple signal filter is specifically tuned to eliminate the ripple control signal frequency of 750Hz or 1050Hz. However, we can’t guarantee the ripple signal filter always will help you if you experiencing such issues. Please contact your local energy provider to get more information and proposed solutions for your electrical installation. If you are getting similar problems with your dimmers and fans and it’s not Ripple Control Signal and you are hearing the tones at random times of the day, your electrical supply may be affected by harmonics; a power fluctuation that is not part of the normal electricity supply or ripple control signal output. Harmonics are caused by interference created by other equipment on the network, such as inverter type air conditioners and switch mode power supplies for computers. The offending appliances may be in your home or other premises on the local power grid. If you are being affected by network harmonics, it may be of benefit to transfer the electricity supply to your premises to a different phase in the street. This is something you will need to discuss with your electrical company. We are strongly recommending for the areas we have mentioned above to run tests with only a few dimmers before committing for high volumes. If results are not fully OK you may use relays only instead of dimmers. Please note that our warranty for the faulty devices is not covering above mentioned conditions with your local electric grids. Please see affected with Ripple Signalling areas here:

QUEENSLAND

  • Only Southern Queensland (Energex) has Ripple Signalling.
  • The Frequency is 1050Hz.
  • The rest of Queensland (Ergon) does not have Ripple Signalling.

NSW

  • Energy Australia Full Supply Area
  • Energy Australia Sydney &Hunter Supply Area

Documentation

Fibaro Z-Wave In-Wall Dimmer 2 Manual

Technical Specifications

RF Protocol
Z-Wave
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z‐wave device type
Z-Wave multiple level dimmer, routing slave
Power Supply
220 - 240V ~ 50Hz
Operation Range
Up to 30m indoors (depending on building materials)
Application
Indoor use only
Operation temperature
0 ~ 35 °C
Dimensions (L x W x H)
42.5mm x 38.25mm x 20.3mm
Weight
30g
Operational Current
0.25 - 1.1A
Compliance
RCM E3606
Dimming type compatibility
Leading and Trailing Edge
The FIBARO Z-Wave RGBW Controller 2 is a one of a kind, advanced wireless 4-colour LED strip controller. Apart from the traditional RGB channels it also supports the white light channel which allows you to add pastel colours to your lighting decorations. The FIBARO Z-Wave RGBW Controller 2 also has four analogue inputs supporting any type of Fibaro sensor (e.g. light sensors, wind sensors, pressure sensors and potentiometers operating between 0-10V). This smart feature allows you to use your lighting as a warning for certain events. You could, for example, set your RGB garden lights to turn red and flicker when one of your security sensors is triggered, alerting your neighbours to the intruder and allowing them to notify the proper authorities. This device has four output channels which means that you can connect and independently control up to four light sources. The FIBARO Z-Wave RGBW Controller 2 also allows you to monitor the energy consumed by the LED strips. Each of the four channels can be monitored independently providing you with all the information you need to minimise your energy bills. The FIBARO Z-Wave RGBW Controller 2 can control:
  • 12 / 24V DC powered RGB strips
  • 12 / 24V DC powered RGBW strips
  • 12 / 24V DC powered LED strips, bulbs, etc
  • 12 / 24V DC powered halogen lights
  • 12 / 24V DC powered low output power fans
Note: Power supply is not included. This product integrates with all Australian certified (921.42 MHz) Z-Wave controllers including:
  • Fibaro Home Center 3/Lite
  • Fibaro Yubii Home

Configuring Z-Wave Devices:

Z-Wave devices often have several configurable parameters which you can change using your Vera’s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active for or the type of manual switch connected to a Z-Wave light controller. Every available configurable parameter is listed in your device’s user manual. In most cases your device’s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section. Please check the maximum load before installing or operating. This device must be installed by a certified electrician. For all warranty claims, an electrical compliance certificate from your electrician must be provided.

Technical Specifications

RF Protocol Z‐Wave
RF Frequency 921.42Mhz ‐ AU/NZ  approved RF for Z‐wave
Z‐Wave device type Z-Wave dimmer
Power 12V and 24V
Operation Range Up to 50m outdoors, up to 30m indoors (depending on terrain and building structure)
Application Controlled automatically by pre-set Fibaro devices or manually using any Z-Wave controller
Operation temperature 0 ~ 55 °C
Storage temperature ‐10 ~ 80 °C
Weight 50g
Housing ABS
Compliance EN 55015, EN 60669-2-1
Regulatory Compliance Mark N5496

Documentation

FIBARO Z-Wave RGBW Controller User Manual

Product Details

The FIBARO Swipe is equipped with the most precise 3D motion detecting sensor of its kind, which ensures flawless recognition of the performed gestures. It presents a new and innovative way of controlling home automation devices in an intuitive and user friendly way. The magic of Swipe means you can position it in less conventional places as it will work through solid surfaces, like under a desk or behind a wall. And when displayed, Swipe can be used as a beautifully designed picture frame allowing you to easily change photos whenever you want through a simple to remove front panel. A special gesture controlled menu also allows you to add/remove or reset the device without dismantling it. With the endless possibilities of a gesture, Swipe is a perfect solution for the elderly and disabled, or people who find technology difficult to learn. Show them how to turn on the heating or ventilate the room without even getting up from the chair. Swipe needn’t be limited to the home either. Use it in the workplace to help you make the office as comfortable as the home. Control blinds, lights or a projector – all with a wave of your hand. FIBARO Swipe features the latest Z-Wave 500 series chip for improved wireless range, security and data transfer rates. Please note: Currently integrates with Australian Z-Wave certified (921.42MHz) Fibaro Home Center 2/Lite controllers only.

Installation

  • Place the Swipe onto its holder.
  • Place the Swipe within the direct range of your Z-Wave controller.
  • Plug the power source into the micro-USB port if required.
  • Set the main controller in (security/non-security) add mode (see the controller’s manual).
  • Move and hold your hand close to the center of the pad.
  • If the device is battery powered, high pitched beep will signal exiting the Standby Mode.
  • Loud sound sequence will confirm entering the menu, keep holding your hand.
  • After hearing two short beeps (green indicator colour), withdraw the hand and perform swiping up gesture to confirm selection (two beeps will confirm validity).
  • Wait for the adding process to end.
  • Successful adding will be confirmed by the Z-Wave controller’s message and 3 short beeps (green visual indicator colour).

Technical Specifications

RF Protocol Z-Wave Plus™
RF Frequency 921.42Mhz ‐ AU/NZ  approved RF for Z‐wave
Application Indoor use only
Power 4xAA Batteries or 5V DC Power Supply: Micro-USB
Operation Range Up to 30m indoors with no obstacles
Enclosure White or Black
Compliance EMC 2004/108/EC
R&TTE 1999/5/EC
RoHS 2011/65/EU
LVD 2006/95/EC
DC supply connector Micro-USB
Dimensions (LxWxH) 178 x 130 x 29 mm
 

Documentation

FIBARO Z-Wave SWIPE Manual FIBARO Swipe - Home Automation Gesture Control Pad

Product Description

Supports Z-Wave network Security Modes: S0 with AES-128 encryption and S2 Authenticated with PRNG-based encryption. Works as a Z-Wave signal repeater. Allows for connecting sensors: 6 DS18B20 sensors, 1 DHT sensor, 2 2-wire analog sensor, 2 3-wire analog sensor, 2 binary sensors. Built-in temperature sensor. This product works with : Fibaro Home Controller 3/2/Lite Please note: THE DEVICE IS NOT COMPATIBLE WITH VERA HOME CONTROLLERS Before installation Connect only in accordance with one of the diagrams, The device is powered with secure voltage; nevertheless, the user should be extra careful or should commission the installation to a qualified person, Do not connect devices that are not compliant with the specification, Do not connect other sensors than DS18B20 or DHT22 to SP and SD terminals, Do not connect sensors to SP and SD terminals with wires longer than 3 meters, Do not load the device outputs with a current exceeding 150mA, Every connected device should be compliant with the relevant safety standards, Unused lines should be left insulated. Tips for arranging the antenna: Locate the antenna as far from metal elements as possible (connecting wires, bracket rings, etc.) in order to prevent interferences, Metal surfaces in the direct vicinity of the antenna (e.g. flush mounted metal boxes, metal door frames) may impair signal reception! Do not cut or shorten the antenna – its length is perfectly matched to the band in which the system operates. Make sure no part of the antenna sticks out of the wall switch box.
Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information