The FIBARO Z-Wave RGBW Controller 2 is a one of a kind, advanced wireless 4-colour LED strip controller. Apart from the traditional RGB channels it also supports the white light channel which allows you to add pastel colours to your lighting decorations.
The FIBARO Z-Wave RGBW Controller 2 also has four analogue inputs supporting any type of Fibaro sensor (e.g. light sensors, wind sensors, pressure sensors and potentiometers operating between 0-10V). This smart feature allows you to use your lighting as a warning for certain events. You could, for example, set your RGB garden lights to turn red and flicker when one of your security sensors is triggered, alerting your neighbours to the intruder and allowing them to notify the proper authorities.
This device has four output channels which means that you can connect and independently control up to four light sources. The FIBARO Z-Wave RGBW Controller 2 also allows you to monitor the energy consumed by the LED strips. Each of the four channels can be monitored independently providing you with all the information you need to minimise your energy bills.
The FIBARO Z-Wave RGBW Controller 2 can control:
12 / 24V DC powered RGB strips
12 / 24V DC powered RGBW strips
12 / 24V DC powered LED strips, bulbs, etc
12 / 24V DC powered halogen lights
12 / 24V DC powered low output power fans
Note: Power supply is not included.
This product integrates with all Australian certified (921.42 MHz) Z-Wave controllers including:
Fibaro Home Center 3/Lite
Fibaro Yubii Home
Configuring Z-Wave Devices:
Z-Wave devices often have several configurable parameters which you can change using your Vera?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active for or the type of manual switch connected to a Z-Wave light controller.
Every available configurable parameter is listed in your device?s user manual. In most cases your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section.
Please check the maximum load before installing or operating. This device must be installed by a certified electrician. For all warranty claims, an electrical compliance certificate from your electrician must be provided.
Technical Specifications
RF Protocol
Z?Wave
RF Frequency
921.42Mhz ? AU/NZ ?approved RF for Z?wave
Z?Wave device type
Z-Wave dimmer
Power
12V and 24V
Operation Range
Up to 50m outdoors, up to 30m indoors (depending on terrain and building structure)
Application
Controlled automatically by pre-set Fibaro devices or manually using any Z-Wave controller
The FIBARO Z-Wave RGBW Controller 2 is a wireless controller which enables you to manage your LED strips and halogen lights.
Wirelessly control LEDs with an unlimited range of colour options
Monitors energy usage
Four analogue sensor inputs
Four dimmer channels
Acts as a repeater expanding your Z-Wave network
On any wall.
The?AEOTEC WallMote?is the wall switch that you can install anywhere. Wirelessly.
Whatever the room, whatever the wall, the?AEOTEC WallMote?is perfect. It is the wireless, Z-Wave wall switch that you can place anywhere, on any wall, with as little as double sided tape. Unpack it. Stick it. Charge it. Control is just a tap away.
Simple to install.
The?AEOTEC WallMote?is the wall switch for anywhere. You can mount it in just two steps!
Attach the mounting plate.
Attach the mounting plate. The?AEOTEC WallMote?s mounting plate affixes to any wall or surface using custom mounting tape. Peel. Stick. Done.
Attach WallMote.
The?AEOTEC WallMote?is attractive. Literally. Simply place it in front of the mounting plate and it will magnetically attach.
Shelly 1PM Wifi Module is the smallest, smartest & most powerful WiFi switch for your automation solution
The Relay Switch Shelly 1PM WiFi Module may control 1 electrical circuit up to 3.5 kW. It is intended to be mounted behind power sockets and light switches or other places with limited space. Shelly may work as a standalone device or as an accessory to another home automation controller.
The User can register and access Shelly Cloud, using either Android or iOS mobile applications, or any internet browser and the website: https://my.Shelly.cloud/.
Mobile App Control?- Turn devices on/off directly from your smartphone or tablet.
WiFi Connected?- Just connect Shelly to your WiFi network and begin the ultimate experience of controlling your home with your phone.
Home assistant compatible - Control your appliance with your voice. The Shelly 1 OS is Google Home and Amazon Echo Compatible.
Weekly Scheduling?- Create custom daily schedules for your devices.
Following the Sunlight?- 1PM Wifi Module can automatically turn on/off based on the sunrise and sunset hours.
Up To 3500W - With Shelly Plug you can control a wide range of devices and appliances.
Shelly for developers
REST API?- With the embedded web server and the common HTTP commands Shelly can be made compatible with Vera, Fibaro, SmartThings, HomeSeer, Savant, HomeKit, etc. Visit our?REST API for developers, to create your own cloud solution.
Support?- Shelly has HTTP/UDP support.?Visit the Shelly forum?for more details.
Shelly Cloud for Shelly 1PM Wifi Module - One App - Unlimited Functionality
Specifications:
Power supply: 110-240V ?10% 50/60Hz AC / 24-60V DC
Max load: 16A/240V
Complies with AU standards
Working temperature: ? 40?C up to 40?C
Radio signal power: 1mW
Radio protocol: WiFi 802.11 b/g/n
Frequency: 2400 ? 2500 MHz
Operational range (depending on local construction): up to 50 m outdoors, up to 30 m indoors
Dimensions (HxWxL): 41 x 36 x 17 mm
Electrical consumption: < 1 W
Note:
The device only works on 2.4 GHz WiFi b/g/n.
Shelly 1PM has a power measurement function.
Shelly 1PM only works with a neutral line.
Shelly 1PM has not dry / voltage-free / potential-free contacts.
This product is approved for use in Australia but must be installed by a licensed electrician.?
The?QUBINO Dimmer?(by GOAP) is the first MOSFET- switching light Z-Wave dimmer module that also supports control of low-voltage halogen lamps with electronic transformers, dimmable compact fluorescent lights and dimmable LED bulbs. It also measures the power consumption of electrical devices and supports the connection of a digital temperature sensor.
QUBINO?modules are ?install-and-forget? products. Our products are made to last, so we only select and use top-quality electronic components. These modules are also the most tested Z-Wave microcontrollers on the market. The Slovenian Institute of Quality and Metrology (SIQ), an independent testing body, tests safety parameters including temperature rise, construction, insulation resistance, power consumption and overload in accordance with the EN 60669-2-1 standard.
Shelly 1L Single wire WiFi-operated relay
Convert any existing wall switch into a smart switch without changing the wiring or running new cables with Shelly 1L. The first device in the world that is able to automate even the appliances wired with no neutral present. Thanks to its small size and wide range of voltage support, it's a real innovation!
NO NEUTRAL REQUIRED. Power and control your light, fan, or other appliances with only a live wire, no neutral required to be connected to the device.
OVERHEATING PROTECTION.?If the Shelly 1L reached high temperatures, it will switch OFF the output to protect itself and your home appliances.
MQTT ENABLED.?Easily integrate Shelly 1L to your existing home server using the MQTT or CoAP protocols
REST API.?Use the REST API to connect Shelly 1L to your existing home automation system.
HIGHLY COMPATIBLE. Compatible with Android, iOS, Amazon Alexa and Google Assistant. Control your appliance with your voice.
SUNRISE/SUNSET SCHEDULES. Shelly 1L can automatically follow the sunrise and sunset and control your lighting accordingly.
This product is approved for use in Australia but must be installed by a licensed electrician.
Shelly Dimmer 2 WiFi-operated dimmer
Control a wide range of halogen lights, dimmable LED and ferromagnetic transformers from anywhere with the smallest WiFi-operated dimmer in the world ? Shelly Dimmer2 working without a neutral line.
Shelly Dimmer2
has an embedded webserver
has been designed for installation in a limited space, such as wall mounts, electrical control panels, etc.
can function as a standalone device, as an accessory to a home automation controller, or it may be used as another automation system's component
overload, and temperature protection
This product is approved for use in Australia but must be installed by a licensed electrician.
Content
The FIBARO Z-Wave RGBW Controller 2 is a one of a kind, advanced wireless 4-colour LED strip controller. Apart from the traditional RGB channels it also supports the white light channel which allows you to add pastel colours to your lighting decorations.
The FIBARO Z-Wave RGBW Controller 2 also has four analogue inputs supporting any type of Fibaro sensor (e.g. light sensors, wind sensors, pressure sensors and potentiometers operating between 0-10V). This smart feature allows you to use your lighting as a warning for certain events. You could, for example, set your RGB garden lights to turn red and flicker when one of your security sensors is triggered, alerting your neighbours to the intruder and allowing them to notify the proper authorities.
This device has four output channels which means that you can connect and independently control up to four light sources. The FIBARO Z-Wave RGBW Controller 2 also allows you to monitor the energy consumed by the LED strips. Each of the four channels can be monitored independently providing you with all the information you need to minimise your energy bills.
The FIBARO Z-Wave RGBW Controller 2 can control:
12 / 24V DC powered RGB strips
12 / 24V DC powered RGBW strips
12 / 24V DC powered LED strips, bulbs, etc
12 / 24V DC powered halogen lights
12 / 24V DC powered low output power fans
Note: Power supply is not included.
This product integrates with all Australian certified (921.42 MHz) Z-Wave controllers including:
Fibaro Home Center 3/Lite
Fibaro Yubii Home
Configuring Z-Wave Devices:
Z-Wave devices often have several configurable parameters which you can change using your Vera?s user interface. These parameters can include things such as the length of time a Z-Wave siren remains active for or the type of manual switch connected to a Z-Wave light controller.
Every available configurable parameter is listed in your device?s user manual. In most cases your device?s default parameters will be suitable to your needs however sometimes it may be necessary to adjust them to optimally use your device. A guide to configuring Z-Wave devices with Vera UI7 is available in the Manuals section.
Please check the maximum load before installing or operating.This device must be installed by a certified electrician.For all warranty claims, an electrical compliance certificate from your electrician must be provided.
Technical Specifications
RF Protocol
Z?Wave
RF Frequency
921.42Mhz ? AU/NZ ?approved RF for Z?wave
Z?Wave device type
Z-Wave dimmer
Power
12V and 24V
Operation Range
Up to 50m outdoors, up to 30m indoors (depending on terrain and building structure)
Application
Controlled automatically by pre-set Fibaro devices or manually using any Z-Wave controller
Control on tap.
Control one Z-Wave device. Control many. And all with a single tap.
There is simplicity in tapping touch glass. smartphones proved it. There is power too. Each of your?AEOTEC WallMote?s buttons can be programmed to control one Z-Wave device or many. Meaning that a single tap on its smooth surface can change a single light, a whole room, or your whole home. Tap good morning. Tap good night. Tap all the moments in between.
Control a light. Control a room. Control a home.
Because the?AEOTEC WallMote?communicates directly with your Z-Wave gateway, it can be used to control anything that your gateway can. Even things that are not Z-Wave. Smart lighting from Philips Hue? Check. Connected music from Sonos? Easy. If it is connected to your gateway, simply add it to a scene that WallMote can control and it is on top.
Wireless switch.
To be used anywhere in your home, WallMote and WallMote Quad need to be more than wireless. They need to be impressively wireless. Both switches offer a fine-tuned antenna capable of communicating over an open range of over 150 metres.
Secure switch.
Technology changes, now your wall switches change with it. WallMote and WallMote Quad are cutting-edge today and will be cutting-edge tomorrow. They are both capable of receiving wireless firmware updates via Z-Wave Plus so that they are always up to date.
Subtle switch.
Not just portable, but perfectly balanced. The minimalist design of both WallMote and WallMote Quad measures just 7.7cm wide and a slender 1.9cm deep
Simple recharging.
Battery powered but without the need to ever change a battery, WallMote and WallMote Quad are both powered by a rechargeable lithium battery designed for smartphones. It recharges just like a smartphone too via the provided micro USB cable.
Haptic feedback.
It is capable of controlling your whole home, so you may not even be present to see things change when you press WallMote?s touch glass. But you will feel the change. WallMote?s haptic engine confirms your every action via a click sensation.
Gen5 built in.
WallMote and WallMote Quad are part of Aeotec?s Gen5 range of Z-Wave devices. Built upon the latest version of Z-Wave- Z-Wave Plus ? cutting-edge performance and security is crafted into Z-Wave?s most advanced battery-powered wall switch.
Shelly 1PM Wifi Module is the smallest, smartest & most powerful WiFi switch for your automation solution
The Relay Switch Shelly 1PM WiFi Module may control 1 electrical circuit up to 3.5 kW. It is intended to be mounted behind power sockets and light switches or other places with limited space. Shelly may work as a standalone device or as an accessory to another home automation controller.
The User can register and access Shelly Cloud, using either Android or iOS mobile applications, or any internet browser and the website: https://my.Shelly.cloud/.
Mobile App Control?- Turn devices on/off directly from your smartphone or tablet.
WiFi Connected?- Just connect Shelly to your WiFi network and begin the ultimate experience of controlling your home with your phone.
Home assistant compatible - Control your appliance with your voice. The Shelly 1 OS is Google Home and Amazon Echo Compatible.
Weekly Scheduling?- Create custom daily schedules for your devices.
Following the Sunlight?- 1PM Wifi Module can automatically turn on/off based on the sunrise and sunset hours.
Up To 3500W - With Shelly Plug you can control a wide range of devices and appliances.
Shelly for developers
REST API?- With the embedded web server and the common HTTP commands Shelly can be made compatible with Vera, Fibaro, SmartThings, HomeSeer, Savant, HomeKit, etc. Visit our?REST API for developers, to create your own cloud solution.
Support?- Shelly has HTTP/UDP support.?Visit the Shelly forum?for more details.
Shelly Cloud for Shelly 1PM Wifi Module - One App - Unlimited Functionality
Specifications:
Power supply: 110-240V ?10% 50/60Hz AC / 24-60V DC
Max load: 16A/240V
Complies with AU standards
Working temperature: ? 40?C up to 40?C
Radio signal power: 1mW
Radio protocol: WiFi 802.11 b/g/n
Frequency: 2400 ? 2500 MHz
Operational range (depending on local construction): up to 50 m outdoors, up to 30 m indoors
Dimensions (HxWxL): 41 x 36 x 17 mm
Electrical consumption: < 1 W
Note:
The device only works on 2.4 GHz WiFi b/g/n.
Shelly 1PM has a power measurement function.
Shelly 1PM only works with a neutral line.
Shelly 1PM has not dry / voltage-free / potential-free contacts.
This product is approved for use in Australia but must be installed by a licensed electrician.?
All QUBINO modules are manufactured in Europe by GOAP.
The QUBINO Z-Wave Dimmer module occupies a smaller volume than comparable modules of any other brand and will fit easily in any flush mounting box.
The QUBINO Z-Wave?Dimmer can measure the power consumption of the connected electrical device and itself has an extremely low power consumption of just 0.7 W.
The QUBINO Z-Wave?Dimmer can operate across a wide temperature range, from a chilly -10?C to a scorching 40?C (14??104?F). It supports the connection of a digital temperature sensor, which is also useful for creating complex scenarios. Every module also acts as a repeater in order to improve the range and stability of the Z-Wave network.
Unlimited controlling capability through a gateway
Setting mono-stable (push button) or bi-stable switch type
Z-Wave Plus compliant
23 additional parameters for expert users
Product Support
Please note:?If you are installing the entire Z-Wave? system for the first time, please refer to?the installation guide of your Z-Wave gateway before installing this device.
The QUBINO Flush Dimmer uses a unique MOSFET 'trailing edge' dimmer to enable it to work with a huge range of bulb types:
Halogen and Incandescent (230V)
Dimmable LEDs (230V)
Dimmable CFL and Fluorescent (230V)
Low Voltage Halogen (24V)
Low Voltage LED (24V)
The QUBINO Dimmer can be used in the 230V mains lighting system where it uses a 'Trailing Edge' style dimmer to control the lights. It can also be used in a 24V low-voltage system where it uses PWM style control of the bulbs.
Please note:
These devices require a 3-wire system (including neutral), please check your installation before purchasing. If you have a 2-wire system (without neutral) we recommend you use a FIBARO Z-Wave Dimmer 2PLEASE NOTE FOR THE INSTALLATIONS IN THE AREAS WHERE ELECTRICITY SUPPLIERS USE OFF-PEAK RIPPLE CONTROL SIGNALS:
Electricity suppliers in particular areas of Australia such as NSW, QLD and some other places are injecting an off-peak ripple control signal using Zellweger equipment?or similar onto their distribution networks in order to remotely control devices such as off-peak hot water systems and street lighting, although other areas within Australia also use this technology. Not all properties are affected by ripple control, so just because you might live in one of these areas, does not mean that you will have these problems.
Ripple injection control systems work by superimposing coded control signals, commonly 750Hz or 1050Hz on the 50 Hz mains supply.
Some electrical appliances such as fans, dimmers, toasters and LED lighting can be sensitive to this ripple control signal. The results could be audible buzzing noises from fans or flickering lights whenever the ripple control signals are present.
Electricity suppliers are advising users to install appropriate?ripple signal filters in such areas.
The ripple signal filter is a tuned passive inline filter that completely eliminates the superimposed ripple injection control signal from the normal mains supply to produce a noise-free filtered mains supply which can then be connected to the electrical appliances or light control systems. The ripple signal filter is specifically tuned to eliminate the ripple control signal frequency of 750Hz or 1050Hz.
However, we can?t guarantee the ripple signal filter always will help you if you experiencing such issues. Please contact your local energy provider to get more information and proposed solutions for your electrical installation.
If you are getting similar problems with your dimmers and fans and it?s not Ripple Control Signal and you are hearing the tones at random times of the day, your electrical supply may be affected by harmonics; a power fluctuation that is not part of the normal electricity supply or ripple control signal output.
Harmonics are caused by an interference created by other equipment on the network, such as inverter type air conditioners and switch-mode power supplies for computers.
The offending appliances may be in your home or other premises on the local power grid. If you are being affected by network harmonics, it may be of benefit to transfer the electricity supply to your premises to a different phase in the street. This is something you will need to discuss with your electrical company.
We are strongly recommending for the areas we have mentioned above to run tests with only a few dimmers before committing for high volumes. If results are not fully OK you may use relays only instead of dimmers.Please note that our warranty for the faulty devices is not covering the above-mentioned conditions with your local electric grids.
Please see affected with Ripple Signalling areas here:
QUEENSLAND
Only Southern Queensland (Energex) has Ripple Signalling.
The Frequency is 1050Hz.
The rest of Queensland (Ergon) does not have Ripple Signalling.
NSW
Energy Australia Full Supply Area
Energy Australia Sydney &Hunter Supply Area
Shelly 1L Single wire WiFi-operated relay
Convert any existing wall switch into a smart switch without changing the wiring or running new cables with Shelly 1L. The first device in the world that is able to automate even the appliances wired with no neutral present. Thanks to its small size and wide range of voltage support, it's a real innovation!
NO NEUTRAL REQUIRED. Power and control your light, fan, or other appliances with only a live wire, no neutral required to be connected to the device.
OVERHEATING PROTECTION.?If the Shelly 1L reached high temperatures, it will switch OFF the output to protect itself and your home appliances.
MQTT ENABLED.?Easily integrate Shelly 1L to your existing home server using the MQTT or CoAP protocols
REST API.?Use the REST API to connect Shelly 1L to your existing home automation system.
HIGHLY COMPATIBLE. Compatible with Android, iOS, Amazon Alexa and Google Assistant. Control your appliance with your voice.
SUNRISE/SUNSET SCHEDULES. Shelly 1L can automatically follow the sunrise and sunset and control your lighting accordingly.
10 PackThis product is approved for use in Australia but must be installed by a licensed electrician.