FIBARO CO SENSOR HOMEKIT

 

$144.99

Availability: In Stock

FIBARO CO Sensor is a HomeKit-enabled carbon monoxide detector using Bluetooth® low energy wireless technology.
Its high sensitivity allows detecting the presence of the carbon monoxide (CO) gas at the early stage in order to prevent carbon monoxide poisoning.
An alarm is signalled with a built-in siren, blinking LED indicator and sending information to your iOS device.

25 in stock

Description

FIBARO CO Sensor is a HomeKit-enabled carbon monoxide detector using Bluetooth® low energy wireless technology.
Its high sensitivity allows detecting the presence of the carbon monoxide (CO) gas at the early stage in order to prevent carbon monoxide poisoning.
An alarm is signalled with a built-in siren, blinking LED indicator and sending information to your iOS device.

Quick Comparison

SettingsFIBARO CO SENSOR HOMEKIT removeFIBARO Z-Wave Button (Yellow) removeFIBARO Z-Wave Button (Black) removeFIBARO Z-Wave Dimmer 2 removeFIBARO Home Center 3 Lite removeFIBARO Z-Wave KeyFob remove
Image
SKUFGBHCD-001DHS-CON-SBUT-FIB-YLDHS-CON-SBUT-FIB-BLDHS-LIT-DMW-FIB-02DHS-CON-HC3LITE-FIBDHS-CON-KFB-FIB
Rating
Price$144.99$79.99$79.99$98.99$219.99$79.99
Stock

25 in stock

2 in stock

1 in stock

20 in stock

20 in stock

2 in stock

Availability25 in stock2 in stock1 in stock20 in stock20 in stock2 in stock
Add to cart

Add to basket

Add to basket

Add to basket

Add to basket

Add to basket

Add to basket

DescriptionFIBARO CO Sensor is a HomeKit-enabled carbon monoxide detector using Bluetooth® low energy wireless technology. Its high sensitivity allows detecting the presence of the carbon monoxide (CO) gas at the early stage in order to prevent carbon monoxide poisoning. An alarm is signalled with a built-in siren, blinking LED indicator and sending information to your iOS device.The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
  • Completely wireless
  • Z-Wave Plus certified
  • Supports 6 different actions/scenes
  • Available in multiple colours (white, black, red, blue, yellow)
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
  • Completely wireless
  • Z-Wave Plus certified
  • Supports 6 different actions/scenes
  • Available in multiple colours (white, black, red, blue, yellow)
The Fibaro Z-Wave In-Wall Dimmer 2 (FGD-212) is the newest version of a popular wireless controller designed to operate behind a wall switch.
  • Control the level of illumination of your light remotely or using a manual button (in two and three way configurations)
  • Implemented algorithm of smart light source detection
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive re-wiring
  • Active power and energy metering functionality
  • Works with various types of manual buttons
  • Active element: semiconductor electronic switch
This new Fibaro home controller offers impressive hardware and integration options for installers and clients. This excellent Smart Home controller offers next generation hardware, including: COMMUNICATION TECHNOLOGY: Z-WAVE (700 series) NETWORK TECHNOLOGY: Wi-Fi 2.4GHz CPU: Single-Core ARM Cortex A7 900 MHz RAM MEMORY: 512 MB FLASH MEMORY: 4 GB eMMC The Fibaro Home Center 3 Lite is the perfect controller for small Home Automation projects, offering an excellent solution for smaller homes or apartments. The system is recommended for Smart Homes with up to 40 Z-Wave devices and 20 scenes. But, don't be mistaken by its size, the Fibaro HC3 Lite offers an affordable solution without having to compromise on quality. With this new system, you'll be able to automate a variety of solutions, including: Fibaro HC3 Lite SolutionsThe FIBARO Keyfob is a battery powered, compact remote controller that allows you to control devices in your Z-Wave network.
  • Supports 30 different actions
  • Z-Wave Plus certified
  • Fully configurable, automatic pin lock prevents unauthorised use
  • Supports protected mode (Z-Wave network security mode) with AES-128 encryption
ContentFIBARO CO Sensor is a HomeKit-enabled carbon monoxide detector using Bluetooth® low energy wireless technology. Its high sensitivity allows detecting the presence of the carbon monoxide (CO) gas at the early stage in order to prevent carbon monoxide poisoning. An alarm is signalled with a built-in siren, blinking LED indicator and sending information to your iOS device.

Product Details

The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway. The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene. Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk) Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers. FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Power
ER14250 ½ AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 °C
Storage temperature
‐10 ~ 50 °C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS

Product Details

The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway. The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene. Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk) Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers. FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Power
ER14250 ½ AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 °C
Storage temperature
‐10 ~ 50 °C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS
The Fibaro Z-Wave In-Wall Dimmer 2 is designed to operate with or without a neutral wire. It may be used as a switch in systems without a neutral wire. In the case of a 2-wire connection (no neutral), the Fibaro Z-Wave In-Wall Dimmer 2 may require a minimum load of 50W depending on the specifics of the connected load. When used with a Fibaro Dimmer Bypass 2 it may operate with any compatible (see below) load from 5W. Before committing to buy Fibaro Dimmer Bypass 2 please check if your load can be properly controlled by Fibaro Dimmer 2 without a bypass device. Do not connect this device to a power supply without a load. Only lighting devices may be connected to this device. As a dimmer it operates with the following loads:
  • 230V operated conventional incandescent (from 50W to 250W)
  • 230V operated halogen (from 50W to 200W)
  • 12 V operated ELV halogen lamps and dimmable LED lamps (with electronic transformers: Trailing and Leading-edge type) (from 50W to 200W)
  • 12V operated MLV halogen lamps (with ferromagnetic transformers) (from 50W to 225W)
  • Dimmable CFL tube lamps with electronic ballast only (from 50W to 200W)
As a switch it operates with the following loads:
  • Compact fluorescent lamps with electronic ballast
  • LED bulbs (power factor >0.7)
  • Fluorescent tube lamps with electronic ballast
Please note: For loads other than resistive do not exceed a 1.5A current. This product integrates with all Australian certified (921.42 MHz) Z-Wave and Z-Wave Plus controllers including:
  • Vera Plus/ Edge
  • Fibaro Home Center 2 / Lite
Please note: Do not mix the load type (e.g. LED and CFL or different types of transformers) as it will impede the proper operation of the dimmer. Doing so will void the dimmer's warranty. This product must be installed by a qualified electrician. Before engaging an electrician, check that they provide a warranty and electrical compliance certificate. For a warranty claim, you have to provide an installation compliance certificate from your electrician. PLEASE NOTE FOR THE INSTALLATIONS IN THE AREAS WHERE ELECTRICITY SUPPLIERS USE OFF-PEAK RIPPLE CONTROL SIGNALS: Electricity suppliers in particular areas of Australia such as NSW, QLD and some other places are injecting an off-peak ripple control signal using Zellweger equipment or similar onto their distribution networks in order to remotely control devices such as off-peak hot water systems and street lighting, although other areas within Australia also use this technology. Not all properties are affected by ripple control, so just because you might live in one of these areas, does not mean that you will have these problems. Ripple injection control systems work by superimposing coded control signals, commonly 750Hz or 1050Hz on the 50 Hz mains supply. Some electrical appliances such as fans, dimmers, toasters and LED lighting can be sensitive to this ripple control signal. The results could be audible buzzing noises from fans or flickering lights whenever the ripple control signals are present. Electricity suppliers are advising users to install appropriate ripple signal filters in such areas. The ripple signal filter is a tuned passive inline filter that completely eliminates the superimposed ripple injection control signal from the normal mains supply to produce a noise free filtered mains supply which can then be connected to the electrical appliances or light control systems. The ripple signal filter is specifically tuned to eliminate the ripple control signal frequency of 750Hz or 1050Hz. However, we can’t guarantee the ripple signal filter always will help you if you experiencing such issues. Please contact your local energy provider to get more information and proposed solutions for your electrical installation. If you are getting similar problems with your dimmers and fans and it’s not Ripple Control Signal and you are hearing the tones at random times of the day, your electrical supply may be affected by harmonics; a power fluctuation that is not part of the normal electricity supply or ripple control signal output. Harmonics are caused by interference created by other equipment on the network, such as inverter type air conditioners and switch mode power supplies for computers. The offending appliances may be in your home or other premises on the local power grid. If you are being affected by network harmonics, it may be of benefit to transfer the electricity supply to your premises to a different phase in the street. This is something you will need to discuss with your electrical company. We are strongly recommending for the areas we have mentioned above to run tests with only a few dimmers before committing for high volumes. If results are not fully OK you may use relays only instead of dimmers. Please note that our warranty for the faulty devices is not covering above mentioned conditions with your local electric grids. Please see affected with Ripple Signalling areas here:

QUEENSLAND

  • Only Southern Queensland (Energex) has Ripple Signalling.
  • The Frequency is 1050Hz.
  • The rest of Queensland (Ergon) does not have Ripple Signalling.

NSW

  • Energy Australia Full Supply Area
  • Energy Australia Sydney &Hunter Supply Area

Documentation

Fibaro Z-Wave In-Wall Dimmer 2 Manual

Technical Specifications

RF Protocol
Z-Wave
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z‐wave device type
Z-Wave multiple level dimmer, routing slave
Power Supply
220 - 240V ~ 50Hz
Operation Range
Up to 30m indoors (depending on building materials)
Application
Indoor use only
Operation temperature
0 ~ 35 °C
Dimensions (L x W x H)
42.5mm x 38.25mm x 20.3mm
Weight
30g
Operational Current
0.25 - 1.1A
Compliance
RCM E3606
Dimming type compatibility
Leading and Trailing Edge
Security: The FIBARO System will ensure the safety of you and your loved ones.
  • Smoke detection
  • Carbon monoxide detection
  • Flood detection
  • Operation as a wireless alarm system
  • Cooperation with the existing wired alarm system (eg SATEL) and security companies
  • Emergency door opening
  • Closing the roller shutters when you are away
Health: The FIBARO System will help you ensure the right conditions for your health.
  • Humidity control
  • Smart heating
  • Measurement of air quality and quality of PM2.5 and PM10 dust
  • Detection of hazardous gases
  • Control of ventilation and recuperation
  • Notifications in case of dangerous situations
Convenience: An intelligent home is primarily about increasing comfort and facilitating everyday activities.
  • Voice control
  • Remote home control from applications for phones, tablets and smart watches
  • Automatic scenarios - grouping devices, schedules and scenes
  • Control over devices with one button or remote control
  • Combining all elements of the house into one ecosystem
Sustainability: FIBARO will ensure that your home has a minimal impact on the surroundings and the environment.
  • Intelligent heating control leading to a reduction in the demand for heating media
  • Build awareness through the energy panel and measure current electricity consumption
  • The use of dimmers, thermostats or intelligent heads leads to significant energy savings
Savings: In the FIBARO system, your savings are very important.
  • The heating system is intelligently controlled through schedules and the presence of the household members
  • The use of dimmers and LED drivers leads to a reduction in bills
  • The ability to use scenarios and automation ensures that no devices will be redundantly used
Fibaro EcoSystem

Documentation

Fibaro Home Center 3 Lite User Manual  

Technical Specifications

Application Smaller houses (recommended up to 100 m2) and apartments
Number of Supported Devices Recommended up to 40 Z-Wave devices
Communication Technologies Z-Wave 700
Network Technologies Wi-Fi 2.4GHz
CPU Single-Core ARM Cortex A7 900 MHz
RAM 512MB
Flash Memory 4 GB eMMC
Possibilities of Automation LUA, block scenes, panels, schedules
Maximum number of scenes Recommended up to 20 scenes
IP Cameras Support 1 IP camera
Plugins and Quick Apps Support 5 plugins and 10 quick apps
Migration Mechanism No
Operating in Connected Gateways Mode Only SLAVE mode

Product Details

The FIBARO Keyfob is a Z-Wave Plus (500 series) compatible, battery-powered, compact remote controller designed to control devices within your Z-Wave network. With six buttons, which support 30 different actions, the FIBARO Keyfob allows you to control Z-Wave devices within your Z-Wave network and run various scenes defined in your Z-Wave gateway. Configure actions for one, two, three clicks, holding the button and specific button sequences to suit all your home automation needs. The FIBARO Keyfob also features a built-in, configurable pin lock system that automatically locks the device after a short period of inactivity (60 seconds by default) which prevents unauthorized control of your home. Note: This device is currently only compatible with the FIBARO Home Center 2 and FIBARO Home Center Lite Z-Wave gateways. Please ensure that you are running the latest Fibaro firmware (at least 4.120)

Documentation

FIBARO Keyfob User Manual

Technical Specifications

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z‐Wave device type
Z-Wave controller
Power
CR2450 3.0V battery (included)
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor and outdoor use
Operation temperature
10 ~ 40 °C
Storage temperature
-10 ~ 60 °C
Weight
100g
Dimensions
70mm x 38mm x 15mm
Housing
ABS
 
Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information