FIBARO Smart Implant allows to enhance the functionality of wired sensors and other devices by adding Z-Wave network communication.
You can connect binary sensors, analog sensors, DS18B20 temperature sensors or DHT22 humidity and temperature sensor to report their readings to the Z-Wave controller.
It can also control devices by opening/closing output contacts independently of the inputs.
Supports Z-Wave network Security Modes: S0 with AES-128 encryption and S2 Authenticated with PRNG-based encryption.
Works as a Z-Wave signal repeater.
Allows for connecting sensors:
6 DS18B20 sensors,
1 DHT sensor,
2 2-wire analog sensor,
2 3-wire analog sensor,
2 binary sensors.
Built-in temperature sensor.
This product works with :
Fibaro Home Controller 3/2/Lite
Please note:
THE DEVICE IS NOT COMPATIBLE WITH VERA HOME CONTROLLERS
Before installation
Connect only in accordance with one of the diagrams,
The device is powered with secure voltage; nevertheless, the user should be extra careful or should commission the installation to a qualified person,
Do not connect devices that are not compliant with the specification,
Do not connect other sensors than DS18B20 or DHT22 to SP and SD terminals,
Do not connect sensors to SP and SD terminals with wires longer than 3 meters,
Do not load the device outputs with a current exceeding 150mA,
Every connected device should be compliant with the relevant safety standards,
Unused lines should be left insulated.
Tips for arranging the antenna:
Locate the antenna as far from metal elements as possible (connecting wires, bracket rings, etc.) in order to prevent interferences,
Metal surfaces in the direct vicinity of the antenna (e.g. flush mounted metal boxes, metal door frames) may impair signal reception!
Do not cut or shorten the antenna ? its length is perfectly matched to the band in which the system operates.
Make sure no part of the antenna sticks out of the wall switch box.
FIBARO Smart Implant allows to enhance the functionality of wired sensors and other devices by adding Z-Wave network communication.
You can connect binary sensors, analog sensors, DS18B20 temperature sensors or DHT22 humidity and temperature sensor to report their readings to the Z-Wave controller.
It can also control devices by opening/closing output contacts independently of the inputs.
Yubii, a real all-in-one ecosystem for your smart home Works with over 3000 products from other brands.
Yubii Home is open to the integration of third-party devices thanks to the Z-Wave and WiFi protocols, and it can support one IP camera and up to 5 plug-ins.
Manage your home as you want through Yubii app you can keep your home under control and manage it anywhere you are.
Imagine endless scenarios An intelligent home is primarily about increasing comfort and making everyday activities easier. Automated scenarios, voice control, remote control from smartphones, tablets, and smart watches, will facilitate your daily routine.
The?QUBINO Single Switch (by GOAP) is a Z-Wave module for switching on/off the electrical device (e.g. light, fan, etc ...). The module can be controlled either through the Z-wave network or through the wall switch manually.
This module is designed to be mounted behind a traditional wall switch. The module measures the power consumption of load and supports the connection of the digital temperature sensor. It is designed to act as a repeater in order to improve the range and stability of the Z-Wave network.
Supported switches
The module supports mono-stable switches (push button) and bi-stable switches. The module is factory set to operate with bi-stable switches.
The FIBARO Button is a compact, battery powered Z-Wave Plus device that allows you to control devices and run scenes in your Z-Wave network.
Completely wireless
Z-Wave Plus certified
Supports 6 different actions/scenes
Available in multiple colours (white, black, red, blue, yellow)
Range Extender 6.
The Range Extender 6 keeps it reliable. We all know how annoying weak wireless signals can be. Weak WiFi and poor phone signals are frustrating. Imagine if your smart home was also plagued by weak wireless signals and the same frustrations? Your smart home would not be very smart. The Range Extender 6 from Aeotec ensures that your connected home stays connected. It intelligently listens to the commands and reports that your Z-Wave network sends, actively capturing weak signals and then amplifying and repeating them.
FIBARO Swipe is a wireless, battery powered gesture-controlled pad that allows you to activate Z-Wave scenes or commands with a simple wave of the hand.
FIBARO Swipe has the appearance of a small tablet but instead of a touchscreen, it uses sophisticated motion identification technology to respond to six distinct hand gestures including four directional swipes (up, down, left, right), and two circular motions (left, right). A single gesture or a combination of gestures may be used ? for example, swipe ?down? to turn off the lights, ?up? to open your blinds. With four short swipes, the living room is transformed into a home theater! Swipe?s only limit is your imagination.
Z-Wave Plus certified contactless gesture control
May be used with wet or dirty hands ? e.g. turn on the lights in the kitchen or bathroom without getting the switches or wall dirty
Endless control possibilities ? e.g. wave goodbye to activate your ?going out? scene, swipe up to raise the volume on your sound system, swipe down to close difficult to reach skylight windows, reach out your hand from bed in the morning to activate your coffee machine
Endless placement possibilities ? e.g. visible on the dresser or a wall with your favourite family photos, or hidden away under the kitchen counter or coffee table
Powered by 4xAA batteries or Micro-USB giving you ultimate flexibility
Available in black or white
Content
Product Description
Supports Z-Wave network Security Modes: S0 with AES-128 encryption and S2 Authenticated with PRNG-based encryption.
Works as a Z-Wave signal repeater.
Allows for connecting sensors:
6 DS18B20 sensors,
1 DHT sensor,
2 2-wire analog sensor,
2 3-wire analog sensor,
2 binary sensors.
Built-in temperature sensor.
This product works with :
Fibaro Home Controller 3/2/Lite
Please note:
THE DEVICE IS NOT COMPATIBLE WITH VERA HOME CONTROLLERSBefore installation
Connect only in accordance with one of the diagrams,
The device is powered with secure voltage; nevertheless, the user should be extra careful or should commission the installation to a qualified person,
Do not connect devices that are not compliant with the specification,
Do not connect other sensors than DS18B20 or DHT22 to SP and SD terminals,
Do not connect sensors to SP and SD terminals with wires longer than 3 meters,
Do not load the device outputs with a current exceeding 150mA,
Every connected device should be compliant with the relevant safety standards,
Unused lines should be left insulated.
Tips for arranging the antenna:
Locate the antenna as far from metal elements as possible (connecting wires, bracket rings, etc.) in order to prevent interferences,
Metal surfaces in the direct vicinity of the antenna (e.g. flush mounted metal boxes, metal door frames) may impair signal reception!
Do not cut or shorten the antenna ? its length is perfectly matched to the band in which the system operates.
Make sure no part of the antenna sticks out of the wall switch box.
Yubii Home, your life gets better The whole house in one device: possibility to control lights, roller shutters, gates, doors and windows, electrical appliances, heating and watering systems, multimedia, as well as to detect water leaks, CO gases and fire with a simple command from one single app.
Sustainability and Savings Yubii Home will make sure your smart home has a minimal impact on the environment, reducing its carbon footprint. Thanks to intelligent heating and lighting control, and electrical loads monitoring, you can lower your energy consumption and reduce your heating bills.
Imagine endless scenarios An intelligent home is primarily about increasing comfort and making everyday activities easier. Automated scenarios, voice control, remote control from smartphones, tablets, and smart watches, will facilitate your daily routine.
Documentation
Technical Specifications
? Compatible with any Z-Wave Controller.
? Dimensions (W x H x D) 41,8 x 36,8 x 15,4mm
? Power monitoring accuracy P=5-50W, +/-3W; P?50W, +/-3%;
? Digital temperature sensor range (sensor must be ordered separately) -50 ~ 125?C
??Support for the connection of digital temperature sensor (optional part)
? 2 binary inputs offer the option to connect additional devices such as sensors, switches/pushbuttons, etc, ?
Note!Do not connect the module to loads exceeding recommended values. Connect the module only in accordance with the manual and diagrams below. Use only qualified electricians!
The FIBARO Button is a compact, battery-powered Z-Wave Plus device which allows you to manually activate and deactivate devices within your Z-Wave network and to activate scenes defined in your Z-Wave gateway.
The FIBARO Button supports up to 6 different actions/scenes which are triggered with one to five clicks or by holding the button down. In panic mode, each press of the button results in triggering of the emergency scene.
Designed to be small and light, the FIBARO Button can be conveniently mounted on any surface and in any location (eg. beside the bed or under the desk)
Note: This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.FIBARO Button is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.
Technical Specifications
RF Protocol
Z-Wave Plus (500 series chip)
RF Frequency
921.42Mhz - AU/NZ ?approved RF for Z-wave
Power
ER14250 ? AA 3.6V
Operation Range
Up to 40m indoors (with no obstacles)
Application
Indoor use only
Operation temperature
0 ~ 40 ?C
Storage temperature
?10 ~ 50 ?C
Weight
80g
Dimensions
34mm x 46mm (height x diameter)
Housing
ABS
Product Description
Repeats wireless signals.
Repeats wireless signals.For your smart home to be perfect, its wireless signals need to be reliable. Range Extender 6 captures weak or slow signals and efficiently repeats them on to the rest of your Z-Wave network.
Amplifies wireless signals.
Amplifies wireless signals.Not only does Range Extender 6 accurately repeat Z-Wave signals, it amplifies them too and helps improve the reliability and accuracy of your Z-Wave network.
Big on impact.?Small in size.
Range Extender 6 is a power-outlet friendly device, designed to be as small and as compact as possible without compromising on performance. so that it doesn?t block neighbouring power outlets.
The FIBARO Swipe is equipped with the most precise 3D motion detecting sensor of its kind, which ensures flawless recognition of the performed gestures. It presents a new and innovative way of controlling home automation devices in an intuitive and user friendly way.
The magic of Swipe means you can position it in less conventional places as it will work through solid surfaces, like under a desk or behind a wall. And when displayed, Swipe can be used as a beautifully designed picture frame allowing you to easily change photos whenever you want through a simple to remove front panel. A special gesture controlled menu also allows you to add/remove or reset the device without dismantling it.
With the endless possibilities of a gesture, Swipe is a perfect solution for the elderly and disabled, or people who find technology difficult to learn. Show them how to turn on the heating or ventilate the room without even getting up from the chair.
Swipe needn?t be limited to the home either. Use it in the workplace to help you make the office as comfortable as the home. Control blinds, lights or a projector ? all with a wave of your hand.
FIBARO Swipe features the latest Z-Wave 500 series chip for improved wireless range, security and data transfer rates. Please note: Currently integrates with Australian Z-Wave certified (921.42MHz) Fibaro Home Center 2/Lite controllers only.
Installation
Place the Swipe onto its holder.
Place the Swipe within the direct range of your Z-Wave controller.
Plug the power source into the micro-USB port if required.
Set the main controller in (security/non-security) add mode (see the controller?s manual).
Move and hold your hand close to the center of the pad.
If the device is battery powered, high pitched beep will signal exiting the Standby Mode.
Loud sound sequence will confirm entering the menu, keep holding your hand.
After hearing two short beeps (green indicator colour), withdraw the hand and perform swiping up gesture to confirm selection (two beeps will confirm validity).
Wait for the adding process to end.
Successful adding will be confirmed by the Z-Wave controller?s message and 3 short beeps (green visual indicator colour).