Z-Wave Smoke Sensor Adapter

 

$74.99

Availability: In Stock

SmokeSensorAdapter

Protect yourself with this battery operated Z-Wave Smoke Sensor Adapter. When the Smoke Sensor installed in house detects smoke, it instantly starts the alarm which will trigger this device connected to Z-Wave network and send alarm message to your smart phone.

You’ll get instant notification wherever you are. Having Z-Wave system installed in your house you have everything under 24×7 control.

 

This Device detects the Siren emitted sound from current Model Smoke and CO Sensors . Allowing you to receive notifications from your house to your smart phone without needing to worry about wiring up additional wires to your existing smoke detectors.

2021 10 08

This sensor is a Z-Wave enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave Plus enabled Home Controllers and its security framework.

  • Completely wireless
  • Z-Wave Smart Start
  • Security S2 protocol
  • Z-Wave 700 chip
  • Long battery life
  • Ease of use and installation

700Chip

10 in stock

Description

Product Description

Z-Wave Smoke Sensor Adapter responds to the high frequency siren sound by your Standard Smoke or CO Detectors. Upon detection of the siren, the device will trigger an alarm response, allowing you to send notifications to other devices on your Z-Wave Network or to your Smart Phone.

The Z-Wave Smoke Sensor Adapter is easy to install and set up with all the mounting screws included in the box of the device.

When the sensor is triggered it will send binary ON/OFF commands wirelessly using a Z-Wave enabled (AUS/NZ version 921.42 MHz) transmitter to assigned controllers, switches, window winders etc. The sensor can be used to automatically turn on fans, turn wireless switches ON/OFF and for security applications within the Z-Wave network.

Integrates with Australian Z-Wave certified (921.42MHz) controllers including:

  • Fibaro Home Center 3/Lite, Fibaro Yubii Home
  • Vera Edge/Plus
  • Smartthings
  • ComfortClick (with Z-Wave extender), Colibri
  • Z-WaveMe
  • Other Z-Wave Plus compatible controllers

smoke CO detector

Technical Specifications

Description
RF Protocol
700 chip, Z-Wave Plus V2 certification
Z‐wave device type
Z-wave binary sensor
Power
1 CR123A battery (Included with Device)
RF Frequency
921.42Mhz – AU/NZ  approved RF for Z-wave
Operation Range
Up to 30m indoor when no obstacles
Application
Indoor use only
Operation temperature
0 ~ 55 °C
Storage temperature
-10 ~ 80 °C
Weight
90g
Housing
ABS

Quick Comparison

SettingsZ-Wave Smoke Sensor Adapter removeYale Assure Z-Wave Digital Deadbolt (with key) removeSwann 2MP(1080P) Thermal Sensing Floodlight Security Camera - 4 Pack removeAEOTEC Flood Sensor 6 removeSwann 2MP SWDVK-845808V 1TB 8CH 8x 2MP Security Camera Kit (8x8) removeAEOTEC MultiSensor Recessor remove
Image
SKUDHS-SNS-SMAD-VISDHS-LOK-DB-YALE-KSWPRO-1080MSFB-4PKDHS-SNS-FL-AEOSWDVK-845808V-AUDHS-SNS-MS-AEO-REC
Rating
Price$74.99$440.00$289.99$79.99$588.00$24.99
Stock

10 in stock

Out of stock

49 in stock

Out of stock

4 in stock

12 in stock

Availability10 in stockOut of stock49 in stockOut of stock4 in stock12 in stock
Add to cart

Add to basket

Read more

Add to basket

Read more

Add to basket

Add to basket

DescriptionSmokeSensorAdapter Protect yourself with this battery operated Z-Wave Smoke Sensor Adapter. When the Smoke Sensor installed in house detects smoke, it instantly starts the alarm which will trigger this device connected to Z-Wave network and send alarm message to your smart phone. You'll get instant notification wherever you are. Having Z-Wave system installed in your house you have everything under 24x7 control.   This Device detects the Siren emitted sound from current Model Smoke and CO Sensors . Allowing you to receive notifications from your house to your smart phone without needing to worry about wiring up additional wires to your existing smoke detectors. 2021 10 08 This sensor is a Z-Wave enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave Plus enabled Home Controllers and its security framework.
  • Completely wireless
  • Z-Wave Smart Start
  • Security S2 protocol
  • Z-Wave 700 chip
  • Long battery life
  • Ease of use and installation
700Chip
Yale Assure Smart Lock Forget carrying around keys; lock and unlock your home with your smartphone. Share digital keys with friends and family, view access history and manage user settings, all from your Yale Assure app. Controlled via the Yale Assure App, Yale’s “Twist and Go” function allows users the unique ability to unlock their door by twisting their smart phone when within Bluetooth range. The “Twist and Go” feature protects you and your family from unintended unlocking. Also offering a backlit touch screen keypad, users have the option of entering a PIN code to unlock the door. An automatic Re-lock function is available so that when the latch is retracted, the lock will automatically lock after a specified period of time. For those times when you don't have your smartphone on you, unlock by entering your unique 4-8 digit pin code on the touchscreen keypad. The Yale Assure digital deadbolt with Bluetooth included Yale Assure Z-Wave Network Module to seamlessly integrate into most home automation and alarm systems. Yale Touchscreen Deadbolt Insitu Hand WEB The YALE Assure Digital Deadbolt (with key) comes with all the features of the keyless version but includes a key set for manual lock operation.
  • Open via keypad or using "Twist and Go" with your smartphone
  • Share up to 5 digital keys using the Yale App
  • Holds up to 12 unique PIN codes
  • Locks automatically after a short period
  • Includes low battery warning and tamper alarm
  • Uses the new Z-Wave 500 series chip
  • Swann Thermal Bullet Security Camera
  • 2MP Resolution Full HD1080P
  • Flood Light Built in
  • Include Cable and Power Supply
  • Suits Swann 4580/4980/5580 Series Recorders
Water Sensor 6. Flood sensor. Leak sensor. Safety sensor. Water Sensor 6. Your home’s 6th sense. We protect our homes in so many ways. With smoke sensors, door locks, and security systems. But more homes are damaged each year by small leaks than by devastating fires or burglaries. Water Sensor 6 changes that, using Z-Wave Plus to silently monitor areas of your home at risk of water and then taking action when the worst occurs. aeotec z wave water sensor 6 Total Control. Water Sensor 6 monitors your home. Wave flood and water sensor Leaks & bursts. Water Sensor 6 can detect minuscule amounts of water – as little as 0.5mm / 0.02” of water. That makes it your first line of defence against damaged plumbing. Floods. Whether a small amount or large, Water Sensor 6 also is perfect at protecting against the floods you can anticipate, such as sumps and in basements. Overflows. Accidents happen but that doesn’t make the damage caused by forgotten taps any less expensive. Water Sensor 6 can alert you to the water you’ve forgotten to turn off before it’s too late.
  • 8 Ch Recorder with 8 Heat Sensing Cameras
  • Day Night Cameras with good night vision
  • Standard Coax Cable included
  • Reliable Wired Connection
  • Fantastic Image Quality at 2MP
  • Works with Google Assistant
  • Protection 24/7 with Free Swann App
  • Thermal Sensing Cameras reduces false alerts
  • Massive 1TB Storage, recorder
  • Dropbox Compatible
  • Designed for Simple DIY Installation
  • 12 Months Warranty
Smart sensors. Invisible sensors. Smart sensors. A smart home should be intelligent and it should be invisible. Recessor is the realisation of that principle. It connects to the AEOTEC MultiSensor 6 and AEOTEC TriSensor allowing either to be seamlessly installed and recessed within a wall or ceiling space. Recessor makes Z-Wave multi-sensors subtle. ZW100a DSE010aDSE010c
Content

Product Description

Z-Wave Smoke Sensor Adapter responds to the high frequency siren sound by your Standard Smoke or CO Detectors. Upon detection of the siren, the device will trigger an alarm response, allowing you to send notifications to other devices on your Z-Wave Network or to your Smart Phone. The Z-Wave Smoke Sensor Adapter is easy to install and set up with all the mounting screws included in the box of the device. When the sensor is triggered it will send binary ON/OFF commands wirelessly using a Z-Wave enabled (AUS/NZ version 921.42 MHz) transmitter to assigned controllers, switches, window winders etc. The sensor can be used to automatically turn on fans, turn wireless switches ON/OFF and for security applications within the Z-Wave network. Integrates with Australian Z-Wave certified (921.42MHz) controllers including:
  • Fibaro Home Center 3/Lite, Fibaro Yubii Home
  • Vera Edge/Plus
  • Smartthings
  • ComfortClick (with Z-Wave extender), Colibri
  • Z-WaveMe
  • Other Z-Wave Plus compatible controllers
smoke CO detector

Technical Specifications

Description
RF Protocol
700 chip, Z-Wave Plus V2 certification
Z‐wave device type
Z-wave binary sensor
Power
1 CR123A battery (Included with Device)
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Operation Range
Up to 30m indoor when no obstacles
Application
Indoor use only
Operation temperature
0 ~ 55 °C
Storage temperature
-10 ~ 80 °C
Weight
90g
Housing
ABS
The YALE Assure Digital Deadbolt (with key) combines a highly secure lockset with an elegant electronic interactive touchscreen. It allows users to effortlessly access their premises using their smartphone and to remotely open the door for visitors when they are away. Forget carrying around keys; lock and unlock your home with your smartphone. Share digital keys with friends and family, view access history and manage user settings, all from your Smart Phone. Yale Keyless Lock Features with key The Yale Assure Digital Deadbolt (with key) is designed for seamless integration with any Z-Wave product or automated control systems allowing you to monitor the status of this device and usage through a centralised controller. Please note when Z-Wave module is enabled Bluetooth is disabled and vice versa. This lock will fit in the place of your existing deadbolt and is compatible with all standard interior and exterior doors. Tapered features of the deadbolt allow it to be used even in applications where the door is not perfectly aligned. If this unit is to be controlled and managed by a single network controller, it is recommended that this Z-Wave lock is programmed through the centralized User Interface (UI) using a PC or hand-held device. This will ensure the best and most reliable communication to and from the deadbolt lock and centralized controller.

Product Support

IMPORTANT: This lock may not be used on moving doors(i.e., cars, trains or similar applications). The lock is designed for residential and commercial applications only and door sizes of 32-50mm. We highly recommend that a secondary entrance is available in the unlikely event of total failure. This lock must not be used on fire doors. Below is all the information you need to connect your YALE Assure Digital Deadbolt to a Vera system. How to connect the systems: • On the Vera Dashboard select 'Add Device' (keep lock in close proximity during inclusion and extend inclusion time for 60 sec) • Select 'Door Locks' > 'Yale Touchscreen Deadbolt Assure Lock (YRD226/YRD246)' • If the lock is new set a new master code as detailed below, otherwise click 'Next' on Vera. How to set up the Master Code:   • Wake up the lock by placing your hand on the touch screen. • Press the gear key in the lower right corner of the keypad. • Press 1 followed by the gear key. • Enter your new 4-8 digit master code followed by the gear key. • Click 'Next' on Vera user interface. To Include the lock in the Z-Wave network follow the instructions below • Wake up the lock by placing your hand on the touch screen. • Enter your master code followed by the gear key. • Press 7 followed by the gear key. • Press 1 followed by the gear key. • The lock will play a 3 tone sound to indicate that the inclusion procedure has completed. • Click 'Exit'. Your lock is now added to your Vera system and should appear on the devices page. ⇒Yale Assure Lock App for Android devicesYale Assure Lock App for Apple devices Manuals:Yale Assure App Quick Start Manual (603KB)Yale Assure Installation Template (292KB)Yale Assure Installation Manual (6.96MB) Videos:Introducing the Yale Assure Digital Deadbolt

Technical Specifications

Description
RF Protocol
Z-Wave Plus, Security version S2

 Extra Camera, More Security Add this camera to your Swann DVR-4580V, DVR-4480V, DVR-4980 and DVR-5580 to cover blind spots  See Everything in Full HD Capture essential evidence, such as faces, license plates, packages & more with crystal clear 1080p Full HD resolution
 Sensor Lights for 24/7 Protection Sensor Warning Light lets you see color at night up to 10m, activated by heat or via the app, while infrared night vision lets you see in black & white up to 30m heat sensing.jpg Heat Sensing Swann’s True Detect™ heat & motion-sensing technology turns on the sensor light & reliably captures & records activity, with reliable push notifications & fewer false triggers
 Security Made Smarter Cut the cost of crime & see what’s happening with this sleek bullet-style camera

SWPRO-1080MSFB-4PK-4-description.jpg

1-keep-intruder-away.jpg1-prevent-crime.jpg1-see-more-than-before.jpg1-peace-of-mind-from-anywhere.jpg

Color Night Vision

Get color video at night up with the Sensor Warning Lights up to 10m. See clothing colours, car colours and more for enhanced evidence.

Monitor the Outdoors

Mount cameras outdoors. Weatherproof design, IP66 rating. Built to withstand rain, shine, snow & dust.

True Detect Heat & Motion Detection

Warm objects, like people and cars, trigger recording, push notifications & the sensor warning lights. It can also be set to record 24/7.

Wide Viewing Angle

Swann’s cameras have a super wide 90-degree field of view to cover broad areas, so that you can have fewer cameras in your property, bringing down the cost of home security.

Compatible DVRs

Add this 1080p camera to your Swann DVR-4580V, DVR-4480V, DVR-4980 & DVR-5580 to cover blind spots around your property.

DIY Installation

Everything that you need is in the pack, including an 18m cable, screws & wall plugs, power adapter & splitter and security stickers. See the section below: What's in the Box.

SWPRO-1080MSFB_1.jpg

What's in the box?

All items listed are new in the original manufacturers packaging
PRO-1080MSFB Sensor Warning Light Security Camera x 4
BNC Cables 18m + Power Supply x 4
Mounting Screws & Plugs
Quick Start Guide
Theft Deterrent Stickers

Product Description

The leak sensor with sensors. Water Sensor 6 is a part of the AEOTEC Z-Wave intelligence range. It’s been designed to protect your home and it’s also been designed to make your smart home smarter. Three separate sensors are crafted into each Water Sensor 6. Each of these sensors can be used to create intelligent home control scenarios via your Z-Wave gateway including the management of underfloor heating, HVAC control, and driveway heating. Water sensor. 4 gold tipped water probes actively monitor for leaks and drips. Vibration sensor. Tamper and emergency events are confirmed by an algorithm that includes vibration detection. Temperature sensor. Crafted for heating management, an inbuilt temperature sensor can monitor temperatures between -20ºC and 100ºC.

Product Support

Manuals: ⇒ Aeotec Water Sensor 6 product manual Works with VeraAeotec LED Bulb with Vera copy

Technical Specification

RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ  approved RF for Z-wave
Z-Wave device type
Z-Wave multilevel sensor
Power
1 CR123A battery is required. (included)
Operation Range
Up to 40m without obstacles
Application
Indoor use only
Operation temperature
0 ~ 55 °C
Storage temperature
‐10 ~ 80 °C
Colour
White
Weight
70g
Housing
ABS
Dimensions
107mm x 61mm x 33mm
Compliance
Z-Wave Plus certified
Warranty 12 Months

Peace of Mind From Every Angle

 Reliable Wired Connection

Protect your loved ones & property with this multi-camera, wired surveillance system with everything you need to do-it-yourself or have it professionally installed

 Heat Sensing

Swann’s True Detect™ heat & motion detection records & sends push notifications when it detects heat from warm objects, like people & cars.

 See More in Full HD 1080p

Full HD 1080p resolution lets you zoom in to discern important details which are essential for evidence, such as faces & license plates

 Set & Forget

Enjoy free local recording for up to a whole year+ onto a massive 1TB hard drive & save still images directly to your personal Dropbox account

 Protection 24/7

Know what’s happening at any hour with powerful night vision up to 30m & the ability to mount the cameras inside or outside.

 Security Made Smarter

Cut the cost of crime & know what’s happening with this expandable Full HD 1080p security system to suit homes, offices, small businesses & retail stores

7580-homesafeview-1.jpg

Speak & You Can See

Use voice commands via the Google Assistant and Chromecast to stream video from your security cameras to your TV. Your security just got smarter. See video. Learn more on the Voice Control page >

True Detect Heat & Motion Detection

Warm objects, like people and cars, trigger recording & push notifications.

Monitor the Outdoors

Mount cameras outdoors. Weatherproof design, IP66 rating. Built to withstand rain, shine, snow & dust.

Protection 24/7

See in the dark up to 30m or up to 40m in ambient light with the powerful infrared night vision which automatically kicks in as the night falls.

Dropbox Integration

Set up the system to upload still images to your Dropbox account in the cloud. So even if your security system gets stolen, you’ll have image evidence stored off-site.

Free Storage with the Massive HDD

The massive 1TB HDD can store months of recordings before it starts saving over older footage. Easily transfer videos to a USB stick or download via network with no ongoing fees ever.

Smart Search Finds Movement in Specific Areas

Select a specific area of the image to search for movement within the recordings. For example, highlight the position of a stolen object and Smart Search will find motion around that area.

SWDVR-84580H.jpg

What's in the box?

All items listed are new in the original manufacturer's packaging
DVR 4580 8 Channel DVR with 1TB Hard Drive
PRO-1080MSB 1080p Cameras x 8
BNC Cables 18m x 8
Ethernet Cable
HDMI Cable
Power Adapter & Splitter
Mouse
Mounting Screws & Plugs
Quick Start Guide
Theft Deterrent Stickers

Product Description

Still perfectly powered. Whichever power method you’re using with your multi-sensor, you can keep on using it with the AEOTEC Recessor. The AEOTEC Recessor has been designed to allow for each sensor’s batteries to still easily be changed, or for the AEOTEC MultiSensor 6’s optional power cable to be used if you prefer to power your sensor without batteries. aeotec multisensor 6 recessor a Still precise. The AEOTEC Recessor doesn’t just convert the AEOTEC MultiSensor 6 into a Z-Wave ceiling or beam sensor, it converts it into a precise sensor. Once recessed, your AEOTEC MultiSensor 6 can be angled up to 30º within the Recessor, fine tuning its measurements and readings to be just where you need them. aeotec multisensor 6 recessor

Product Support

The  perfect accessories. The AEOTEC MultiSensor 6 ships with 4 different accessories, each designed to make the installation of the sensor perfect for your home. ZW100d Recessor. Install the AEOTEC MultiSensor 6 in a ceiling or wall cavity with a recessor (sold separately) and just 12 mm will extrude. Features magnetic clasps for simple removal of the sensor. Mounting arm. (sold separately) Discrete and for corner installations, the mounting arm allows you to rotate MultiSensor 6 up to 360° and refine its field of view by up to 50°. USB cable. (sold separately) After 2 years you won’t have to change batteries if you power MultiSensor 6 via mains power using the provided 1.5 metre USB cable. Tape. Weighing only 74 grams, the AEOTEC MultiSensor 6 can be easily installed with just the provided double sided tape from 3M. Manuals: ⇒ Aeotec Multisensor 6 product manual

Technical Specification

Application
Indoor use only
Operation temperature
0 ~ 55 °C
Storage temperature
-10 ~ 80 °C
Colour
White
Weight
70g
Housing
ABS
Dimensions
(LxWxH) 86mm x 86mm x 43mm
Warranty 12 Months
Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information